0:00 The Big Power Upgrade Plan 7:40 Removing the Old System 13:58 Battery Comparison - Old vs New 14:30 Installing the New Battery Shelf 19:46 Fitting the New Fogstar Batteries 23:33 Connecting Batteries in Parallel 27:50 New Electric Component Board 42:28 Installing the New DCDC Chargers 44:05 New System Reveal 44:44 System Summary, Website & Thanks to Partners The full electrical system rebuild on my self-converted van — upgrading the off-grid power system to a 1,256Ah Fogstar Drift lithium battery bank, 2× Victron Orion XS 70-amp DC-DC chargers and a custom 300A high-output alternator. After two years of full-time van life, the original 460Ah single-battery setup couldn’t keep up with a full studio setup, induction cooking and weeks off-grid between hookups. The redesign is built around one idea: charge as hard as possible while driving, store enough to go weeks between fills. The new build delivers 140A of alternator charging on the move, with Victron Lynx Power In distribution, 95mm² battery cabling and MIDI fusing throughout. Full parts list, costs and discount codes linked above.
AI Generated·May contain errors
Video Summary
AI Generated
The creator is upgrading his camper van's electrical system to enhance winter off-grid autonomy. The project involves tripling battery capacity to over 1200Ah, increasing charging power to 140A via dual DC-DC chargers, and installing a 300A heavy-duty alternator. The upgrade emphasizes professional cable management, structural reinforcement, and a shift toward manual controls for critical systems.
It's finally finished. All right, you guys, big day today.
If you couldn't tell from the title of
the video, we're going to be tripling the power
that I have in my self-converted camper van,
which I've been traveling in for the last couple of years.
And although I have a pretty cool power
system, and for those of you who haven't seen it,
this is what my current power system looks like.
So we have all of my Victron gear down the bottom here,
and then we have my Roma.
460 amp hour battery at the top.
And although I have a really decent power system on the van,
I have found that during the winter,
normally I tend to run out of power
within sort of five to seven days
if I don't really drive anywhere.
And if we have weather where it's just really dark
and gray out or it's just raining constantly,
although I have really great solar panels
that charge the battery, even when it's cloudy,
they're the Renogy Shadow Flux solar panels, I think.
And I have 600 amp hours of solar on top of the roof.
So we've got plenty of solar.
solar but I do still struggle if I don't kind of drive anywhere
and I'm just kind of sat around for
three or four days without going anywhere.
I do find that I run out of power in the winter which
sucks so I've always wanted to have more storage of power on board
and also a way to charge the
batteries more when I'm driving.
I'm going to be doing a few big upgrades today. I'll take you
through step by step. There's a lot I've got
to do to be able to get all this done but basically
Basically, we're going to be removing this Romer 416
60 amp hour battery here
and we're going to be replacing it with two fogstar 620 amp hour
batteries. Now these are the batteries down here
so we've got one out of the box already that's a
620 amp hour one there and then the other one is in the box here
so we're going to have two of those
and you might be asking yourself where am I going to fit them well
Wow, that's big.
It's been one of the biggest challenges.
So what I have decided to do,
and I'm sorry for the lighting this morning,
like the sun's just coming up behind me
and I can't get the exposure right on the camera.
So just bear with me.
So at the moment I've got here,
this is the Roma battery and I built this plinth
to put it on.
This top bit here is just kind of a retainer.
And then the actual shelf is kind of starts here,
which is where the battery sits on.
But this is a bespoke shelf made out of C16 timbers.
And they go straight down to the floor of the van down here
It's quite a big beefy shelf which really didn't need
to be that big I suppose but I did it because I just wanted
to make sure that you know it took the weight but what we're going
to do we're going to take out the battery we're going to take out
this whole kind of plinth and shelf and remove that all together
and then the guys at Evo Customs have hooked me up with a new shelf
so thank you guys I appreciate that and they've also hooked me up
with a bunch of other goodies which I'll show you guys throughout
this video and probably in another video as well some more additions
to the van which we're going to be doing
so we're going to swap this shelf out for a new shelf that has
It hasn't got a big cutout in it because obviously I don't want
this cutout anymore and then all we're going to do is strengthen
this shelf underneath so that it can take the weight of the battery
that's going in here and I think each battery is 54 kilos
and then we're going to do the same in this cabinet here
so all I need to do is take out that kind of divider that's there
and then that shelf can be strengthened
and then the battery the second battery can go straight in there
and then I'm going to connect them both in parallel so the cables
are run from this battery they'll run on the inside of this
beam here all the way over go into the top
of this cabinet and connect to that
battery in parallel and then from there they'll go
to my links power in to then
power the whole system now that's just kind
of like phase one there's a couple
of different phases of this which i'm
doing obviously there's that i also have
Two new DC to DC converters from Victron.
They are the new 70 amp chargers, which are coming into this country.
I think they're due in next week.
I don't even know what the date is at the moment,
but they're due into the country around the 24th of August, I think.
I'm one of the first people in the country to have them,
and I'm really, really stoked about it.
So we're going to be going from a 50 amp DC to DC charger,
which I have on the van at the moment, to...
Two 70 amp DC to DC chargers from Victron, which is huge.
It does mean though that I have to reorganize this board.
I have to take everything off.
I've got a new board which I need to cut down to the right size
and then I need to remount everything.
I have another Lynx power in because I need two of these side by side
to be able to take all the cables that I've got to run.
Then we're going to have two 70 amp DC to DC chargers over there,
which is going to give us 140 amps of charging while driving,
Which is just ridiculous because it means
As soon as I turn the key and I start driving,
I'm also going to be having triple the amount of
charge going into the batteries than I used to have.
