How To Install A New Kitchen Sink, Faucet, and Drain, DIY Plumbing

The Stone Cube
31 followers
26 Video Views·Nov 3, 2022
How To Install A New Kitchen Sink, Faucet, and Drain, DIY Plumbing
Hey everybody welcome back to my channel. Today I'm going to show you how I installed this sink,
this faucet, and hooked up all the plumbing to it. So stay tuned and check it out.
All right so real quickly I want to just state that I'm by no means a plumber,
but I do feel comfortable installing this sink and hooking up the plumbing. If you guys don't
feel comfortable doing that by all means hire somebody else to do it, but like I said I feel
comfortable doing it and I hope that at the very least you gain a little bit of knowledge from this
video. So with that being said let's get started. All right so I've got a very straightforward
sink right here. It's just a drop-in stainless steel sink and I'm just going to drop it in the
hole and just make sure it's centered in the hole. And if the hole for your sink in the countertop is
cut out correctly there's not going to be a hole out of play. So I've got center right about there
and then I can go ahead and tape along the outside edge of this sink. So like I said just kind of go
around and outline the sink. All right so once you've got your sink outlined with tape you can
go ahead and pull the sink back out. Then I'm going to take some 100% silicone. I just went
with clear and I'm going to make a bead all around the countertop hole. So I'm going to be
not on the tape obviously but just inside of the tape right along that edge. Now you don't want a
ton because you don't want a ton of it squeezing out, but you know you still want to seal it down.
So just get maybe a good like quarter inch bead going here. All right so the tape has two purposes.
The first is to help clean up any of the silicone that squeezes out the front edge or any of the
edges for that matter. And the second is to help you line up the sink once again.
So once you got that bead of silicone just drop the sink in place using the tape as kind of a guide.
There you go. If you want you can put a little bit of weight on it but don't put too much because
you don't want to crack your countertop either. And then you can pull up the tape while the
silicone is still wet. And then your sink will most likely come with some of these clips like this.
So there's just these two pieces. This piece up here goes into a little groove on the underside
of the sink and then this piece right here tightens up against the countertop. So like I said
just put this brass colored end up into the track of the sink. Just slides in the end there and then
I can tighten this up to this MDF backing on the countertop. There just like that. All right so in
order to hook up the p-trap to this drain outlet I'll have to add a couple more pieces. So the
first piece is going to be a coupler piece. So that's just going to slip on right like that and
then the second piece is going to be this trap adapter and it looks like that. So let me go ahead
and cement those in place. For that I'm going to be using the pvc primer and cement. Let's go ahead
and prime both pieces and then add the pvc cement both sides just the same. And then stick this on
here and kind of give it a little bit of a turn as you do. So there is
there is a lip on the inside of this coupling piece so be sure to push this coupling piece
all the way on until it's seated right at that lip. And push that in and kind of give it a little
bit of a twist as you're pushing it in. Make sure it's seated all the way back and just kind of hold
that in place for it says 30 seconds. I don't know if it takes that long. All right then we can go
ahead and install the sink basket in place. So to do so just take off this nut. This nut's going to
hold on the tail piece later on so just set that aside. Then next we got this nut. Take that off
and that holds in this deep cup right here and then it also holds on this rubber gasket. And
what you're left with is this I guess basket right here. So what we got to do is we got to
put some plumber's putty along the underside of this flange right here and then stick that down
in the hole and seal that in place. So let me show you. All right so go ahead and pick up some
of this plumber's putty right here. It just comes in this little tub right like this. Take the cover
off and just grab a chunk of it. All right and then just roll it in your hands and kind of make
a snake out of it. Roll it on the countertop if you need to. Just make sure that it's somewhat
uniform in diameter across the whole thing. All right that's looking pretty good. Then take your
strainer basket set that upside down like this and just wrap that along that flange
until you overlap like that and just stick that down like that. Perfect. Now we can go ahead and
throw this in the bottom of the sink. All right so just take that and put that right in the bottom
of the sink and just press down a little bit. Probably have some squeeze out. One thing again
to realize is that where your sink was cut into your countertop is going to be the weakest point
in your countertop. So as you're pushing this down don't like don't put all your weight on it by any
means. Just push it down until it's seated in there and then we can screw the nuts on from
the underside and that's going to just sandwich the sink base between all those pieces. So that's
going to take out any more of the slack around here and then you can kind of just trim back
whatever extra plumber's putty there might be. All right so now we're under the sink and you can see
that a little bit of the plumber's putty is coming out under here. It's totally fine. I'm just going
to take away some of the excess and then we can install this bottom nut. So first thing put the
gasket in place. Then we can put this cup underneath here and then finally we can install
the nut that holds all of that up to the underside of the sink and just take a wrench and snug that
up. All right there we go and then once you tighten up that nut from the bottom you'll probably notice
a little bit more of the plumber's putty squeezing out from the top. So just take away any excess of
that and you can go ahead and put this right back in that tub to use again. All right then I can
start assembling the tailpiece and the p-trap together just to see. I'm sure I'm going to have
to cut this down in size so I want to assemble this just dry and see how long this piece needs
to be. So this is just a tailpiece. I believe this is 12 inches long and then this is a p-trap kit
that I picked up at a big box store. Links to everything is going to be down in the video
description if you guys are looking for any of the specific pieces or the tools that I'm using.
So let me go ahead and assemble this. Basically this piece is going to go into the wall so this
end is going to go into the wall like that. I'll thread this nut on here and I'll connect it with
the rest of the p-trap like this. All right so that's looking like that and then the tailpiece
can come down from the the basket that we just installed and that's going to sit in here and
then tighten onto here. There's a little red gasket that goes in there to hold it in place.
