Forging a Sword (Part 4): Linishing and Quillons

Forging the Past
1 follower
5 Video Views·Sep 2, 2025
The forging of Arnander, my English bastard sword, continues. In this episode, I begin linishing—grinding and polishing the blade—and craft the quillons (crossguard) with a touch of flair.
A more experienced smith might have better judged how far the quillons would extend when hammered out, reducing the need for heavy grinding. In medieval times, without motorised tools, smiths aimed to minimise this step as much as possible.
Meanwhile, back in Glastonbury, the forging of Arnanda continued.
Now to grind the fuller, and there are a couple of ways of doing this,
but I've been told that using this machine is the easier of the two,
so I've picked this one.
Big loud noise.
And now, linishing.
This is linisher, with which I shall linish.
It's a big sanding belt,
and then first thing I'm going to do is I'm going to take off
the very, very slight wobbly edge
and try to straighten the profile down both sides.
Wish me luck.
What I've done now is I've straightened up the two edges.
One of them came nice and straight very easily.
The other one, though, had a bit of an outward curve in it,
so it required removing a fair bit of metal,
but it seems to be decently straight now.
So now I want to put the profile on this.
I'm not going to take it all the way to the central ridge yet,
but I'm going to try to take all the hammer marks
that I put on the bevels either side off.
Oh, whoops.
I'd been distracted by my own piece to camera
and gone back to the way I'd been holding the sword before.
Had I continued I would have got a hollow grind.
The correct way to hold the sword for this stage is upright, like this.
Unfortunately, in the confusion,
my cameraman pressed the record button twice,
so there is no footage of my excellent linishing.
Which is a shame, because it was my greatest skill.
It's the end of day three,
although today's been a very short and comparatively light day.
I've not been doing any forging or anything,
so there's been not a lot of heat involved,
although I did have to stop a couple of times
because this was overheating the sword,
and I can feel it through my gloves.
Right, so this is the stage I've got it to on the linisher so far.
I've been keeping away from the central ridge.
That's the last bit, tricky bit, to put in down the centre.
You can see though, on this side,
the central ridge has just started to form,
which was my signal to stop.
On this side, I've probably done a better thing
and left a little bit more to work with on this central ridge.
So the finishing gate is in sight now on the blade.
A bit more grinding will finish off the central ridge.
There's the grinding on the fuller to be done,
most of which is going to be done by Tom,
because it's become plain to me
that it's actually really pretty tricky,
and then we have to put an edge on it.
It's going to be sharp.
We did wonder about whether to make a blunt sword,
whether it should be a sword that looks as though it's sharp,
but isn't really.
There are advantages of that.
It'd be quite nice, for instance,
if I'm at some event,
to be able to hand my sword to a member of the public,
knowing that it's not sharp.
But Tom and I eventually decided that, no,
what we should be making is a real sword,
a real authentic sword.
If it's not going to be used for haemorrh,
if it's not going to be used for sparring,
it's not, largely because, you know,
I've made this, I've gone to a lot of effort,
and I don't want to then wreck it.
It's going to be a real sword,
so it's going to be sharp.
There is talk of passing laws in Britain,
making it illegal to sell people sharp swords,
but you can still make your own sharp swords.
They're not saying that's going to be legal.
So I think this will be one way to get a sharp sword,
will be to make it yourself.
So it feels like a sword.
And I'm really happy with this length.
It feels a really good length.
I think I might keep a lot of this tang, actually.
The current plan is to put a fishtail pommel on.
So that means that you can grip on the pommel
with the offhand, the left hand.
And I think I'm going to go for quite a simple,
straight cross guard,
but maybe just to be a little bit fancy,
put a couple of twists in it,
maybe a little end nodule,
just to, you know, have something to look at.
So end of day three.
I'm happy.
This feels like a sword now,
and it even looks, I hope you agree,
quite like a sword.
Tom and I have just had the quillon conversation.
So the cross guard, made of two quillons,
is going to be made out of this lump of square,
quite substantial metal.
This is as thick as probably the very thickest part
that the cross guard is going to be.
We've just marked on three dents in it
to show us where the hole that's going to take the tang
for the blade going through there will be,
and where the edges of the depression
that the shoulders of the blade go into will be.
So it's going to be essentially there.
And then this is going to have to be lengthened.
And I've decided to get a little bit fancy
and put in some twists.
But in order for those twists to show up nicely,
give us the so-called barleycorn effect,
we're going to leave a square section
so that those twists show.