I'm not going to know myself when this is
done. And then you might be saying to yourself,
well, John, surely if you're upgrading those
charges and you're taking 140 amps of charge from the alternator
or from the vehicle battery
to those batteries, surely you need
to upgrade your alternator. Yes, I do.
I do.
This is what I mean, it's been literally a knock-on effect
of everything, like to do the batteries I knew I had
to do the weight upgrade, but to do the weight upgrade I knew I had
to do the suspension underneath.
We've upgraded the suspension underneath.
So that I can upgrade the vehicle weight,
so that I can take the batteries, but to have the DC-DC
chargers, which are going to be producing 140 amps off
of the vehicle alternator, I've also
needed to uprate the vehicle alternator.
I think the standard one that's on the van at the moment
is 180 amps, but obviously you have a good amount
of amperage going into the vehicle battery while
you're driving. And then during the winter,
obviously you're running your heaters, you're
You're running lights, you're running demist,
all these different things on.
on the van so you need to make sure you've got enough kind
of buffer room to be able to take
140 amp out of the alternator without affecting the vehicle.
I've got a extra heavy duty alternator
being manufactured or being made for me.
It's costing an absolute fortune but it's going to
be giving me 300 amps of charge from that alternator.
Again 120 amps more than what's
on the alternator at the moment
and then that alternator that alternator should be here by
By mid to end of September and then I can get that fitted.
Anyway, that kind of gives you a kind of an overview of everything
and why I'm doing what I'm doing and
where we're kind of at so I'm going to crack on this weekend
and I'm going to get the shelf done
for the new battery to go in both batteries
in the like I say we've got the batteries here this
is one of them the 620 amp we've got another one here we've got
the battery mounts here we've got
tons of cable and yeah all sorts of stuff we've got
the new Lynx powering up here as well yeah
that's the new electrical board that's the new battery shelf
which I've got which again just
kind of slots in but I've got to sort of dismantle
the cabinet a little bit to fit that and a few
bits and pieces to fit as well. So it is quite a big upgrade.
There's so many bits to doing all
of this that I've had to do in a certain order.
When it's all done I'm not going to know myself.
It's going to be amazing. It's just such a process to get there
and also when I built this van I knew
that I could do upgrades if I wanted to.
Then actually doing them and figuring out like how
to run cables and where to run cables and all the rest of it.
Yeah it is a challenge so anyway.
I'm going to crack on. First job is to get all the doors off,
get the battery out, get the shelf out
and then put the new shelf in and strengthen the shelves.
And then once that's done, we can put the new batteries in.
So, yeah, exciting times.
Alright so little update on where we are.
This is the current state of affairs.
So that's the old electrics board which I've taken all the Victron
gear off and all the Victron gear is kind of down here and up here.
This is the old 50 amp DC DC charger which will be going back
in for the minute until I've received the others
but hopefully the others will be here within the next couple of weeks.
They're pretty much the same size unit.
which is good.
And I like to make hard work for myself.
So every single cable was drilled
with the right size hole,
corresponding to like the cable size.
So that's how all the cables came through,
like nice and neatly for all the charges and things.
And yes, it does add a ton more work,
but it makes it look really nice and really neat.
I'm not sure whether I'm gonna do it on the new one,
because again, it does take a hell of a long time,
but I shall see, I shall see.
I just wanna take a minute
to thank today's video sponsor, Reolink.
This is the Reolink Atlas PT Ultra.
Now I've been back home for the last couple of months doing a
ton of van upgrades and working away on my parents driveway
and having this camera installed now
solves one of the biggest frustrations I've seen
with battery security cameras. Quality footage
and missing the moment right before something actually happens.
The camera's got a 10 second
pre-record feature so the camera
is actually recording before it even detects any motion.
That means if something happens you're not just getting
the footage after the event has happened
or kind of during the event,
you're actually getting those vital few seconds leading up to
the event which in certain situations could be absolutely vital.
It also does full 4k color
footage at night, not the usual grainy black
and white you normally get from most cameras.
So if anything happens after dark you can
actually make out real detail. Faces.
Clothing and number plates rather than just a vague shape
on a grainy black and white clip. It's also got full
360 degree coverage
355 degrees of pan and 90 degrees of tilt.
So there's no blind spots whatsoever.
It'll automatically track movement too
Person, vehicle, animal,
it knows the difference and follows accordingly,
so you're not getting a flood
of notifications every time next door's cat wanders through your
garden. And the battery life is honestly mad,
up to 500 days on a single charge,
well over a year without needing to think about it.
I've actually got mine paired with the solar
panel too, which tops up automatically
and extends that even further, so realistically
I never have to take it down and think about charging it.
And to make things nice and simple, everything is controlled through
the Reolink app, so I can check live footage, get alerts,
and go back through my recordings, all from my phone, wherever I am.
For me, this camera has given me a lot of assurance.
Having been home the last couple of months,
there's been plenty of times where I've had the van parked up,
and I've actually not been around.
I've either been in the garage sorting things out for the van,
or inside spending time with family,
even if it's just popping in for lunch for half an hour.
All the while my van is fully open on the driveway exposed to everyone
so it's genuinely reassuring
that I know the van is covered 24/7 giving me real peace of mind
and even when I'm actually
working on the van I've still got tools out
everywhere everything's open and like I say even
if I just pop in for lunch for half an hour it's still half
an hour anything can happen in that
And I can still see the van on my phone
and get notified if there's any movement around it,
even if it's just the local postie
or delivery guy dropping something off.
So if you guys want to check out the Atlas PT Ultra for yourselves,
then check out the link in my description below,
head over to their website,
and you guys can get 5% off using code JOHNROMES5 at checkout.
