GELADEIRA FOST FREE PAROU DE GELAR!
Jan 31, 2024
inscreva-se no nosso canal e ative o sininho 👍👍👍👍
siga-me nas redes sociais... https://instagram.com/rodrigo_ferreira3049?igshid=biv26p1qygf8 https://www.
facebook.com/profile.php?id=100039938894421
Torne-se um dos nossos alunos
Deseja se tornar um profissional da refrigeração acesse o nosso site 👉https://recursosderefrigeracao.com/
✅ aprenda tudo sobre ar condicionado comigo *️⃣👷 cadastre- se agora 👇 https://recursosderefrigeracao.com/ar-condicionado/
✅ seja um profissional qualificado em manutenção de tanques de leite 🐮🔧 participe agora 👇 https://recursosderefrigeracao.com/tanque-de-leite-2/
Hello everyone, I'm Rodrigo from the refrigeration resource,
welcome everyone to another video here on the
channel, in today's video I came to bring
you a very cool tip about
a foss free refrigerator that wasn't
freezing underneath, but this one The refrigerator is
a novel, guys, as you can see
here, the interface plate is
deactivated, we have the other
plate up there because
its problem was not so simple to
find, okay, so I'm going to talk here a
little about what was happening, what It has already been
replaced and what are we going to
replace now, great, so let's go to the
video, guys, this is the
Eletrolux Force free refrigerator, this is
a
df46, as you can see,
here it is without the panel, which
we disconnected, we dismantled the panel
to observe this Here, look, it's like you're
sweating a lot, you see, the interface board has
already been replaced a few times. This
problem is chronic with this model of
refrigerator. Everyone has this model of
refrigerator. Every now and then, you have to
change this board because of this
little problem. we
put it to work with a
new interface plate at the top here so we can
continue with the tests What was the
initial problem with this fridge guys
stopped working everything didn't work not
even the freezer didn't work nor the
fridge
we evaluated it so it had to be
replaced of the power module that
is behind the refrigerator we replaced the
module we put it to work then we
had this problem here I'm going to
disconnect it
here open it here for you to see Where is the
defrost guys so looking quickly
here we see that the evaporator was not
defrosting We checked the sensory network,
everything was OK, so what did we do before
sending it to the
customer, we checked that
its interface board was bad and here guys there
is a little problem that this refrigerator,
its temperature sensor also passes
through the interface board, that is, if the
interface board is very bad, it can
also cause the problem that
we did, so we replaced the interface board,
we put a new interface board
here in front, it's giving an error because
we disconnected the sensor network, it
identified the fault, but even with the
board
new interface still didn't do the defrosting And then
guys the problem comes,
everything is working resistance giving
resistance value temperature sensor
new interface board new module and why does
n't it do the defrosting guys Oh the answer
here oh already there oh oh oh So we're going to need
to replace the defrost resistance
Why is the defrost resistance
heating up but it's weak, so
when you activate the defrost it takes a
much longer time to be able to melt all
the ice in the evaporator, in other words the
module ends up turning off the relay of defrosting
before the defrosting is actually
finished because it gives the timeout it
starts working again Rodrigo how do
we find out about this guys generally
when we go to test a
resistance like this What do we do
we take the multimeter and put it there in
continuity, measure the resistance, if
applicable, put energy into it and wait for it
to heat up completely and it was no different. In this case,
we did all these tests too and, at
first, identifying, saying no, the
resistance, I believe it's good, however, that's why
I like to leave it the
refrigerator has been tested for a long time in the
workshop, guys, when we have
this type of doubt Only after
several days of testing here
can we be sure that the problem was
really the one we
identified So let's go here for you to
see So guys, look for those who are just
starting out, just so you can
get your bearings, this is the evaporator, this
is responsible for freezing the entire
refrigerator, how does this
entire piece here work, it freezes, the fan
circulates the air, makes the air pass through here
inside and distributes the air cold,
right?
