Forest Bubble

Small gardens and aquaspace
198 followers
Hi everyone, I'm Russell Leydig and you are watching the Dangerous Fishbowl channel.
This is Forest Bubble, my latest Ecoquarium composition.
In this video, I'll explain its engineering evolution in detail.
If you want to learn about the plants and animals inside it,
check out the one entitled Forest Bubble Flora and Fauna,
or for a long, uncut series of 5-minute clips, see Forest Bubble Long View.
Let's get started.
First and foremost, I want to thank all of you
for helping to propel the Ecoquarium concept into the public consciousness
through your analysis and discussion surrounding the Jungle Bubble video,
which was my first serious attempt at creating a fishbowl which manages itself.
I subsequently tried to define the concept more precisely in
Introduction to the Ecoquarium, which is also available on this channel.
There were a number of flaws in the Jungle Bubble design,
as I discussed at length in Rethinking Jungle Bubble.
Without repeating them here,
suffice to say that I've gone to great lengths to improve upon the original concept.
For starters, I got rid of the need for CO2, or any artificial fertilizer for that matter.
And as you can see, the fish are tiny ember tetras quite at home in this giant bowl
with a diameter of about 45 centimeters and a capacity of about 45 liters.
By the way, I'll provide information in the description
on where to get all the materials required to build your own.
The bowl is made of acrylic, which is much stronger than glass and therefore much safer.
It's only a few millimeters thick,
but I banged into it once by mistake and it survived unscathed.
As you can see, there's a tiny seam at the equator due to the manufacturing process,
but otherwise it's very smooth and transmits more light than a glass fishbowl would.
The only downside is that it scratches very easily,
so you need to be paranoid about getting grains of sand
in the sponges and towels that you use for cleaning.
I keep a dedicated soft cloth just for this purpose.
I also use a felt furniture slider called a super slider
to clean tough green spot algae from the inside surface.
Whatever you use to scrub the bowl, do so in an invisible area first.
And by all means, exercise caution when using metal plant trimming tools,
which can easily nick the surface.
If you do damage the exterior,
you might want to check out the video on acrylic repair linked in the description.
The top, as you can see, is also acrylic.
It's 3 eighth inches thick and offset from the lip of the bowl by soft acrylic bumpers.
This facilitates gas exchange as well as clearance for the cord leading to the powerhead.
The powerhead itself is an inexpensive 90 gallon per hour unit.
You can't see it too well here,
but I super glued an extra suction cup to the cord
so as to prevent it from hanging into the water column.
It does require unclogging every week or so.
In order to do that, you will need to carefully slide it up to the lip of the bowl,
moving along the inside wall.
Do not pull on the suction cups.
Otherwise, your arm might suddenly jolt across the bowl, destroying everything in sight.
The cord is held in place by a spine made of foam cable stays called D wings.
I suppose you could put the last one at the equator
and just drop the cord vertically from there.
In this case, I've continued the spine all the way to the base.
The white plastic pipe is a four inch female adapter,
which is wide enough to be stable
and also has a bevel on its inside circumference
so as to alleviate pressure points on the bowl.
After all, it needs to support more than 50 kilograms with a very small contact area.
By the way, I recently learned that there's something called a repair coupling.
It has better aesthetics and might fit the purpose as well.
The adapter is cocked to another acrylic disc.
I was very careful to keep the thickness of the cock uniform
so as to avoid tilting the bowl.
After it dried, I applied an additional amount around the outside
in order to exclude water from the interior of the adapter.
And finally, this disc is underlaid by a cork mat of exactly the same radius.
The reason is, again, to exclude water.
We don't want it leaking between the layers
or between the rubber backing of the cork mat
and the surface of the table underneath.
Something you cannot see is that the driftwood is cocked to the base of the bowl.
This is mandatory unless you want to spend months or even years attempting to waterlog it.
Oh, and don't forget to clean it and dry it first.
You also need to use a lot of caulk in order to ensure structural integrity.
And definitely wear latex gloves and a respirator
because it's messy and somewhat of a toxic task.