Or you can scan this QR code, which
will take you straight to the website.
A massive thanks again to Reolink for sponsoring this video,
and now back to the upgrades.
So this is all the cables that come through
from everywhere in the van they are actually all neatly
coming through so this is most of the 12 volt stuff here
and there's a bunch of other stuff
that comes through at the back
and then yeah you just have an array of where it will just
Kind of plugs into the back of the board.
This is spaghetti junction.
Going to clear this up and clean this up
and make this all look really good.
And then this is where I just pulled the battery out.
You can see here the battery used to sit in here
and it sat up against this.
And then there was another one of these,
which I had here, which I've just taken off.
And then there was one in the front as well.
And they were all screwed down, which stopped any kind of lateral
or horizontal movement of the battery.
And then I had a strap going over the battery,
which went down the side here.
And it was a ratchet.
I just strapped this one here,
which basically strapped the battery in place.
That's how it stayed in place back there.
So the next job is gonna be to get this shelf out,
because as you can see, this is where I cut it.
So we're gonna be taking this shelf out here.
I just need to undo the screws up here,
which hold this piece in.
Yeah, that's kind of how it fits together.
So I need to lean this off, pull the shelf out,
and then I can get rid of all this
and then bolt the new shelf in.
And then once the battery support is all removed
and that new shelf is in,
I can then work on tidying all the cables up,
working on a new support for underneath this shelf,
which is basically gonna be some like two by one,
a couple of strips going kind of long ways across it,
and then some going down.
And then once I've done that.
The new battery tray can go in, new batteries can go in,
and yeah, we're kind of on the home
straight after that. So I mean, there's a ton of work to do,
but it's going well. It's going well.
But this is the old battery. Here's a little comparison.
So this is the Roma 460, which I've
taken out, which I've been running for the last couple of years.
And then this is the new Fogstar
Drift Gen 2 628, which we're going to be putting in.
So you can see there's quite a bit of
The difference this one is definitely longer by about kind of this much
Yeah, I'm excited to get it in.
So we've got two of these going in.
There's the other one in the box down there.
But yeah, we've got two of these going in to replace this one.
We're going from 460 to just over 1200 amp hours,
which is going to be amazing.
All right, so this is the one I've just taken out.
This is the, I'll put it over here.
This is the shelf even that I had
and obviously it's cut around the battery support that I had
that was to allow cables to come through
and as you can see it actually slots in it's kind of
jigged out CNC'd out here to slot into the cabinet at the side
so not only does it screw
in from underneath but you've got this kind
of whole support here for the shelf and then this
is the replacement one which is how it came
to begin with so obviously you've
Got your black edge banding along the front of the shelf there.
That's where the latch goes onto.
And then this is the piece that slots in on the side.
This is the battery.
Shelf that I originally made so obviously you can see you've got kind
of like C16 structural timber here here
And then there's one at the back here
and then you've got this nice strong shelf for the battery to sit on
but I don't need this anymore because all i'm going to do is use
the normal shelf and then strengthen it underneath which is
Kind of what I should have done to begin
with but I wanted to get the battery in place
Last time before I actually um had all the cabinet trees,
but i'm just going to lift this up as you can see
it's just literally a wooden framework that I made and uh
Yeah, put carpet over the top.
So yeah, dismount all this, shelf goes in,
battery goes in.
All right, you guys, I think I know what I'm doing
after a little bit of head scratching
and trying to figure a few things out.
This is the original battery shelf here,
which obviously we're not having that cut out,
but I do still need two holes here
for the positive and negative cables
to come through from the battery
down into my electrics board.
So this is the new shelf, which is in place now.
And as you can see, I've got the battery bracket,
which is gonna be bolted down, so.
This is loose at the moment and these
are really nice. You can get these from
Fogstar as well with the batteries.
It's all folded steel, it's all powder coated,
really really nice finish on it.
We're going to kind of bolt that around about
there. We're going to leave a little bit
of room up this end just to get the strap in
and leave a little bit of generous room here
so that we can put our two holes in here for
the power cables to then run down into here
which will then go into our links distributor.
And for those of you who don't know what a Lynx distributor is,
it's basically like a buzz bar.
We'll have our main power cable going off
that and then on the Lynx distributor there'll be like
my DC-DC chargers connected, solar chargers,
all my 12-volt fuse boxes for all of the 12-volt
supplies on the van, all of the things.
But I'll show you that when we get onto the panel.
What I'm going to do regarding supporting this shelf,
I'm actually not going to do too much
because I've cut this band here
which I need to screw in place. So we're going to have an
I have an upright support here.
We're going to have an upright support down the end.
But the actual electrics board, I'm just going to cut it
so it is flush fit bottom to top so that it goes all the way along.
And then basically that will just give me support as a downward force.
So any weight that's in the center
here will just be transferred straight
onto that board.
And because it will be a nice snug fit all of the way,
it will just be kind of sat on that board there.
I don't actually need to do any kind of extra battens along here
or uprights or anything like that.
I think I'm going to keep it simple.
Simple is best.
And that's what I'm going to do for that.
it's probably like drinking through a fire hose all
this information I'm giving you but I thought
it'd be kind of cool to show you guys a little bit
of the you know the kind of process and the
behind the scenes of all of the electrics
and all of the stuff that goes into making a camper like
this run and work and stuff
so I know it's a little bit different from the adventure content
and I don't really enjoy watching tons
and tons of like van build videos. I'm one for like I'll
watch like one or two videos to find out what I need
to do and then I'll kind of skim through the
that I need to and find the information I need
and then yeah I'll crack on. I didn't want my
channel to be absolutely littered with like loads of van build videos
and how to fit a kitchen tap
and how to fit a Max Air fan like I'm just
not interested in creating that stuff but I thought
this would be kind of interesting to you guys
to show you the whole upgrade and everything that
goes into it so yeah I'm gonna crack on I'm gonna get all
of this kind of like put together and then
uh yeah I'll catch up with you guys in a bit
when I've um yeah got a little bit further on.
