Cheap 2x4 Material For Upcoming Holiday Gifts

The Soul of Wood
152 followers
So this is the board I'll be using in this video and it's actually slightly less than a 2x4. It's
an inch and a half thick by a little over three and a half inches wide and you can see here I
already made a couple of bowls and this one has a pit going through so not ideal but
should be okay. And on this one you can see I already marked the waist here where the knot is
and on this end as well. And now what I'm going to do is make another bowl to show you how I
do this on a pine like this and also we'll make a cross grain box. So I'll just mark three squares
and I'll cut them on the bandsaw and then I'll show you back here on the lathe. So you can see
and what I've done is mark the centers via diagonals and drill a hole here so that will
go on a screw chuck like this and I also cut away two spindle blanks for later. And this will be a
bowl so we'll make it nice and quick. Speed will be around 1600 rpm. A spindle gouge half inch
So this is the smallest chuck I have.
surface on pine. Here it's quite rough and here you can see it's not that bad. Still need a little
scraping here and we need to clean this up. So on this side with the spindle gouge
make nice detail. Clean this up. So that's done.
So now just finesse the outside here. So this MDF here is in my way
and the plywood. So just remove that real quick. Okay so that's now outside done.
You can see that's a really good surface and we'll quickly sand that.
I'll put the finish on the lathe. This is Odi's oil. Have some left over so
good time to use it. I'll bring the speed up to buff it off.
So that's done. So first bowl is done. Take it off and I'll finish the inside.
Bowl gouge. Bring the speed up. It's a small piece of wood 1800 rpm.
With the finishing. This is a rag with less oil in it to buff it any extra off.
And that's the first one done. The first project.
And you can see there is no sign of gripping the foot. You can see the inside.
So really nice bowl and you can join the rest of it. Now I'm back with the screw chuck
and this will be the base of the box. So just thread that on. This is the outside and the bottom.
We'll quickly round this over.
The rest is slightly too small, too low.
Panel gouge nice and sharp. Let's do one more cut here.
Now I am going slightly against the grain so I might do this cut on the other side.
From the other side but as you can see that's a really good surface. This mark
is the second step in the step jaws. So that's my tenon.
And I don't like this keeping flat so let's flare it out.
Like so. Yeah that's looking a little bit better. This is slightly too tall.
And with the skew to make a little decoration here. Take away this sharp edge. Now this
area here I'll just sand the top portion. I might change this slightly.
The oil and clean the rag. Like I said this area we still need to finish the shape a little bit.
Okay so that's the bottom done. So I'll quickly do the the lid as well. Now the inside of the
lid is now here where the screw hole is and all I want to do now is just put a little
tenon here so I can remove the screw chuck. Again spindle gouge.
Okay so that's good enough. So these are step jaws you can see.
We have three levels that we can grip and we are going to grip with the middle one.
So I just want to slightly change this curve a little bit more. This is 19 mm square end scraper.
Quickly hollow this out. Just want to double check the depth. I can still go slightly deeper.
So I put the fresh burr on and I need to raise the rest.
So only this top left corner is touching the timber.
So the bottom is nice and clean. So I'll use a 10 mm spindle gouge to cut the side nice and clean.
Again finishing. Just make sure you cover everything and then buff away the excess.
Okay that's looking really lovely. This tenon will go into this chuck
and we'll do the inside first. So true it up first.
So I can mark the inside of the base.
So that lip will grab this almost.
And this needs to be a loose fit because this will move. Okay so that's good.
Shoulder here real quick. Nicely done. So now we can do a little bit of inside.
real detail. Maybe I'll put the lip here.
So there is a lot of corner here left. So remove that.
Back with the polishing.
That's looking quite good. And I will be able to hopefully expand these jaws
into one of these grooves. I think the bigger one is probably okay. And just light pressure out.
how this looks with the base. And I hope you can see. Slight too big of a diameter here on the lid
but overall not too bad. I'm quite pleased with this. So just reduce slightly on the diameter.
Maybe a millimeter and a half. Something like that. And the rest is quite good.
And if I continue on from this side I'll probably break off quite a big chunk. So
go from this end. I'm gonna make some nice little reverse curve on this side.
as a shear scraper. Just to finesse this ever so slightly.
A rag around your fingers because if it does cut in the chuck that will be a really bad day. So
I'm just holding it. Or you can use a paper towel. Doesn't really matter.
So that's the lid done. Now just wipe away the dust on the inside. So this is our lid.
Our base. And they fit nicely. So we have a lovely box. We got two balls from before.
We have from this video one lovely ball. You can see it looks really lovely. And this little guy.
Lovely little box. So hopefully you like this kind of idea what to do with 2x4. Nothing crazy.
Nothing super extraordinary. But just a simple gift idea. So thank you for watching and see you next time.