If possible, lean the driftwood against the side of the bowl for extra support.
And bear in mind, it will probably get banged during cleaning from time to time.
Take care not to splatter the caulk on the visible part of the bowl,
which can be a pain to remove.
I let the caulk dry for at least 48 hours before proceeding
because it's never going to get another chance to do so.
You might then test the structural integrity of the driftwood
and reinforce with additional caulk if necessary.
Super glue might work as well, but I've never tried it.
The substrate, as usual, is pool sand.
Don't forget that it's an inhalation hazard when dry,
so wear a respirator and pour it out underwater.
If you plan on planting rooted plants or growing them from seeds,
you should do that while there's a shallow puddle of water covering the sand.
You could put some natural fertilizer near the roots as well,
although I don't recommend installing an entire layer of soil
as it's easily kicked into the water column.
Before filling the rest of the bowl with water,
I attached various mosses and anubias to the driftwood with super glue.
I learned this technique from Rachel O'Leary's channel.
Once again, you want to be wearing latex gloves and a respirator
as the fumes have only one way to escape,
which is directly into your face as you rearrange the plants.
Take care, too, not to splatter the super glue
all over the driftwood or worse, on the bowl.
It's still not time to fill the bowl.
Get a spray bottle and spray mist all over the plants that you just attached
or even one by one after attaching each of them.
This mist will help the super glue solidify because unlike normal glue,
it actually requires water to do so.
This will also prevent the plants from dehydrating during the aquascaping process.
If you like, use plant tongs to position your plants,
but remember that they can severely scratch your acrylic.
Finally, make sure that your bonds are strong enough
to withstand buffeting from water currents
because once the fish are in place, super glue cannot be used.
Now, finally, fill the bowl, leaving a few centimeters of air at the top
because we want to allow for further maintenance without causing an overflow.
It's also a good idea to refrain from maximum filling in any event
because the surface area to volume ratio of a spherical bowl is quite low
and we want to provide for sufficient gas exchange.
The first time you fill the bowl,
you may find bits of sand and super glue at the surface.
Use a plastic cup such as a yogurt cup to skim off this material.
The surface must be clear of debris in order to support your fish.
Having filled the bowl, I then installed the powerhead.
Well, actually not just yet.
I first super glued that extra suction cup
to the side of the cord facing the inner wall of the bowl.
This allowed me to affix the cord to the wall
so as to prevent it from dangling into the water column and creating a hazard.
I then placed the powerhead itself at the equator
such that the water jet runs exactly parallel to the floor.
This is critically important
because otherwise you'll end up with poor water circulation
and or excessive debris in the water.
If the flow is still too strong,
you can place it behind the driftwood like I have.
Personally, I like to fold the cord behind the powerhead
so that the jet is at the top instead of the bottom.
However, this makes the suction cups less effective
so I don't recommend doing so.
Finally, note that the cord needs to be sort of massaged
into the shape of the external spine.
In particular, I had to create a fold
at the point where it intersects the lip of the bowl
so that it would not push open the lid.
When you first start your bowl,
it's a good idea to cycle it for a week or more prior to adding fish.
And when you do add fish, add only a few at a time
because again, you're fighting a very low surface area.
So I recommend suitable nano fish
such as the tiny ember tetras in Forest Bubble.
During the cycling period,
you're going to need a source of ammonia
and trace minerals to nourish the plants.
Some of this will come from the soil fertilizer.
Optionally, you can add one milliliter of urine
per one liter of water.
Yeah, seriously, you cannot get cheaper than that.
Too much and your plants will die.
Too little and they won't grow.
But most definitely, your ammonia needs to be indetectable
before you add fish.
And if it's not obvious,
urine and fish don't belong in the same aquarium.
There's another hazard to be aware of,
which is especially important in a bowl.
It's what I call cascading death syndrome.
It works like this.
One fish dies for whatever reason.
Then its decay causes an ammonia spike.
The ammonia causes another fish to die and so on.
The fish die at an accelerating rate.