We'll be right back.
I don't know if it came across
on camera just how hard that was to get that in.
I mean it wasn't that hard, it's just awkward.
Heavy. But it's in. Look at that.
That looks awesome and it fills the cabinet. It's like,
I think it's like 54 kilos the actual weight of the battery
so that's why it's so awkward
and obviously I've got no height to play with.
So what I ended up doing was I actually cut two
bits of timber and I placed these on the mat
because the mat underneath kept sliding back
every time I was trying to push the battery in.
So I basically put these on top of the mat,
slid the battery in on these and then yeah just lifted
the battery slightly and pulled them out
out and then drop the battery down. But all the straps are on. It's
It's on there, nice and firm, which is good.
And yeah, I'm excited.
I think I've earned myself like a 10 minute break, so.
I'm going to go and do myself a drink
and then I can look at getting the holes cut in the top here.
So all I'm going to do is drill a couple of circle holes.
I'll measure out where these are and then
my cables will run along here from the other battery.
They'll run along here and go straight through here,
onto here and then the other cables will come off
and they'll go down those holes there which will
then come onto the links powering which is the glorified
Buzz bar.
We're making progress.
And I always like to try and do it as best I can.
I know there's other people who have
probably got way better tools than I have
and way better equipment and workshops and things,
but I'm just doing this with the knowledge that I have
and the tools I have and the time I have available to me.
So, yeah.
Look at that.
Got the other one to get in now so it's gonna go in there.
I'd like to try and get both batteries
in today and then I can worry about doing all the cabling
and the board and everything tomorrow so
if I can get both batteries in today that'll be uh that'll be amazing.
Final update for today because uh my knees are ruined.
I've been out here all day just like yeah.
Getting done but we've made amazing progress.
Obviously the main batteries in here, I mean
they're both main batteries.
It's in place and then we have this one in place this side as well
and I've also made up the positive cable.
This is going from the positive terminal here out through
here and I've not put the holes,
I've not drilled the holes directly above the terminal because I
wanted to angle the lug slightly so that they go off
and then up out the hole. Otherwise you're
Otherwise you're going to try and like...
point it upwards and you'll just put too much strain on the cable.
Yeah so the holes are drilled
and then that goes across all the way down
and connects to the other positive terminal
on this battery here and then it goes through the fuse on the top
and then goes down to my master switch which is around here and then
yeah it will come through there
into the links distributor and then out to the
Out to do all of the things and then I've just made up this cable here.
So I didn't record this process because
quite frankly I couldn't be bothered.
I was too tired.
But this is a 1.5 meter cable that I cut.
I got like three meters sent over because I needed to renew
a couple of the other cables in here to make them long enough.
So we've got one and a half meter cable here
and then all I've done is obviously put the lugs on the end.
I put a very slight bend on them as well just
to enable me to get a nice run off the battery.
And you can bend these lugs.
If you're very very careful you can put a slight bend.
Bend on them because they're copper copper is quite soft put them
in a vice and just very very slowly bend them a little bit
and then I use a vice just to kind of crimp them back in the shape
and yeah they're good to go and then I make up the make up
the lugs crimp them on the end put the heat shrink
on which has already got the kind of adhesive glue inside
and yeah that's it so I've done both ends of that one
so that's the earth which is going to run from this battery
to that battery and like I say the live cable is already done.
all the way across here
and then from the earth on this side we'll have this little one here
which will go to our smart shunt
and then from the smart shunt it goes down to the
links distributor but i think i'm going
to get this earth cable in and uh call it a
night because i'm pretty tired
so yeah i'll catch up with you guys in the morning
Good morning, let me show you guys
the progress I made yesterday after I turned the camera off anyway.
So we have both batteries connected in parallel.
So this is the first battery here and then
obviously we have the cables coming out
and as I said I've drilled the holes kind of offset so that
we have a nice kind of angle on the cable
and it's not under any strain and the same with this one.
These both come off and they're going to come under the bed.
I've got them all cable tied to the
Bed frame here.
So they come across and then they drop down
to the second battery in here and then we've got
this one here this is the earth
which comes off to our smart shunt and then from our smart shunt
this cable goes off and comes out under here which will go to the
links power in which is basically our bus bar and then the power
Obviously it goes from the first battery all
the way down to the second battery linked in parallel
again so positive to positive and then it goes through our,
I'm not sure if the camera's going
to pick it up in here but we've got a big fuse
on the top of the battery there and then obviously
the power is on the top and then comes down that cable
and out under here and then from there
it goes to oh god
From there it goes to our switch which is down here
so that is the battery isolated switch and
I have it in this cupboard and not anywhere over here
because it's nice and easy to get to all I've
got to do is open this door
when it's actually on and I can just kill the power straight away
and it kills all the power to the system
so it's a little bit of a kind of safety thing to have it
in there. I was going to put it on the outside here
but I thought you know what like it doesn't
take a lot just to open the cupboard and kill the switch
and uh yeah that's kind of where we got to
So batteries are in.
Shells are all strengthened,
cables are run and I'm really really happy. I've now got to tackle
all of this in here because all these cables
are just kind of shoved in the back and it does need
a little bit of organizing
and I've got to kind of pull them through and put them into the new
electrics board which I'm yet to make up.
It's kind of the thing I was looking at this morning.
