Building Our Dream Entertainment Center | Start to Finish DIY

Modern house architecture
12 followers
6 Video Views·Jan 7, 2025
Today we're going to show you how we transformed our family room from this to this.
Now let us show you how we did it.
The first step in the process was planning out the design.
We opted for a darker color scheme accented with floating wood shelves and a 21-foot custom
countertop.
We also planned to incorporate LED lighting throughout to really make it pop.
So without further ado, let's build this thing.
Now I am a sucker for building custom cabinetry, but Bianca helps to remind me that we can't
spend a year building this thing, so we opted for the IKEA Besta cabinet.
We bought five of them and we'll make it look like one seamless cabinet.
At least that's the plan.
Now before we mount the cabinets, we had to run some electrical.
I started by installing a surge-protected recessed outlet for the future TV, which also
conveniently has a place to run the HDMI cables.
I then cut out some more drywall to run the speaker wire for the future 5.1 surround sound,
and there's no need to worry.
All this drywall will be covered up in the end, along with all of that wallpaper too.
It's now finally time to start mounting these cabinets.
We've been waiting for this day for a very long time, as has Olive.
So we're going to go ahead and start with the first one, and as you can see, we have
a laser set up to make sure we can get them perfectly straight all the way across.
So let's get to it.
With the mounting hardware in place, we can go ahead and put the cabinet on the wall.
Now we were a bit concerned with this IKEA mounting bracket, as we had never used it
before and were unsure on its actual weight capacity.
But after putting the cabinet in place, we were happily surprised as it felt really sturdy.
So with this one done, let's do the other four.
Here, Bianca and I are feeding an HDMI cord from the upper box I installed earlier down
to the middle cabinet, where I'll have my receiver.
We have to make some adjustments still, but looking pretty good.
Now in order to make this all look like one seamless cabinet, I added some shims behind
the cabinet boxes and then tightened them down onto their mounting hardware.
And this got the boxes pretty well aligned, but not perfect.
I then finished adding all of the doors on the front of the cabinets, and everything
was looking pretty askew, as you can see.
Lots of doors are at different heights and at different depths, which you can't really
see from this view.
So I then started in the middle and adjusted the hinges on that middle cabinet, got them
perfect and all of the seams perfect, and then I worked my way to the outside, making
sure that all the cabinets had the same gap between them, so you didn't know which side
the hinges were on.
And then everything looked nice and perfect.
So next up is covering up the wallpaper and exposed drywall underneath all of these cabinets.
Now we could have just replaced this drywall as we did on these two walls.
However, we opted to leave it in place and we're just going to cover it up with some
eighth inch Yucca board, which I cut into 10 and a half inch strips.
We just need to cut around a few outlets, but then we can glue and nail it in place
and then we'll paint it the same wall color as these two walls.
Let's get to it.
I'm trying to put one low because it'll be covered by the baseboard and then one high
because you won't really see it.
Cool.
So Grant graciously hung up all five IKEA cabinets, but you can see here, it unfortunately
does not go wall to wall.
This gap over here, we did buy an extra door frame that we'll be able to custom fit here
and it'll be an easy install since we can attach it to this wall.
But over here where their doors are, it's going to be a little bit trickier because
not only do we have the door, but we'll also be installing a piece of trim, so it's going
to be quite a sharp angle, but we're going to figure it out.
First up is cutting up that extra door.
Wow.
IKEA's made a part of the whole board.
They didn't lie to me this whole time.
Alright, so we're now ready to mount this board.
We ended up attaching another board at a right angle with some pocket screws, and then we
have two screws here that we'll screw into the stud of this wall, so it'll go in like
this.
We'll just screw it in here, and then as you can see, there's some light here, so we want
to make sure to cover that up, so we'll use a scrap piece of our black cabinet door front
to go right behind this so you don't ever see it.
Alright, so now let's build that 21-foot custom countertop.
We bought 1x12s and 1x6s to build up to that 17-inch depth that we need, and then we're
going to have to glue multiple pieces together to get to that 21-foot width.