One thing to kind of take note on is this. So one thing to kind of take note is that this
tailpiece is going to want to sit all the way to the bottom of this little flare out right here.
So if you take this out it's going to sit all the way down there. So if you do need to trim
your tailpiece back at all make sure that you have it seated all the way down and you can
take this dimension into consideration. All right so take the nut that's on this trap adapter off,
slide it onto the end of the p-trap and push the p-trap into the wall until it bottoms out
and then just kind of hand tighten this nut on for right now. We're just kind of getting a
general dimension. All right so that's like that. Then we can take this other nut in this little
gasket that were on the underside of this basket. We'll take the gasket here put it on the flange
side of the tailpiece and then thread the nut up from the bottom and just kind of put that in place.
We'll tighten that up until it's snug as well. All right and then we can see here let me get a
little different angle. All right so we can see here that we got to cut this tailpiece off right
in line with this flange. So I'm actually going to cut it just a hair shorter so that when it's
all assembled this shortened tailpiece will actually pull this p-trap up just a little bit
so that I get positive drainage going back into the wall. So let me just mark this out where I
need to cut it right about there and then I'm just going to take a hacksaw and cut this straight.
So we just cut this tailpiece off let's see how that fits. So put it in there bottom it out right
there and we are looking pretty good. You can throw a level back here just to kind of see if we got
positive drainage towards the wall and it looks like we do. So now it's time to go ahead and
assemble this for real. Let's take this off. All right so take this plastic piece put it on top
of the tailpiece. We'll thread this nut up from the bottom and then we'll put this on here tighten
both of these up a little bit. There we go. Let's take this off here. Actually I don't trust it just
plastic on plastic so I'm going to add a little bit of teflon tape and teflon tape goes on
clockwise. So we got the teflon tape on this side and that's going to go up here we'll slide this
nut down here and tighten it up but before we do that we'll take this other nut slide it up here
we'll take this little gasket right here put it on the end slide that up a little bit
right there we'll take now we'll take this p-trap piece right here we'll push it up onto the
tailpiece until the tailpiece bottoms out on this little flange here and then we can just slide that
gasket down a little bit here and then we can tighten up the nut that can just be hand tight
for right now then see right there you can tighten we'll loosen this up just a little bit because I
got to push this pipe into the wall just a little bit more all right then we'll slide this nut down
and we'll tighten up this joint right here nice and we can just kind of push this in or out of the
wall until it kind of gets to that equilibrium spot where it's not just jammed into the wall
but it's not hanging loose and then we can tighten this nut back here all right so those
are all hand tightened on there I think it's looking pretty good all right we got the drain
done all right then I can go ahead and install the faucet so I picked up this faucet from American
Standard it comes with a soap dispenser that's very easy to install and actually the faucet is
very easy to install as well so let me show you all right so I've got the four holes in the top
of the sink this hole that's where the soap dispenser is going to go and then I'm going to
thread the lines for the faucet through this middle hole and then the plate is going to cover these
two outer holes so I'll take the lines for the faucet and I'll just feed them through the center
hole so then to lock that in place we've got a nut and we've got a steel washer a rubber gasket
and then a threaded nut that we can install from the underside so we've got the rubber gasket we've
got the steel washer and then we got this threaded piece right here so we'll just thread our lines
through all three of those and then we can just tighten up the threads so basically you tighten
that up hand tight and then you come back with a screwdriver or a drill and then tighten these
screws up until they're snug similar thing with the soap dispenser make sure that you put the
rubber gasket between the two metal pieces so this metal piece and the sink top put that on
and then the rest of this threads up from underneath again
then I can go ahead and hook up the water lines here so I think you can see that on camera this
line has a little blue stripe this one has a little red stripe so that's pretty helpful
and the way that I remember which is which hot and cold on here is a song by E40 I don't remember
the name of it but in the song he claims that he's hot like the left sink handle so I always
remember that the left side is the hot side so it looks like my plumber had this not here and then
there's also this brass bushing here the ends of the supply line I don't know if you can see that
but they've got a little rubber gasket in there already so I don't need any of that stuff so
I'll just kind of loop this line around and thread that on here I got it hand tight and then
let's give it a little bit of a turn with a wrench so we are dealing with plastic lines this
PEX line here so that's why I don't really like to crank on these things too much
just get it tight like that all right same thing with the cold line kind of loop that around
probably wondering what the heck this line is well this gets connected together and then this is the
line for the pull-out faucet like this but we have to add this weight to it to do that we'll just
loosen up these screws on either side and then we can kind of feed it onto the line like this
and they've actually have it marked out down here where you should center the weight tighten the
screws down feed this up through here push this push this piece up and then bring it back down
and that clips it in place so let me show you that again so bring this clip up push this end into it
and then bring this clip down that's going to secure it in place and now when I pull on the
faucet handle up there like that allows it to do that and then this weight
brings it back down all right now for the moment of truth let's turn on the water
and see if it works all right here goes nothing sweet all right so visually I don't see anything
leaking right now um but you know it may take a little bit of time if there were to be a leak
for it to start to drip out in the meantime what I like to do is just take a piece of cardboard
and just lay it down underneath it reason for cardboard is it's just very obvious if there
were to be a drip that appears on here be very obvious that you would see it oh and I almost
forgot to check the soap so you might take a little bit just to prime it there we go and if
you guys enjoyed this video it would be awesome if you could hit that like button down below
that just tells youtube that this was a decent video and that maybe it should pass it on to some
other people to watch and if you're not already subscribed it would be awesome if you could hit
that subscribe button as well that way you're notified every time I release a new video
and until next time thanks for watching
