Everyone Need To Have Atleast One Of These

The Soul of Wood
152 followers
Hi, hello, welcome back. Now, I thought it would be a cool idea to show you this
nice looking set that I've done today for a client.
This is a big birch bowl, 11 and a half diameter by five deep.
And you might remember this bowl being roughed out roughly a year ago.
So like I said, it's birch and it says here Breza, that's in Croatian for the birch.
And you can see a lovely figure on the inside, two lovely beads on the outside.
And you're going to see one of these plates, walnut plates, being turned in this video.
So these are, you can see, closely matched on the bottom as well.
Really nice walnut. And this is also walnut ladle.
Slightly different species of walnut, not sure which one.
This is two inches diameter and a really nice size ladle.
This is pretty much the most common type of work that I usually do.
So it's a variety of the stuff. So it could be for the one client, let's say a bowl,
maybe smaller, two bowls, and then maybe a box or a spatula or something like that.
Combination of the variety of the stuff, let's say.
Yeah, so like I said, you're going to see one of these walnut plates being turned.
So we need to go back in time and I'll show you how I've done that.
So this is first plate done and you can see the bottom and the details.
Really simple, didn't go any crazy details or anything like that.
And the show face, the top, also really quite simple.
The detail here to distinguish the rim from the inside is just a little half round here.
And this is slightly crowned, this is slightly dished.
The edge here is nicely rounded over. So everything is nice and soft when you hold it.
The wood will speak for itself once we get the oil on.
Should be really, really nice.
Now, usually I would always rough turn my plates.
Now, this one isn't from Quattro Sun, this is from Flat Sun stock.
So what I would always do is rough this out maybe two times before I get to the final dimension.
Now, this is only roughed out once and it's relatively stable timber, so it should be okay.
So I have left this little island, little tenon here on the inside,
so I can grip and turn the outside first.
First, I would start with this area here, refiner.
Speed will be roughly 1450.
Should just lightly go over.
And I want the plate sitting only on this small outside rim.
So I need to take down the middle here.
So I'm resting right up against this edge here, so that's good.
For now, I'll leave it as it is and I'll shape this area here.
Just a simple curve, that should be okay.
And now I'll use a refiner again to refine this surface,
but I will support with my fingers the back of the plate, so I don't get any chatter.
And this foot here, I'll clean up with the spindle gouge.
And that's really nice and polished, so that doesn't really need sanding.
Okay, that's pretty good.
Since these are only two plates, I'll do most of the details,
copying of the details by eye, only the rim width I'll mark.
Okay, so that should be okay.
So what I need to do now is true up the recess.
Now I did have to move the camera slightly to the right, so I can see better what I'm doing.
Small skill, get this detail nice and clean.
And also undercut the recess.
Okay, so you want to see probably how this looks.
So that's pretty clean.
And just want to double check that I'm resting only on the outside portion.
And it's actually here and to the outside rim, so I could just a little bit bring this down.
So that's outside finished.
Really nice walnut.
So now we can grip by this little recess.
Expand the jaws.
You don't need a ton of pressure.
Now to get it close to the other plate,
I have in terms of diameter to take down roughly around here.
But also in terms of height to get it down maybe three mil.
So that's what I'm going to do first.
So again, refiner and I'll go lightly.
So that's diameter taken care of.
And this is the height, so I can remove this.
Now with the ball gouge, I'll just crown this ever so slightly.
Like this.
So this measurement is at the rim detail.
So somewhere around here.
I'll rough it out with the refiner.
So that's the bottom of the hole.
Now what I can do is, I know that on the first plate,
roughly the thickness in the very middle is around seven mil.
And I will have to take the plate out and I'll just measure the thickness.
So that's around 11 mil.
So I can bring that down a little bit more.
And I'll also measure where the recess is, as that's the thinnest point.
And that's also 11-12 mil.
So I have enough timber for a nice flowing curve.
Going right into a corner.
And one more tiny scrape with the refiner.
So the plates are done.
And what I've done off the camera is sign them.
And if you're wondering what this is, this is Orah.
That means walnut in Croatian.
So since this is going to Croatian customer, I like to put Croatian name for the timber.
So as you can see, let me just show you the bottom.
These are really closely matched.
And in terms of profile as well.
And on the top, to show you the details here on the rim as well.
These are really closely again matched.
Mostly by eye apart from, as you saw, describing the line for the width of the rim here.
So really nice, simple, quick job.
And hopefully you like this kind of video.
And thank you for watching and see you in the next one.