This is the original electrics board that I made. We had things like
The solar charger used to go,
yes the solar charger went on there and then as you can see
I drilled all of the holes according to the cable sizes
which went through the board and then
obviously the same here.
It took a very long time to kind of lay everything out and find out the
kind of angles of the cables and where they could all go
and I kind of do want to do the same thing
because I think I said yesterday although I'm looking to try and
do this as quick as possible and save a little time here and there.
I was really proud of how
the electrical system looked
and although it took me a hell of a long time I don't really want to
cut corners like that. So this is the new electrics board.
Now we have a couple of extra components. I
don't have any more space which is really frustrating
because I need to try and accommodate
two extra components. We have another Lynx power in here
which is basically, let me show you on the
It's basically a fuse board.
The Lynx power in is like a Lynx distributor. The Lynx distributor
just has basically a circuit board underneath here
which just has funky lights and then you
can see the lights here and when a fuse blows the light goes out
and these are actually like half
the price and you just buy a little conversion kit
and you can save yourself a ton of money so
I use the Lynx power in instead.
We've got all our fuses here so we have the power in,
so the power from the battery is on this one
and the earth from the battery is on this one
And then we have all our circuits connected
along here with our different fuse ratings
so we'll have like the solar charger this will go
to like the inverter this will go to like
a dc dc charger you know my 12 volt supply for all the 12
lighting and all that stuff
so that's basically what those do if you don't know but i obviously
only had this one in the system before
and i need another one because i've got another
dc dc charger we're putting in
So this is the new board, which I've come up with.
We've got our two buzz bars here, our links distributors.
Now they are also joined together.
So you obviously just have these terminals here.
You just take these covers off.
Can't get them off.
Yeah, gotcha.
Right.
So you have these terminals here
which you can obviously bolt through so you can put as many of
these in line as you want
to and you have like there's another smart shunt that Victron do which
you can kind of bolt here and it all looks really nice
when it's all kind of connected together. So
we've got our secondary Lynx power in here
so we've got the two connected together and I figured
this is how it's going to look when it goes in the van.
We're going to have our two Lynxes here
With our cables going out to where they need to go
then we're going to have the solar charger at the top which
is where it was before but I've now moved the DC-DC charger to here.
We're going to have another DC-DC charger here
so the 270s will sit here nicely
and then we're going to have our Cerbo GX here and then our...
12 volt fuse box here.
Now I've been out here for about an hour and a half
this morning with a coffee,
just literally playing around with this,
trying to figure out what's the best kind of way
to have all this placed.
And you might be thinking that this is upside down,
but you do have in the kit with these,
you have a sticker which you can put over the top here,
which basically takes this text
and turns it around the right way.
So you can actually mount these any kind of orientation
that you like for ease of use.
So yeah, we're gonna be mounting them.
kind of upside down if you want to call it
that and then our obviously our cables from our battery
will come in here. I'll probably drill two holes offset them slightly
and then the cables will come
up onto there and like I say I was looking for kind
of an easier way of doing it and I was going
to use like conduit and I was going
to have like conduit just like drill a big kind of groove right
in the center and then have conduit just running
and then feed all the cables into that but I also
didn't really want to do that because this board
is actually going to be a little bit of a structural
drawboard as well because it's going to be it's
a very nice snug fit I've cut it this
morning so as it just literally presses in nicely
so as it supports the battery
above and that shelf above
so yeah I didn't want to I didn't want to go cut
in like a massive cut in the middle
and then have the kind of board weakened you
know anyway that kind of brings you up
to speed as to where I'm at this morning
so I think what I'm gonna do is I'm gonna spend
the next few hours marking
out where all these components
are gonna go exactly drilling all the holes
securing them all in place
and making sure I'm 100% happy and then once all
Once all that's done,
I can get all the wiring sorted out in the van
and then look at getting this mounted in place.
And although I don't have the DC-DC chargers yet
because I think they're due into the country next week,
I'm one of the first people in the country to get them,
which is super exciting.
And yeah, batteries and solar have hooked me up with that.
So thank you guys.
I really appreciate that.
Everyone who I've worked with in this video
for all of these upgrades and stuff,
I'm going to link in the description below.
Some of them are components I've been given.
Some of them are partly gifted,
but everything will be below.
And, you know, I'd be using all of this stuff anyway.
So, but yeah, I'm really, really excited
to get those DC-DC chargers,
but I'm going to run all the cables for them
and pull everything through
so as that everything is good to go.
And then when I get them,
I can literally just crawl in there,
screw them in place, connect them up,
put the fuses in and we're good to go.
With all that said, it's time to crack on.
So I kind of left you guys hanging yesterday.
I got way into this board and figuring out
where everything was going to go
and drilling all the holes and things and yeah I'm really
pleased with how it's come along. So this is where we're at.
Link's distributors down the bottom here
which are obviously the fuse holders for the van
so as you can see I've kind of labeled them there
as well so I know what's what
and this will be the one that gets switched out for an 80 amp
when I upgrade the two chargers which are going to go in there
and then that gives me three extra
Spots on the bus bar.
at the end there which is good if i want to add anything over time
and then obviously i have all
the holes drilled for the buzz bar
and all the main cables here i've got the 12 volt fuse board
which i've literally just finished doing now
so we've got our earth and our power in and then we've
got all the supplies i've just got to drill two final holes
at the bottom here to allow the earth
to come through normally what i did on the other one
is i just drilled one hole and then brought
them all through in kind of a clump so i'll do the same
because you don't really see the bottom but
It's nice to have them all individually done.
done at the sides it looks really nice
when they're all kind of laid out. I routed these
out as well which I didn't do on the last one I
had individual holes caught it just there with
the router which was annoying.
