DIY roll crimper for the 410 shotshell

The Skill Tutor
20 followers
15 Video Views·Oct 30, 2022
Hello everyone and welcome. I hope everybody had a merry Christmas and that we all have a
better new year. I've had several requests to do a roll crimper for the 410 shotgun shell,
so that's what I'm going to do today. Now there are a lot of videos out there on making a roll
crimper not just for the 410 shotgun shell, but for the 12 gauge, 20, so forth and so on,
and they all involve, you know, lays, machining this, miking that, specialty tool for this.
I'm not going to do any of that. The roll crimper that I'm going to make today is going to be one
that anybody could make with just some simple hand tools. Let's go in the shop and get started.
For the body of my roll crimper, I'm going to use a one and a quarter inch dowel,
and this was actually left over from when we put in one of those clothing systems in my fiance's
closet, and this was used, you know, to hang clothes on, and I'm going to cut about an inch
and a half off of this. I got the piece cut for my body and I got my center lines drawn with this
being an inch and a quarter piece. They should be five-eighths of an inch to the center. With my
center lines done, I'm now going to take a 15-30 seconds drill bit and I'm going to drill five-eighths
of an inch deep. A 15-30 seconds drill bit was the closest I could find to the dimension of a 410
shot shell. Now that I've got that done, I need to work on what I'm going to use as my mandrel.
For my mandrel, I'm going to use this large nail, and this is bigger than a 16 penny nail, so I guess
this would be like a 20 penny nail, but just kind of looking at it, it looks like it's going to fit
right inside the roll crimp on a shotgun shell that is factory roll crimped. So here's the spike
after I cut it down and polished it, and it looks like it's going to fit perfectly inside of that
roll crimp on a factory roll crimp shotgun shell, and I cut it off at two and a half inches long.
All right, so I got my hole drilled for my mandrel. It's going to fit in kind of like that. It's kind
of a snug fit, which is what I want. I see it coming through right there. So here's a look inside
the basic workings of my roll crimper. I've got my mandrel sticking through into the cavity itself
about a quarter of an inch, and before I go any further, I'm going to go ahead and start shaping this
and polishing it up a little bit, and then get into the finer details of fixing this mandrel
to the body itself. To shape this, I'm just going to use some hand tools. I've got my basic shape
done. Now I'm going to chuck it up in my drill and kind of refine the shape a little bit,
and to do that, I've got just a rod that has some threads and a nut on the end of it,
and I'm going to take and slide it through on the large end so the nut will kind of fit in there,
and then chuck the whole thing up in my drill. So here's my final shape. I'm not going to do
any finish sanding or staining right now. I'm going to try to figure out how I'm going to mount my
mandrel, and I believe that because this hole is five-eighths of an inch deep, if I come a half
inch here and drill a hole and mark my mandrel, I can pin it in place using that method. I just
got to figure out how far I want my mandrel to stick out past that pin. I think what I'm going
to do is go like an eighth of an inch past my drill bit, or try to, and go that route and see
how that does. All right, so I took a piece of coat hanger and stuck it through the holes kind
of to pin it in place, just kind of temporary, and like I said, I couldn't find anything more
high-tech than that, but I think I'm going to go ahead and cut this off and maybe give it a test to
see how it's going to do. I got a couple of wonky 410 shotgun shells. I'm going to take and cut the
crimp off these, and I'm going to use these kind of as my test medium. Well, it kind of works. I'm kind
of getting a crimp, so what I'm going to do is I'm going to move my hole back about an eighth of an inch
to see if maybe it needs to be closer to the bottom. After kind of getting a roll crimp, I took
and put some epoxy down on the bottom of this to try to smooth out some of the edges to see if that
would help, and I've got a couple more shotgun shells to try. Well, that's a little bit better.
It actually looked like it crimped it rather than just melted the plastic on it, so I can deal with
that. I've got another shotgun shell, and this one appears to be a little bit thicker, so I'm going
to try it and see. There'll be a wad in there. Yeah, like I said, it is working a little bit better now.
I'll see how they fit into my gun.
It's a little tight. They do work, and I'm going to consider that a success.
Now that I've got this working, I'm going to cut these little nubs off, sand it, and stain it.
So there is making a roll crimper for the 410 shotgun shell, and just have to say that several
shotgun shells were injured in the making of this video. Now, I have talked to several people who I
consider to be experts in reloading shotgun shells, and they all tell me the same thing,
that a roll crimp was actually designed for the paper 12-gauge shells. I don't even know if they
made a 410 paper shell, but anyway, that's why most of the shotgun shells you see today are
star crimp rather than roll crimp, and there are some manufacturers who actually roll crimp 410
shotgun shells, and with this roll crimper that I made, I found that those will actually
roll crimp better than just a standard shotgun shell, I guess because they're thinner. Now,
this roll crimper doesn't produce a factory looking roll crimp per se, but it does work
as a roll crimper because the first couple attempts that I did, it was literally melting
the plastic instead of roll crimping it. So I took and kind of slowed things down a little bit,
added some epoxy to kind of smooth out the edges inside that cavity, and it does work a little bit
better. So making this roll crimper kind of gives you the premise of how the roll crimper actually
works, and if you have a lathe and metal working stuff, that's all great and wonderful, and a lot
of people don't, and this is just a cheap way of making a roll crimper if you just
absolutely have to have one. So thank y'all for watching. We'll see y'all next time.