And then I'd quite like the ends of the quillons
to be rounded, to have a globe at the end,
rondels if you like, roundels.
Because I like the quillons to be blunt,
because they're going to be there,
I'm going to be walking around with them,
and things are going to be catching on them.
And if they're square and spiky,
I'm going to get my cloak snagged on them and so forth.
So a nice rounded end to the quillons
will be a very comfortable way of carrying on.
Now, we've also had the conversation
about what size should the entire thing be.
Now, this is going to be a bastard sword.
And a hand goes there up against the quillons.
And don't forget that we've got to take into account
the fact that it's going to be wearing gauntlets.
So my hands will be slightly bigger,
though exactly how much bigger, we don't really know.
And the other hand is going to be gripping
on the end of the grip plus the pommel.
And of course, you can actually put the fat part of the pommel
into the center of the lower hand
and use the sword that way.
How much room should we leave?
It's all a matter of judgment.
Another question is whether to have a widening in the grip.
Some have a wider bit looking something like that.
And if so, where should that go?
Should it go at the bottom of the right hand
to stop your hand sliding down the grip,
acting, if you like, a bit like a pommel?
Or should it perhaps go in the middle of the hand
so your fingers can grip around that?
But again, that does the same job.
It helps you grip the sword and stops the sword
sliding accidentally through your fingers.
So that's another issue.
So there's something blocking the airflow
and the fire's got a bit cold.
So I can feel something in there
and it's a clinker.
This isn't cold.
It's like molten metal.
I have to put that back in.
And yeah, quite a small one.
I thought it was bigger.
But yeah, that.
Eventually, you fill a bin with the stuff.
I have here two blades.
This one will be mine
and I've done most of the work on it.
And this one was the one that Tom used
to demonstrate to me what I needed to do
to make this one.
But Tom will be ending up with this one
and he didn't want a bastard sword
the same length as mine.
So he made his very slightly longer.
Can you see?
It's all of about three inches longer.
And here's the weird thing.
It's only three inches longer
and yet it's a completely different weapon.
And I could see right from the start
that it was a different weapon.
When he was the other side of the workshop
picking up one of these swords,
I could tell immediately that he had picked up his own
because it just looked so huge.
This is a longsword.
And when I hold it,
admittedly it doesn't have its grip on it yet,
but I can hold the tang.
When I hold it, this feels like a longsword.
No way would I want to use this in one hand.
It's, to me, this is really slow and awkward
and hurts my wrist.
This is a longsword, absolutely.
And we've been looking at it
and we both agreed that extending the fuller on this
would somehow just suit this blade.
It's a different blade.
It feels different in the hand.
This one, this is what I asked for.
I wanted a bastard sword
and this feels in my hand like a bastard sword.
It's only three inches shorter,
but it handles quite differently.
The fuller ends here.
This is a Type 18.
It's got the straight sides.
That one's got a very slight curve on it,
which strictly speaking means it's not a Type 18 anymore.
It is an extraordinary thing.
As soon as I see a weapon like this in someone's hand,
I can see what his reach is,
which is a very important thing
when you're trying to judge an opponent.
How can he get me?
Am I within his measure?
So when he's standing here,
it's not just the length of the blade.
You've also got to take into account the length of his arms
and what sort of footwork technique he's likely to use.
And yes, as soon as I saw this,
in someone's hands,
even from a distance,
yep, it's not a long sword.
This is a bastard sword.
And it's one of those weird things
that's extremely difficult to define.
There is no absolute cutoff point.
You cannot say a sword such and such a length is a bastard sword,
but if it's three inches longer,
that makes it a long sword.
And yet when you handle an individual sword,
you feel it in your hand.
You feel its balance.
You very often can tell.
And with this, I'm much happier using this in one hand.
This doesn't hurt anything like as much.
And if I got right up to you,
start half-swording you,
I feel much more able to use this
in the bastard sword fashion.
So yeah, I've made a bastard sword.
I've got this and this standing by
to put the shoulder slot in.
Tom is ready with the tongs.
This is a critical stage.
If I put this in the wrong place,
we'll have wasted a piece of metal,
which will be a shame.
What do you reckon?
Oh, it's decently central.
It's pretty good.
I don't know how well you can see this,
but there's a little nick in the centre of this tool here,
which will mark the centre of the hole,
which I'm going to have to punch later.
So I'll have to see the tiny little indentation left
in the hot metal
and judge the centre of that by eye
for putting the hole through the middle for the blade.