This is why it's so important to ensure
that you have enough plants to mitigate the ammonia supply
as rapidly as possible
and few enough fish to prevent this runaway process
from occurring in the first place.
And again, make sure to leave enough of an air gap
at the top of the bowl
so that your surface area is not too small.
I also provide 12 hours of light,
just like in the wild,
in order to sustain the plant's oxygen production
and appetite for waste products.
Above all, if you see your fish gathered at the surface,
you have a serious water quality problem,
which requires an immediate water change.
In that case, more than likely,
a fish has died and the ammonia level has risen drastically.
This occurs more often in the morning
because the plants are not as biologically active in the dark.
Speaking of light,
the entire setup is illuminated
by an IKEA Aerod floor lamp
with a 1300 lumen, 5000 kelvin,
that means daylight,
PAR38 LED bulb.
Now, trust me on this.
You don't want to put the light source
too close to the acrylic,
as even LED lamps with that kind of power
can get quite hot.
It's not just a fish hazard,
it's a fire hazard.
So keep at least 10 centimeters of separation
and make sure that the lamp
isn't going to slide out of position
and onto the bowl.
Given the geometry of this sort of aquarium,
it's important to alter the lighting angle
just as the sun moves across the sky.
Otherwise, you won't get optimal plant growth
and some plants might not grow at all.
I usually do one angle in the morning
and another in the evening.
I suppose it would also be possible
to alternate once a day.
It makes for impressive scenery variations as well.
As far as maintenance is concerned,
all I really do is trim the plants
and especially the ones
hogging all the light at the surface.
For that matter,
I choose plants such as Cryptocoryne ballense,
which is that tall spiral plant you see here.
The reason is that I want plants
that sort of grow all over the water column
as opposed to all over the surface.
Vallisneria, for example,
would not make a good bowl plant.
When I trim the plants,
I also unclog the filter.
Don't forget to unplug it first, of course.
I also use that furniture slider I mentioned
to remove pesky green spot algae
from the inside of the bowl.
The water always smells clean, never foul,
but I change it anyway
because over time it evolves a decoloration
due to the tannins which leach from the driftwood.
The fish like it, but I don't.
By the way, in order to avoid fish stress,
make sure not to change more than 75% of the water
and ideally not more than 50%.
In bowls like this and Ecoquaria generally,
it can take as much as a few days
for the debris to settle out of the water column
after a water change.
So don't be discouraged
if your water actually looks worse after the fact.
Just don't forget the dechlorinator.
So that's the engineering story.
But why have I bothered to do this at all?
The reason is that,
thanks in part to viewers like you,
I've come to understand
that two major disruptive trends
are evolving around the freshwater environment.
The first of these
is the obvious environmental destruction
and in particular,
the spoiling of natural freshwater supplies
which is occurring with accelerating frequency.
It's ironic that while the aquarium industry
has suffered declining popularity
over the past few decades,
its relevance as a connection to nature
and a safe harbor for endangered species
has grown substantially.
So I think it's not merely desirable,
but in fact necessary
that we as a society
evolve more efficient ways
of bringing the wild aquascape into our homes.
The second disruption
is a slow but steady shift
towards smaller aquaria.
This is evinced by the rise
in the popularity of nanotanks
as well as small ecoquaria
such as forest bubble.
I think it reflects a growing need
to minimize the economic
and environmental toll of fish keeping itself,
which is a good thing.
But it also promises to facilitate
a more ubiquitous domestication
of the freshwater environment.
This will become absolutely necessary
if we are to maintain
even a vague approximation
of our natural heritage
in a future increasingly defined
by virtual worlds
and engineered infrastructure.
So think of forest bubble
as a seed from which to grow
your own ideas
about how to bring nature into your home
in a manner which is economically
and environmentally sustainable.
And yet the aesthetics
and moreover the opportunity
for introspection and learning
are unmatched by any technology
which we might ever hope to create.
I hope that forest bubble
has inspired you to dream
of a river or a lake or an ocean
right there in your own room
in the midst of this grand
artificial construct
which we call civilization.
So that we might never forget
that we too are part of nature.
Thank you for listening.
