How to Weld (Introduction) Motorz #29) #GJWhighonlife #GJWtechnology #GJWtram #GJWadvanceautoparts

Chris Duke
3 followers
Chris introduces you welding with the Handler 140 MIG welder and other accessories from Hobart Welders. Brian Karas guest stars.
BUY: https://amzn.to/3CiwGxO
Show notes: http://www.motorz.tv/blog/1480/learn-how-to-weld/
FOLLOW CHRIS:
https://www.instagram.com/chrisduketv/
https://twitter.com/chrisduketv/
https://chrisduke.tv
FOLLOW MOTORZ:
https://www.motorz.tv/
https://www.instagram.com/motorz/
CHRIS' RECOMMENDED TOOLS:
Products on Amazon: https://chrisduke.tv/amazon
Royalty-free music: https://chrisduke.tv/epidemic
Manage your videos: https://chrisduke.tv/tubebuddy
#GJWhighonlife #GJWtechnology #GJWtram #GJWadvanceautoparts
I'm Chris Duke, and this is MOTORS.
Welcome to MOTORS. Today we're going to cross the automotive customization lines
and teach you the basics of welding and how affordable it can really be.
We're going to cover MIG welding as it's the easiest to begin with, accessories
you're going to need to do the job, basic setup, as well as some safety precautions
and operation. Learning to weld does not require a degree or extensive schooling.
Many people are able to teach themselves how to weld out of their own garage.
My personal friend Brian did just that and is here today to share some tips and tricks
on how to get started with a basic welding setup. Welcome to the show, Brian.
Thanks for being here. Hey, Chris. Thanks for having me. Great. We've got a Hobart Handler 140 right here.
What's the cool thing about this particular MIG welder? Chris, this MIG welder is great.
It's a 115-volt unit. It's very portable, and that means you can run it off of a standard outlet
in your garage, so it's very easy to get started with. That's cool. So, Brian, what sorts of things
can I do with this MIG welder? Well, Chris, this unit is great for automotive and household jobs.
You can do things like basic exhaust repairs, auto body repairs.
You can make custom brackets for mounting horns or fog lights, and it's also good for other
around-the-house jobs, fence repairs, things like that. Okay. Pretty cool.
Let's take a look at some of the things we've got here that are going to help us weld.
Some of the accessories we have here are wire for our MIG welder. We have our MIG pliers.
We have a wire brush and hammer for cleaning up welds when we're done. All right.
We have clamps to hold our pieces together as we're working, and most importantly, our safety helmet.
This one, Brian, is a custom airbrush by Barbara Luck at Ripon Designs. Didn't she do a good job?
She did an awesome job. Now, in addition to all those other things, you're going to need an angle grinder,
some extra tips, some nozzle gel, some gloves, and we've got this paintball cylinder
also from Hobart. It's great for portability, and it just holds CO2,
and it's great because even on weekends, you can get this thing filled up
at your local sporting goods store for about $5. Very nice. Yeah. So let's take a look
at how we set everything up. So we're going to start. First thing here
is we have a spool of wire, and this goes right here
inside the welder. Now, one of the things to be aware
of, this wire is tightly round. If you're not careful when you go to unwind it,
it will unravel and spool up in your face, so you want to have some extra
precaution there. Okay. After mounting and securing
the spool as per the instructions, we're going to begin to feed the wire into our welder.
Be careful as you unspool this so the wire does not come loose.
You want to take off any bent ends on your wire and begin to feed it in.
As you get the wire through the rollers and into the hose,
secure it in place and turn on the welder so we can start to feed it through.
Pull the trigger, and the wire should feed through cleanly.
When it comes out the other end, release the trigger, and you're ready to move on.
Okay, Chris. We've connected the regulator and hose that comes with our
welder to our gas cylinder here. Okay. What kind of gas is in there, Brian?
It's a mix of argon and CO2. Okay. Is it flammable?
Is this thing going to blow up the garage or what? No, it's a completely inert gas.
It's completely safe. Its function is to provide some shielding around the welding arc as we're working.
Okay. Now, what's up with this chart here?
Well, this is really handy. This helps you pick the right wire and polarity settings for whatever
kind of material you're working with. We've gone with a .030
wire today because we're going to be working with some thinner steel like you might find in typical
applications. Okay. What's the polarity over here that I see?