What I'm probably going to do I've got some black wood dye so I'm
going to kind of dye the uh dye the wood here
and in all of the holes black so you don't really
kind of see the ply through it
and then yeah we've got one charger here.
the other charger will go here
and then our solar charger here and then what i've done
is obviously you've got all your holes for your like
the battery cables that come in here and the
solar cables that come in and then i've drilled
a hole here for the the v direct cables so the
data cables so the v direct cables
so you need quite a big hole for these to go through um
so i've drilled a i can't remember what size hole it is now
but i think it's like a 12 no
16 mil. It's a 16 mil hole.
So I've drilled a 16 mil hole so I can get these through.
But what I thought would be really cool
is like once I pass them through this hole,
is I've then got these little grommets,
because you're left with quite a big hole with just a
skinny little cable coming through.
So we take these grommets, I've cut them,
put it around the cable,
and then I can press it into the hole nice and neatly,
and then put our cable in to the component,
so in this case the solar charger, and then
This is how they look when they're actually on the board.
So you've got the V-Direct cable here.
There's kind of a nice bend
and it goes straight into the back of the board.
And then, yeah, you've got the kind of grommet
there, which just kind of hides it.
And it's a nice push fit.
I figured if I do that on all of them, I've got them.
So it's these little grommets here,
a little bit sawdusty at the moment.
But so we've got another one which is going to go there,
another one there.
So that's for the...
um two solar chargers and then i don't need another one
for the smart shunt because that's
already on the van next to the battery
so but i thought they look really good and i've had just
enough space to be able to do it with all
the other cables that are coming through so it's
little things like that that make me really happy
i've uh i've always kind of grown up knowing that
the differences in the details like if you take
the time to do a job like if the job's worth doing
it's worth doing right that's why i kind of wanted to do this right
and not kind of rush it although
Although I'm having a little bit of a time crunch and then in the back.
I managed to sort out all the cables yesterday
so we've got all of our all of our 12 volt circuits
coming through here which is all this lot
which needs to go in the fuse board. We've got our big
cables here ready to go which are going to go
into the Lynx distributor. Sensor wires and stuff for
the water tanks they're all down there
and then this is all the data cables which are going to go
into the servo.
Obviously, I've already showed you the battery's already hooked up,
ready to go, so yeah, it's coming on.
See, I'm really happy with the progress. It's day three of the install,
so I started this on Thursday, and it's currently Saturday.
It's around midday, so I'm going to grab some lunch,
and then I think what I'm going to do is just double-check
and make sure I'm happy with everything on the board.
Then I can use the wood dye, get all the holes kind of dyed,
as it were, and then, I think, once I've done that...
It's a case of I need to make up a couple more cables,
put some lugs on some cables,
and then I can start connecting everything.
And then the only really big job I've got left,
which I do want to do today.
Oh, ******* get out of the van.
So for the two new battery chargers that I'm running,
I do need to run a new or two new lengths of cable,
which is this stuff.
Here, so I've already put it in some trunking.
This is going to stop it from obviously chafing underneath the vehicle.
These two cables need to go into a fuse box, ideally.
Where is it?
So they need to go into this little fuse box,
which is going to be connected to my vehicle battery.
And then those two cables, they'll be fused individually.
And then they will come, they will go underneath the vehicle.
All the way up into the inside of the electrics box
and then they will be connected to the DC-DC
chargers. But obviously I needed some much thicker cable
to be able to run these new 70 amp.
charges I'm getting. If I can get that cable run today as well
and have everything good to go and
good to plug in then ideally I don't think I'm going to be ready.
I was hoping to be able to do
like a switch on tonight and test everything
and see if everything's kind of working but to be fair
it's probably going to take me the rest of today to get that cable run,
get all the cables bought
through. Like it takes an immense amount of time
to bring all the cables through, to crimp all the
lugs on, do all the heat shrink
and get everything like really neat and tidy. Like it's probably
The rest of the day today, the rest of the day today,
and all of, I don't know, probably tomorrow morning as well.
I think if I aim for tomorrow lunchtime to be able
to have everything kind of installed, all connected and ready to go,
then I can kind of do my big switch on tomorrow afternoon.
Then that gives me a little bit of time afterwards
that if something isn't right for whatever reason,
then I can obviously do some troubleshooting.
But fingers crossed, everything's going to be fine.
So, right, time to get some lunch
and then crack on with the next stage.
after i started this electrical upgrade
and six months since i initially kind of had the idea
started thinking about it
and getting plans in place it's finally finished and i'm absolutely
stoked with how it's turned out
and the main kind of goal for me that i was kind of thinking about
six months ago when initially kind of thinking about
this electrical upgrade was i just wanted
more time off grid i know that in the uk we have very gray dark winters
Oh my God.
We don't have a lot of light during the days, you know.
Oh man.
Sometimes in the dead of winter,
you'll get kind of five or six hours of daylight,
especially if you're way up north in Scotland.
Okay.
For me,
Charging the van, charging the leisure batteries
while I'm kind of out in the middle of nowhere
is a little bit of a challenge during those times.
Obviously the solar panels aren't going
to generate as much then and because I only had like one 50 amp DC
to DC charger I was very limited
with the kind of charge that I could actually put in the battery
when I was driving. So I thought
it'd be good I wrote some notes down to actually give you guys
so I don't forget anything because
it's taken me a long time to kind of put this video together,
think about everything I wanted
wanted to say and have everything to
to go with it as well because
while I've been doing this I've been updating my website and if
you guys have visited my website you'll know
that I really go to town on things. I really go into
detail because if you've got your own van
and you're looking to do upgrades or if you're looking
to start your own camper van conversion
from scratch it can be very overwhelming. It can be
very daunting and all of the kind of different systems
and things that you find on vans is scary
when you start out. On the website I've actually built my own solar
and battery calculator. I'll
description below to literally everything in this video.