we have the
thickest pipe here, it's all
covered in ice, the thickest pipe is
the evaporation pipe, right where
the refrigerant fluid circulates, evaporating
and removing heat from the environment and here
we have the
Resistance pipe, right, this resistance here
is This thinner tube heats up
so what's going on to melt all this ice? So what's
going on here
guys, if we stop to analyze and look closely, we
can see a difference in the ice,
right? not this part here,
so if we stop to
analyze it, imagine that this little tube here
heated up at some point, the ice melted,
the ice flowed down here, you can see it, if
you look further away it becomes more
noticeable, oh, so this part here,
oh There was even a defrost, but there wasn't
time for it to melt completely and the
refrigerator was already working
again. So you arrived at
your client's house, opened the evaporator,
identified this here, it means that the
refrigerator is starting with ice, but the
resistance does not have
enough capacity anymore. of melting the entire
evaporator in time and the refrigerator
starts working again And then you keep making
these layers here, you see, so
this here, this part here we can
say, oh, that it never melted, oh, when
we are testing this part here Oh, it
never melted, just this part here, it
got to the point of doing the
desilo And now I doubt you can guess
what the solution is to change the
Resistance, guys, do you want to learn how to
change this resistance in this
refrigerator, here in the video that
we now Let's get our hands dirty, guys,
so the first step here is to make the
ice, guys. So we have two
options to do the defrosting or we can
do it the simplest and quickest way, which
is literally pouring water, you can
throw water one a little warm, you can
add natural water or we can
come here and disconnect the resistance and
set it to 110 or 220 depending on what is
happening, but if the resistance
is weak it will take a long time and the
quickest way is to add water, okay, you can
play lukewarm water or you can pour
natural water, it will depend on what
you have on hand and your
rush. Remembering that if you are going to throw water
or if you are going to heat it up suddenly with a
hairdryer, something like that, right here,
folks, there is the thermal fuse
thermal fuse if it heats up you will burn out And then the
refrigerator doesn't defrost either So you
have to be very careful when
defrosting with this component, well,
good guys, so here, defrosting
completed is even easier for us to
identify here, piping This thin
defrost resistance, the thicker pipe
is the evaporation pipe, right,
our evaporator, so what do we
do here, we have two
Philips screws, one here and the other there, which
we have already removed to advance here,
so we will remove the
thermal fuse this little Yellow wire Here it's from the
sensor it's stuck right below this
white one here it's from the resistance of the gutter
this one you don't need to pull it it
's stuck down here it won't come out that's it
done what are we going to
do we're going to come here and pull the
evaporator up, we're going to remove this zopor
here, we're going to pull the evaporator
up, it's going to come, if it doesn't come right away
with your hand, it's just difficult,
right? There is
ice because sometimes there can be ice
down here and the ice stops it from
rising then you melt it, you see, it started
to rise, then it's certain that there must still
be a little more ice there, you
remove all the ice and pull it upwards.
Guys, detail here is a very
important tip, see this one, the ideal
is for you to pull it by holding it here,
because sometimes it gets stuck down here
when you pull it, it goes up all at once,
right, if you're not holding it, this could
happen with this aluminum pipe. you can
see that here it is stuck It could
happen that when you pull it out it gets stuck
here and then when you
undo it it breaks here and leaks the
gas. So if you hold it here it will be
normal for it to make a ripple in the
pipe, but the ideal is If it is
done in this part here, because here it
will be more gentle, you won't run
the risk of the pipe breaking, so
always hold it here when pulling the
beauty and also be careful with this turn
here so as not to cause a leak here, ok
Sometimes You're going to replace a
resistance, if there's a gas leak, it
's your responsibility and then you're in a
mess, okay guys, here, we've
already done the process, so, right, it went up there,
as you can see here, I bent it
a little here. right out so
that this part here would have space to
go in behind it, that makes it easier.
