How to Make an Authentic Crossbow from Scratch

Forging the Past
1 follower
3 Video Views·Jun 25, 2025
Learn how an authentic crossbow is made from scratch and how a Bell's original phone is renovated to ring its bell as loud as it used to ring in the 19th century.
Before there was the rifle, there was the crossbow.
Its earliest recorded use was in China
at the Battle of Maling in 341 BCE,
although historians believe it may have existed
as far back as 6th century BCE.
During the Middle Ages, the crossbow was deemed so barbarous
that the church tried to ban it.
A foot soldier could shoot a bolt from 300 yards away
and penetrate a knight's chain mail.
The crossbow was one of the deadliest weapons
in warfare history.
My name is Mary Ellen Birdwood,
and I make medieval crossbows.
The crossbow she's making today
is based on Count Ulrich von Württemberg's
15th century hunting bow.
Mary Ellen starts by choosing a straight piece of wood
for the body, known as the stock or tiller.
The side profile of the crossbow is traced onto the stock.
Mary Ellen uses a drill press
to make the binding or bridle hole,
the part which the cord goes through
to tie on the bow or prod.
Cavities for the nut and prod socket
have also been carved out using the drill press.
The prod socket is where the bow sits,
and the nut socket houses part of the string release system.
The stock is ready for inletting the bone.
Mary Ellen carves out the depth of the wood
using her homemade router plane.
The bones that will be inlaid here
serve an important purpose for the arrows,
also known as the bolts.
Bone wears better than wood.
Bone is a little slicker, so the bolt will go out faster,
and that's where there's a lot of the pressure
of the string, things whacking,
so it's more durable to have the bone along the top.
Mary Ellen is using camel bone to inlet the stock
because it's easy to acquire.
The original Ulrich was inlaid
with intricately decorated and engraved staghorn and ivory.
The bone is glued and clamped to the stock.
The crossbow is now ready to be shaped.
Top profile template is traced onto the stock,
then cut out with a bandsaw.
In the past, this all would have been done by hand.
A large carpenter rasp removes any marks left by the bandsaw.
A draw knife shapes the edges of the stock.
The most satisfying part is shaping it,
bringing out the lines,
and it's like the bow emerges out of the wood.
Once the stock is shaped,
it's then protected with linseed oil,
which brings out the wood's natural color.
It's time to attach the bow to the end of the stock.
This is called binding or tying in.
Mary Ellen starts by fitting the bow into the prod socket.
She makes sure the bow is centered.
The bow is made by someone else,
but this conforms with historical methods.
Crossbow makers didn't do all the work themselves.
They had guilt, and it wasn't just one guy.
The guy who had the crossbow shop
had people who did the bone carving,
he had people who did the metalwork,
other people made the bolts,
and he brought them all together.
The bridle block is placed on top of the prod
to hold it in place.
Mary Ellen pulls the cord through the bridle hole.
Historically, they would have used a hemp cord like this one.
The cord is wound up and over the prod 15 times on each side.
In between winding, Mary Ellen rolls the cord
onto a pull stick to make it as tight as possible.
Early bows were made of wood and then horn and animal sinew.
By the 17th century, steel bows like this
replaced all other types of bows.
They were water-resistant and less labor-intensive.
Once both sides have been bound,
the stirrup is tied to the prod.
The stirrup is used to cock or ready the crossbow for firing.
Early crossbows didn't have a stirrup
and required the crossbowman to span the bow
by standing on it and pulling the string up.
But Mary Ellen makes hers with a stirrup
because it's more convenient for her clients.
The remaining cord is attached to a flat metal needle
and wound horizontally around the vertical cord
12 to 18 times to tighten everything.
Mary Ellen installs the hand-forged trigger,
also known as the tickler.
She puts in the test pin, which holds everything in place.
Once the trigger is fitted properly,
she'll cut the pin down flush to the stock.
Because the wood could be deformed
by pressure from the string,
Mary Ellen has reinforced the nut socket with bone brackets,
as was done for medieval crossbows.
The crossbow is ready to be strung.
Mary Ellen places the crossbow
on her homemade spanning machine.
A car jack lifts the crossbow
and the bow begins to bend into shape.
In the Middle Ages, they used a spanning machine
to string the crossbow.
It was a big, solid table
that had a screw jack built into it.
They would clamp the bow onto the table
and screw the stock on and bend the bow horizontally
instead of vertically like this.
The string loop is placed onto the bow.
Once it's constructed, it's time to see
if the crossbow is more than just historically accurate.
I just love it.
I can make something that's beautiful.
I've made two bows for museums, period correct.
It's engrossing, it's absorbing, it's amazing
because I get to keep learning and keep doing
and keep expanding.
And I'm lucky that this is the way
that I get to pay the rent.
The most valuable patent ever issued is for the telephone.
On March 7th, 1876, Alexander Graham Bell patented a device
that could transmit audible speech telegraphically.
Three days later, the first ever telephone call was made
and Bell transmitted the words,
Mr. Watson, come here, I want to see you.
By 1888, the American Bell Telephone Company
was already a hundred million dollar corporation
and the pricey patent only got more valuable from there.
My name's Jamie Emerton.
I am the lead phone tech here at Old Phone Works.
This is one of Bell's original phones.
It predates the dial,
so you couldn't call anyone directly.
You had to turn a crank to get the operator
who would then place the call.
Jamie first has to see how well the phones fared
over the years.
The first thing we do is actually
completely disassemble the phone.
With the wood wall phones,
a lot of the problems we have are cracks
or fractures in the wood itself.
A lot of the times the original bells, the dials,
the moving parts are seized and locked together
or they've been exposed to water,
they're damaged, they don't work.
The engine of these phones is called the Magneto,
a hand-cranked electrical generator that rings a bell
when a call is coming through.
The first Magneto was built by French instrument maker,
Épilete Pixie in 1832.
This technology was so sound,
a century later, it can still hold a charge.
So Jamie has to be careful.
Jamie tests the Magneto, the coil, the capacitor.
The phones are so well-built, most parts still work.
Telephones transmit sound by varying the strength
of an electrical current through a wire.
The current is turned back into sound
by the receiver in the phone.
The cloth-covered cord is usually corroded
after all these years.
The more modern coiled telephone cord
only came into use in 1959.
It was made of durable vinyl and designed not to tangle.
But for these old phones, cloth is king.
In the shop, Jamie uses an original braiding machine
from the 1800s to make a new one.
Using a rotary buffing station,
he removes a century of dirt and grime from the handset.
He then sands,
stains,
and then puts it all back together again.
With a quick crank of the handle,
the phone is in working order,
just as it would look and sound
in Alexander Graham Bell's time.
And it's only taken two days.