The solar and battery calculator
helps you to calculate wherever you are in the world
the amount of solar that you need on your
roof of your van and then it pairs it with what type
of batteries that you need to go with that.
So for example if you're in a really hot country
and you get loads of sunshine it's never cloudy
you might actually only need to get one kind of smallish battery
and then just have a really large
solar array because every single day obviously
that battery is just going to get topped up all
all the time and you're kind of never really gonna
run low on power however if you're in a country
that doesn't get a lot of sun and you need to
kind of store more power on board for those kind of dark
and gray rainy days then that's when you're
going to need kind of a bigger battery bank
to store that power away to use when you do have
those days where you can't either drive anywhere
to charge the battery or have your solar panels
charging those batteries and that solar
and battery calculator actually uses the entire lineup
of the Fogstar batteries so it takes into account batteries like mine
and you guys can go on there
you can play around with it you can turn things on and off
and you'll see exactly what i mean and
i've had a lot of great feedback on it so far
so i hope you guys find it helpful and there's also
a conversions calculator on my website as well
which if you're just starting out and you kind
of want to put in the cost of the van
and you want to put in the cost of the cabinets and
what electrics you kind of need
and all these sorts of things you basically can turn on and
off a load of different things
and it will give you kind of a rough price of how much your conversion
is going to cost. So again I'll leave all
the links down in the description go and have a play
around with them they're really fun to use
and like I say I've had a lot of great feedback on
them so yeah I hope you find them useful.
And then with regards to this electrical upgrade I have
actually built a new web page on my website
which shows you literally everything. It's got all of
about all of the tech specs of the kit I've used,
from the batteries, the solar
chargers, all of the cables, all of the sizes of the cables.
Links to where I got everything,
literally everything is on there and I also go into
depth about why I decided
to upgrade certain components like why I chose to upgrade to the
Fogstar batteries over the Roma,
why I chose to upgrade my DCDC chargers, what was the reason
behind the alternator.
So if you do prefer to actually read stuff and you like a really good
a good kind of information page.
That's there and I hope that I helped you as well.
And as well as that, I've actually got a
ton of blog posts on my website
which I've written over the last few weeks which covers
literally everything about this upgrade
from reviewing the batteries, reviewing the DCDC
chargers and all of the things in between.
I think I have something in the region of like
Seven, eight, might even be more than
that blog posts I've written over the last month and they're
also all live on my website too.
Honestly there's an absolute ton of stuff on my website and two
other things that you can find on there
are electrical reports that I track all the kind
of electric and all of the usage
and when I plug in and how much solar I've generated every month.
You'll find that all on the website as well as well as my expenses.
So every single month I
track my expenses and you'll be able
to see how much I spend on campsites, food shopping,
Fuel, all of the things in between, those are on there as well.
I did miss a couple of months
which if I haven't done them by the time this video comes out
I will get them done really really soon.
Life has been kind of hectic obviously
but I will get them done soon and then you guys can check
those out and normally I have those done within
a couple of days of the kind of new month starting
and yeah you'll find those all over on the website.
Now I was going to go through the entire electrical
setup with you guys but I think I'm going to be here
for another like 10 or 15 minutes if I do
that so I'm going to give you a very kind of brief overview
and a reason why I chose to do some of
the things I did. Obviously the batteries
are upgraded there's going to be like I say loads
Loads of information on the website.
So please go check all that out
if you guys are interested in this stuff.
But the batteries I basically upgraded
because I wanted triple the capacity that I used to have.
Chargers I upgraded, you kind of know why I did that.
So as I can charge more while I'm driving,
those are the DCDC chargers.
So we've gone from 50 amps
to two 70 amp chargers giving me 140 amps
while I'm driving and obviously I upgraded the alternator
as well so that I was able to actually produce
that amperage for those chargers without kind of
taking anything away from the vehicle side you know
the actual electrics on the van. The only
other couple of things I was going to say
was the switches on the van I've actually changed a few
around so I used to actually run my heater pads for the freshwater
and wastewater tanks underneath
I used to run those through the Victron system as well as the
dump valve for the waste so they're all electronic.
And I used to actually run them through the Cerbo GX
and they used to be controlled by the touch panel inside.
But over the last few years, like many
systems have changed a little bit on Victron.
And I just found it's a little bit clunky kind of going all through
the menus all the time and trying to like find where my dump valve
is this time to actually hit it to then drop my waste.
And one of the other things I did find is that when I do software
updates on that panel and the system needs to kind of reboot itself,
the actual valve itself will then lose voltage
or get voltage again because it's obviously relay operated.
on that Cerbo GX and yeah, wherever I am,
if I'm doing it, if it's rebooting itself,
it will just turn the valve on and drop
my waste everywhere, which is...
Highly inconvenient.
So I thought, you know what,
I'm gonna have a separate switch for that
that I actually control manually.
And it was the same with the heater pads.
So I had two heater pads,
one connected to my fresh water system under the van,
my fresh water tank,
and the other one connected to the waste tank.
And then they ran into the Serbo GX,
and then they were relay controlled
via a temperature sensor.
So when the temperature got down to near freezing,
the heater pads would turn on
and it would save my tanks freezing underneath the van.
Even though those tanks are insulated,
It still just kind of means that the tanks
were definitely not going to freeze.
But I did have it a couple of times where they came on in Scotland.
Those heater pads, they actually draw a huge amount of amperage
and they actually flatten my battery very quickly.
So what I thought was actually I kind of want control over that
because I don't need to turn the waste one
on at the same time as the fresh.
