How To Install Cabinet Handles - Amazing 20 Bathroom Upgrade

The BeefMaster
118 followers
2 Video Views·Dec 11, 2022
In this video I'm going to show you how I updated these old bathroom cabinets
on a $20 budget. Let's get started.
These cabinets could use a lot of love and tender care. They're very plain and bare so
to improve their look we're going to add cabinet handles. The first step is to remove these drawers
and I'm going to remove both the large and the small ones. Now that they're removed I need to
get the right measurements for the handles. One of the best ways to do it is to first measure the
handle itself, but make sure you do the inside where the screws are, not the outside of the
handle. In this case it's about 5 inches from the center of each hole. Next I estimate where I want
to place the handle, then get a tape measure to get it exact. The front of this cabinet is about
9 and 7 eighths inches wide. I then half the distance to get the center, which is just under
5 inches. I then go 2 and a half inches from the center on the right and left side to get a total
of 5 inches. To get it square I measure the width which is 5 and a quarter inches, so halfway is 2
and 5 eighths. I mark that on both the right and left side, and now we have our drill points for
the handle. That may have sounded complex, but all you're doing is dividing the length of the handle
in half, then go that distance from the center of the drawer. With those measured and drilled out,
I now place the bolts to hold down the handle. If you have any marks or measurements,
now is a good time to clean them before you secure the handle. Depending on your setup,
you may want to have these fairly tight, but to avoid damaging the wood I only used a screwdriver.
That's very secure, so let's work on the big drawers. For the big drawer I repeat the same
process. The center is just under 8 inches, and I go 2 and a half inches on the left and right,
because the handle is 5 inches wide. The large drawer is the same width as the small drawers,
so I make a mark at the same location. Even though the markings are the same,
it's always good to double check and make sure it fits correctly. Everything lines up,
so let's drill the holes. It's a good time to clean out the drawer and wipe off any dust
and dirt. With the handles done, let's go put them back and see how they look.
So far it's looking very good, and everything's lined up straight. The next step is to put the
handles on the cabinet doors. I'm going to start by again estimating where I think it looks good,
then we'll get the tape measure to make sure it's exact on both sides. I decided to go 2 inches from
the top and made a mark on both sides. I made the bottom mark at 7 inches as the handle is 5 inches
long. To square it up, I went over 1 and a quarter inch to make the drill marks. As a tip, when
drilling it in, make sure to open the door so you don't accidentally drill into the back piece.
With those holes made, I clean them off, then put on the handles. Same process as before,
slide in the bolts and tighten them down. The cabinet drawer handles are square and look good.
With those done, the next step is to put a handle on the fake drawer front. Again,
the process starts by measuring the width, which is 16 inches, so halfway would be 8 inches.
Again, the handles are the same length, so I go over 2 and a half inches from the middle
and make a mark. The width of the false drawer is the same, so I make a mark at 2 and 5 eighths.
Now note that your drawers are of course going to be different sizes, just make sure to find
the middle width and length correctly and everything will be square. Drill the holes,
then clean off the dust, put the screws through the back, and then tighten the handle. The sink
was in the way, so as a tip, you can turn the handles like this if the screwdriver doesn't fit.
After tightening it down, give it a test pull, and we're done here. These handles were only $17,
but greatly improved the look of these vanity cabinets. They're very straight and durable,
and they changed an old bathroom like this into something much better.
This is the second video in a bathroom update series. If you'd like to see other inexpensive
updates I made, I'll have those videos linked below. Thanks so much for watching, and have a
great day.