Depending on which wire and gas setup you use, you might change the polarity from electrode
positive to electrode negative. It's just a matter of undoing these two bolts here
and switching the wires around, and the welder lays out which polarity you use
for any given application. Okay. Seems easy enough. Now, there's another thing
here called flux core wire, which you can use without gas
for small jobs. It does get a little bit messy, though. So, Brian, when it comes time to actually
do some welding, can I just wear a t-shirt and some shorts and some flip-flops, or
what's the deal here? Well, Chris, it's important we have the right safety equipment. You're going to want a good
sturdy leather jacket, pair of gloves, as well as you want to make sure you're wearing
something like jeans and some closed-toed shoes or work boots. Okay. So, basically, head-to-toe
coverage. And why is that? Well, there's two important reasons. One, when you're
welding, you'll get some hot slag coming off your welds. There's also UV light on the
arc itself, and you can actually get a sunburn if you're not properly protected. Wow. Sunburn and
hot slag does not sound good to me. So, let's suit up and check this thing out.
All right. Let's get started. Now that we're all suited up, what are the final
steps we need to perform in order to get started and do some welding? All right, Chris, let me show you.
We'll start. We'll turn our welder on.
Come over here. Open up the gas cylinder. You only need about a quarter turn on this.
And we're going to adjust our regulator to get a gas
flow of about between 20 and 30 here on the regulator. You'll see this needle will go
down when we actually start welding. And we're starting with some eighth-inch
thick mild steel. So, we've got our wire feed set to 30, and we're
starting with a voltage of 2. Now, if we come over here, we've already got our
pieces cleaned up and prepared. It's very important when you're doing any MIG welding that you
remove any rust or grease or contaminants on your steel. So, we've already sanded these down
with our angle grinder. We've got a good solid clamp, and our ground is attached here.
And finally, we want to prepare our gun. So,
you don't want to have too much wire stick out when you begin. Usually about 3 eighths
inch to a quarter inch is plenty. So, I'm going to trim off this excess wire before we get
started. Now, all that's left is to put on our welding helmets and give it a try.
All right. Let's go. Okay, Chris. So, we're going to start by just trying a simple
butt weld on these two pieces here. Okay. Now, there's two main ways you can go about this.
There's what's known as a push technique, where, as the name implies, you're pushing
the gun past your weld. Or, more commonly, and what's easier to get started with is a
pull technique, where we're starting up here and kind of pulling the gun as we go along.
So, I'm going to demonstrate a pull technique on these two pieces right here. Okay. Now, do you go
straight back, or do you make a pattern? You want to, as you can see, there's a slight
gap between these. So, you'll see, as I move the gun, we'll be doing small arcs,
kind of tracing the front of our arc and following it along as we
go. We tried to break this weld apart, didn't have any success. That's
a very good indicator that we've picked the right wire speed and voltage settings for the material
we're working with. Okay. Had we actually been able to break this apart, it would have been a good
indication that this was a cold or inferior weld. The wire speed felt
right, so had the weld not stuck, I would have increased the voltage a little bit to get
a little more penetration into the metal. So, it's always good to test it out on
some scrap metal before you work on the real thing. Absolutely. Get a feel for the material
you're working for, get your welder dialed in, and then proceed to your actual work.
All right. Let's try something a little bit thinner, maybe some automotive type of metal.
Okay, Chris. So, here we've got a couple pieces of 16-gauge sheet steel. All right.
Typical of what you might find in an auto body application. Again, we've sanded it clean,
cleaned it up, got it clamped down here. Now, I'm going to start welding this with the same settings we
used on the previous material and see how it works out. All right. Let's go for it.
All right. Let's take a look at what we have with this right here. Looks pretty good from the surface.