So when we lift the
evaporator here, now guys, we
're going to cut it.
we take out the
sensors and so on so it doesn't get banged up
And then here, turn it over So you
understand
better, here, where it's stuck, you
can pull it and it will come out, if it
doesn't want to come out, you come here, give it a
slight bend
[Music]
See, take this side off, then take off
the back side there too. Once you've
removed everything, it will come out from below
here and the new one, we'll position it in the
same way, guys, here, I removed
the old resistance. Look,
you can see. how is it divided, this
layer here in my hand is
the layer at the back, right?
it stays
here
like this, we release it all, it comes out from
below and now we're going to put the
new resistance in place. Look
guys, this one here is the new resistance, in
this case, guys, because of the
price, the customer opted for the
parallel resistance, you can see that It has
some differences, I'm going to take it out of the
bag here so you can see, look
guys, the main difference is in the
gauge of the tub, this one is a
little thicker, there's a connector here,
it also doesn't come with a direct connector,
right, but it comes with the pins. male
here from Chapinha, right, so with a little
adaptation we can get it
to work normally Well, if it's
an original resistance, everything comes in the
perfect shape, but then, as they say, it's
the customer who determines, right? The important thing
is that we have the options. to be
offering to the customer to serve all
types of customers regardless of the
options that the customer chooses in this case, right,
so here now I'm going to take out this
little ribbon that's here in the middle and we
're going to divide it in the same way so we can
observe it come here, always two
layers, you see, the one will be at the back and the one
will be at the front, we open
it Put it underneath here and we will make the
fixings Look,
guys, we need to make some
adaptations So, but resistance already
positioned front part
back what's the wiring, we'll make
the connections later and here we
secured it with the nylon clamps here
guys, where will it fit?
you
come and cut the edges and make room
for the resistance to fit in there,
great, now we're going to position it
in place again and we're going to make the
connections. I'll show you how it
's done, good guys, in the rush,
I almost forgot that I was
recording for you, right? So let's go,
reposition everything in its place, here it is And here,
how do we make the connections?
See how the male pin already comes, I just
applied some tape just to make it well insulated
and we connected it again to the place,
hold everything together nicely here with
zipper tape and it's ready now we put it on
to test the resistance, I already heated it
once to see if everything was
ok and now we come here and
close it
again there,
reposition this fairing together with the The
fan motor always checks if it
's compatible with the hole at the bottom,
okay, and here guys, now this
refrigerator, I'm going to let it test
again to see if everything will be
ok here, okay, so everything's connected,
nice, I'm going to let it work
like this here and then the We'll evaluate
tomorrow whether it's already defrosted, how it
's ok guys, so this is how
we replace a
resistance in the refrigerator Foss Free
Eletrolux Rodrigo This way of making
the change works for any Foss
Free model, it works guys, the principle The basics are the
same as what you'll have to see. That's what
you'll need, right, for each model.
Sometimes you need to make an adjustment here and
there. Finally, get it working,
great, like I gave you this
refrigerator, we're going to put it to the
test now. and probably in another
day or two we will deliver it to the
client Rodrigo Why do you like
to spend all this time testing for
me to make sure what the problem is
Rodrigo your client so you are left without a
fridge don't you guys we always
need it staying in the workshop for so long,
we take a fridge to the
customer when we pick it up from him.
Okay, so we leave one Wow, a
simple fridge and such to
lend to the customer, bring the customer's
to the workshop And then we have all the
time world to provide that service
with that quality that we like
Alright now I wanted to remind you that you
are looking for knowledge you want to become
a qualified
professional professional courses and everything else we
always have something
check it out Here below at the time of
recording this video the air
conditioning formula and the milk tank formula
are available the links to the
training you will find here
below in the video description and in the
pinned comment beauty Oh don't forget
to follow me there on our social networks
beauty the links will also go everyone being
down here, we're together guys,
that's all for today. Stay with God everyone and see you
next time.