I only need to turn the waste
on if I'm actually going to dump my waste.
The fresh one, I only need to turn it on again for literally like
half an hour, 45 minutes if I do need to heat that tank through.
So I figured the best way to do it
was to actually take them back off of the
Cerbo GX, not have them relay controlled at all,
and just put them on a manual switch,
which is where I installed two switches
on the driver's side just below the steering column.
And then what I can do is just run my engine.
They will run off of the vehicle battery.
I can turn whichever one I want on or both.
And then they actually draw their current from the vehicle battery.
And if I have my engine running at the same time,
I'm not actually losing any amperage.
It's just like turning on, you know, headlights or demist.
It's just going to draw a little bit more
amperage out of the vehicle battery.
And I just thought it was a way better way of doing it.
And then to the right hand side of the steering column,
I actually then put my waste dump
valve and I did it with this kind of little missile switch,
which is kind of cool because
it prevents me then knocking it and accidentally dumping my waste
while driving down the motorway
or something.
Also, there is a really bright light on it,
so if I am about to drive off, that light
is kind of shining right up at me in the driver's position,
so I won't ever forget to turn it
off.
I'll just immediately hit that switch down,
and then, yeah, the valve closes.
And then the only other thing I had to do,
which Kironit Batteries and Solar hooked me
up with, which, mate, I really appreciate
your time on all of this, like, helping me
out.
I'm super grateful.
I actually found out that I had
no more spaces available for my VE Direct cables.
Now, the V-Direct cables, which...
which I've probably shown you in this video
are the data cables which each
component uses to talk to the brain of the system
which is the Servo GX.
But because I was installing another DC-DC charger,
I was actually out of ports on the
Serbo GX, and I needed a way in which
to connect another one of these cables to the system.
So the guys at Batteries
and Solar actually had this VE Direct data cable extension made,
which means that you can plug up to four VE Direct cables into it,
and then you connect
it via a USB-C straight into the Servo GX.
So those guys sent one out to me, and that's exactly how I did mine.
I plugged all of my cables into that.
And then I hid that round the back of the electrics board.
And if you kind of look through the gap where the cables are,
where I've got my Servo GX mounted,
you can just about see all the kind
of flashing lights in the back of it,
where it's kind of working away.
And it also saves me pulling through like another four cables
onto my actual electrics board
and then figuring out where to actually put that.
So it was kind of easier for me just to kind of
tuck it behind the electrics board out of the way.
And then I just had the one USB-C cable coming out of that,
That which goes into a USB.
A cable, I think it is, which then goes into my
Serbo GX. So that's some of the key components on the system,
but like I said earlier in this video,
it really is like drinking through a fire
hose, all this information. If you aren't kind
of in this world and it's maybe your first time converting a van, so
don't let it all overwhelm you. If you do want to dig into it more,
I have created this web page on my website which will give you
all of the specs of the system and literally everything in between.
So like I say, I'll link that below
and then you guys can check that out.
And finally, I just want to give a massive shout out to the partners
that have helped me bring this whole thing to life on this video
and over the last few months.
Number one, Fogstar. You guys are absolute legends.
Jack at Fogstar, if you're watching this,
mate, I really, really appreciate you,
like the time you've given me over the last kind of...
four or five months to work together and kind of bring this to life,
I cannot thank you enough.
So if you guys need lithium batteries,
Fogstar are the number one place in the UK to go and get
your batteries from. So I'll leave a link down
in the description below and I'm very, very proud
to be an ambassador for them and to be able to promote them.
So again, links below and you'll
find them all over my website as well.
Second is Batteries and Solar. Again, absolute legends. I
bought my original kit from Batteries and Solar,
all the kind of original electrical components
Cables and all of the things in between three years ago when I started
building this van and they've been supplying me bits ever since.
So for them to come on board and be a partner as well
and support this project has been absolutely amazing.
So thank you so much, guys. I really, really appreciate it.
Kieran, you're a legend. Thank you, mate.
And last but not least is Evo Design, who actually
supplied all of the original cabinetry in this van.
The whole lot is custom, but they actually
do off-the-shelf kits. And yeah, these guys are absolute legends.
Obviously, I went into full
detail on my whole conversion and all of the cabinetry
when I did my van tour, which I'll
also link below. But if you guys are in the market
for a conversion like mine, they do do
to off-the-shelf kits,
but you can also order custom kits as well.
And yeah, John at Evo Designs was good enough to hook me up
with my battery shelf and a bunch of other stuff that I was trying
to sort out whilst I was doing all the upgrades on the van.
So if you guys want a kick-ass conversion like mine,
head over to Evo Design.
I'll leave a link in the description as well.
And yeah, thank you guys for helping me bring this thing to life.
And last but not least I just want to give
a massive thank you to you guys because
without your support, without you guys watching these videos,
literally jumping in the comments
every single week when I release new videos,
hitting that like button, for all of you subscribing
it genuinely means the world to me.
And being able to partner with these companies and do these
incredible projects, none of this would have
been possible without you guys. So I cannot
I cannot express my gratitude enough.
Thank you so much and yeah, I love you guys.
You're the best.
But like I say, the links for everything are all down below.
There is an absolute ton that I'm probably going to put down there
and you'll also find everything over on my website.
And for whatever reason, if you can't find what you're looking for
or you've got any questions at all,
please drop them in the comments below.
I'll probably be in the comments for a good couple of hours
when this video goes live, so hit me up.
I respond to literally everybody.
It does take me a bit of time,
but I do get round to all of you in the end.
With that said, it's time to wrap this video.
So if you haven't already, maybe consider subscribing.
as it really does help out the channel
and drop this video a like while you're down there
and I will see you guys on the next one. Bye!