Feels pretty sturdy. Take a look at the back. We see here, it looks like that
weld actually penetrated all the way through the steel. Looks like our settings might be a little
too high. So, I'm going to try turning down the voltage on this and moving the wire
speed back a little bit. Okay. Okay. So, we'll go back to the
front panel of our welder here, move the voltage down to one, and then move the
wire speed from 30 down to about 20. So, Brian, what happened
here with this weld? I noticed it really didn't take too well. Yeah. Yeah. Definitely had a trouble,
had some trouble getting the arc started. So, that's a good indication that we
didn't have enough voltage. I think we were right to turn the wire speed down a little bit. So, we'll move the
voltage back up to two, but we'll leave the wire speed back at 20 and see if
we can get this dialed in. All right. Okay. One more try. I'm going to move
this back up right between 20 and 30, and it should be
dialed in now. Yep. I'm happy with the results of how that
turned out. This underscores why it's very important to make sure you do your
test welds on some scrap pieces first. Make sure that you get your settings right before you
start working on your actual project. Well, Brian, that looks pretty cool. I think I've got
enough information now to maybe give it a shot myself. What do you think? I think you do all right,
Chris. Let me give you a couple last-minute pointers, and we'll see how you do. I'm excited to check
this out. So, how does this thing work? How close do I put it, and how fast
do I go? All right. So, this trigger here is what's going to start your arc and feed the
wire. So, we're going to start. You basically want the electrode touching the metal.
Slight arc back. Let the arc start, and then as you're going forward
pulling away, basically just sort of trace the front of the arc as you go along. You'll get a good feel
for the speed, and that's pretty much all there is to it. All right. Let me have at it.
How'd I do, Brian? Let me take a look.
I think for a beginner, Chris, you're off to a very good start. It's actually kind of hard staying online
with the amount of darkness the shade gives you and the arc going,
but I think I did all right.
Brought to you by Hellwig Products. Quality suspension products for over 60 years.
Some manufacturers, like Hobart Welders, are starting to manufacture
and sell custom-looking welding helmets, such as these. Okay, I admit I added
a little bit of extra Motors bling to the front here with this flame, but sometimes
you need something totally custom and out of this world to make it your own.
I wanted that for Motors TV, so I got ahold of Barbara Luck at Rippin' Designs in Utah
and asked her to airbrush something very unique that went along with the show's intro graphics,
and this is what she came up with. As you can see, it's got lightning bolts from
the intro, the Motors logo on the front, and to make it even more badass, she added these blue
flames, per my request, and a whole bunch of skulls to the top. If you look closely
at those skulls, you'll be as impressed as I am with the amount of detail, especially in the teeth.
She'll pretty much airbrush anything, including motorcycles, cars and trucks,
guitars, signs, and, of course, helmets, and her prices are much more reasonable than you think.
For more information, contact Rippin' Designs at RippinDesigns.com.
Well, Brian, thanks for coming out and showing us a little introduction
to welding. I appreciate your time. I did have one more question for you. On a more common
automotive application with, like, some thin sheet metal on a fender or something like that,
is the technique any different? Chris, the basic technique is the same. You're going to want to turn down
the settings on your welder, and you're going to want to basically start with a couple of tack welds and
move back and forth around the piece you're working on so that you don't build up too much heat and warp or distort the
metal in any one area. Okay, cool. So is all the information I learned today enough to start working
on my trailer or something like that? Not quite, Chris. If you're going to want to do something structural, like building a trailer
or working on suspension applications, we'd recommend you take a course at a local Volk Tech College.
Okay, sounds good. Well, that does it for this episode of Motors. For more information on the products
we used in this episode, check out HobartWelders.com. And, of course, for more
episodes of Motors, check out Motors.TV. We'll catch you next time.
Are you ready, Jason? It just sits there. It's great.
He's working hard over there. Now I see why that's such an easy degree to get.
The red one is record.
I did have one question for you that's typical on an automotive
application. Right, right. Spit it out, Chris. I'd be happy to answer it.
Well, this is great for automotive.
We had a custom airbrush by Barbara Luck at Rip and Design. She did a pretty
good job, didn't she? That's an awesome, yeah, I like it.
We have wire for our MIG welder. We have our MIG pliers. We have a wire brush
and our... Bangy thing.
You didn't say action.
Action. Are you going to stand awkwardly in this shot?
I'm going to be around. Should we stand
non-awkwardly? What are we implying here? Okay, Chris, let's start by getting
our welder set up and running. It's very funny, but it's easy to do.
Now, if the wire's kinked on the end, you can
just cut this off with your...
What not to do. Right.
Thank you. We're going to cut off the end of this wire here
and shoot it right into the innards of our welder.
Good God. There it is.
Zoom!