A couple more, all right.
Yeah, I think that's good.
Okay, we have our shoulder slot.
So now I put down this and pick up this.
This will put the hole all the way through for the blade.
And you see it goes straight for a bit
and then it widens out.
So I'm going to have to hammer all the way through
to put a hole in
and then go a little bit further
to create a bit of a widening
which will accommodate the width of the tang.
It's a little bit approximate.
I've been told that it's best to go not quite far enough
so that the blade is too tight
rather than to go too far
so that the blade is too loose in the quillons
because tightening it up is a swine.
I can't see it.
That looks like about the middle.
Yeah, you want it there, yeah.
Whoops, that didn't sound good.
Nice one.
Yeah, that's good.
With this one, we're going to put it over the hardy hole.
That's the larger square one.
And then I'm going to try to bash all the way through to daylight.
Oh, no, no.
Enough or not.
That's quite clearly through.
Is that about as deep as you want?
That's fine.
Okay, right.
Okay, so now we have a hole for the tang
and a slot for the shoulder of the blade.
Before risking the application of my incompetence on my cross guard,
I practiced putting a spherical end on a piece of scrap steel.
Pretty good.
Okay, seems I can do it then.
Now to show that it was a fluke.
Now to work the precious artifact.
I was a bit timid, so I didn't speed up the video.
Making a different noise.
What?
No, this bit.
Oh, yeah.
Uh, about there.
Yeah.
Now brimming with confidence, I could time lapse away.
Now doing another cut off, something which I never found easy.
As you can see, I've heated the wrong bit of the piece.
Oh, dear.
That was rubbish.
Okay, second heat.
Give it a few hard whacks.
Uh, yeah, I'm not very happy with that.
I've managed to bend it and I didn't get very far.
And it's not even a very straight slot.
Hey-ho!
Nice.
Looking better now.
Is that a good way of doing it?
Yep, go for it.
Hey, victory.
This is a pair of tin snips.
Now then, this putting a round bit on the end business,
has turned out to be a huge complication.
Because if it just tapers and comes to the usual sort of end,
and you make it a little bit too long, that's easy.
You just cut it shorter.
Or if it's a little bit too short, that's easy.
You just hammer it a bit more and draw it out longer.
But if you put a big blob on the end and you've made it too long,
how are you going to get it shorter again?
You can't.
So I've made things requiring of more skill.
You see, I didn't give it any thought.
I suppose if the absolute worst comes to the worst,
we could just cut the round bits off or just hammer them flat.
Oh wow, I got there quick.
Quick straighten.
Yeah, it doesn't want to be much longer, does it?
It doesn't, does it?
Yeah.
And your philosophy was that that distance...
Is this cold enough too?
Yeah.
That distance there should be similar to that distance there.
Yep, grinding.
Making the round bits rounder.
Just turn it round.
You'll see that the hole is not actually bang in the centre,
but I'm told this will give the sword character.
And now the twisting, another crucial stage.
Completely unnecessary dec...
Well, it gives a little bit of grip perhaps to the crossguard,
but it's mostly decoration.
And we've just established that we don't twist it three times round for three lines.
It's three quarters of a turn.
Okay, here we go.
Yep.
Because I had to get past the spheres at the end of the quillons,
I couldn't have the tool waiting ready at the correct setting.
So valuable seconds ticked away as I fumbled the thing into position.
Is it meant to grip completely or is that...
Yeah, that'd be fine.
That's close enough.
Okay, so...
You sure that's enough?
Yep, go.
One...
No, it's not gripping.
Pass.
And a quarter.
Is that it?
I can't see.
You need a little bit more to get it to line up.
Okay.
All right.
It's not quite straight, but...
Is it not?
It's not quite straight that way.
It needs to...
Oh, what, it's been bent?
Yeah.
Oh yeah, that's fine, that happens.
Okay.
Twists.
Take two.
The other half.
So I know I want to go...
Hang on, I went...
So I want to go anti-clockwise.
All right.
Okay, so he's dipping up to the bit that he wants twisting.
So he's cooling everything that we want to stay still.
Great time for it to slip.
Okay, that's not happening.
Grip, you swine.
Okay, so this time anti-clockwise.
One and a quarter.
Oh, it's tighter than the other one.
Okay, it's a little bit characterful.
There was only this much heat left because we took too long.
It's fumbled a little bit.
Final straighten with a mallet on wood,
so as not to spoil the ridges of the twists.
Dunk.
And there we are.
you