Now these glue-ups are not easy, so in order to assist me, I added biscuits to all the
edges as well as pocket screws, so that way I can make sure it's perfectly aligned.
Now these boards were not perfectly square or straight, so some of these glue-ups were
quite challenging.
As you can see here, this seam with these two boards was perfectly straight without
any gaps.
However, the butt joint was closed at one end but had an eighth-inch gap at the other,
so I had to get pretty creative with how I glued this up.
I ended up using a scrap board that I could clamp against, and as I tightened this clamp,
it would allow that corner to kind of swing out and make an even gap from top to bottom,
and then I could use my mallet to knock it into place and have the seam perfectly tight.
From there, I went piece by piece gluing everything up, and I used the actual cabinets and walls
to help me measure to make sure everything was nice and accurate.
The back side of the countertop is made up of the 1x6s and the seams right down the middle.
However, I didn't want a seam on the front where the 1x12s are, and I also wanted to
stagger the seams to make the countertop a little bit stronger.
So there's one piece right in the middle that's about 12 feet, and then two smaller
pieces off to the side.
That way you don't really see the seams when looking at the counter.
Now as with most old houses, the walls are never straight.
As you can see here, this wall bows in quite a lot, so one option is for me to scribe the
entire counter.
However, that would take quite a while, and I don't want to cut into all of this oak.
So I went with the easy route and just cut away a lot of the drywall.
That way I could just slide the counter into the drywall and it would be perfectly flush.
Alright, so this is the last piece that we need to glue up to finish the countertop,
and we have an angled cut over here.
I was able to mark it flush with this door, and we want to just mirror the exact angle.
I don't really care what the angle is, I just want to make sure it's parallel to this door
front.
So I just scribed a line with my pencil, now I can take it off, cut it with the track saw,
reinstall it to make sure it looks good, then mark our biscuits and pocket holes, and finish
this glue up.
Now before we can install this beast, I gave it a sanding as it'd be a lot easier to work
on here on the ground, and I worked my way up to 220 grit, mainly focusing on all of
the seams.
And then I noticed that this board was a little bit wider than the other, which is not my
fault, but it is what I get for buying hardwood at Home Depot.
Luckily I was able to fix it with my track saw with just a flush cut.
Alright, I think it's finally time to install this thing.
It's very precarious, it's exactly the width of the room, so it's hard to get in and out.
I've never lifted this, Grant's been picking this thing up and down, so I'm self-assaulting.
Ready?
One, two, three.
Okay.
Alright, here we go.
Alright, are you in?
Yeah.
Is it in?
Yeah.
Wow.
That looks pretty good.
So the countertop is nearly complete, but there's one more step, and that's going to
be adding a one and a half inch piece to the front to give it a little bit of a thicker
look, and hopefully everything goes nice and smooth.
Let's get to it.
Isn't this genius?
It's perfect.
It was then time to apply a finish.
We went with a water-based satin finish because we didn't want the wood to yellow too much,
which does happen with oil-based finishes.
I applied it to a test piece, got it from Bianca, and we also compared it to our floors
because we wanted them to match as closely as possible.
I then applied it with a foam brush, sanding in between coats, and in total I did three
coats to get a buttery smooth surface.
And while we let that finish dry, we have two new packages to unbox.
To go with the big TV, we got a very nice surround system.
We're really excited because not only do these sound good, but they look really cool too.
Holy cow, this thing's huge.
I don't know where this is going to go in the room yet.
How do I grab this?
Can you pull the box?
Oh.
It's going to match our black cabinet so well.
On to the second one, which I'm even more excited for.
A box within a box.
Wow, this countertop turned out great.
We love the color of the finish as well as the sheen.
It's a satin sheen.
It's not too glossy, but not too matte either.
And now we're really excited to get started on this media wall.
But first we had to clear the entire room because we have a delivery coming.
That's right, people.
We got a new couch.
And after giving it a quick test drive, we could finally start covering up all that remaining
wallpaper.
All right, the day has finally come.
We bought this a few weeks ago, but finally time to install it.
The reason we're installing it is because we want to make sure that we don't want to
expand the slat wall that's going here any further to the left or to the right, and to
make sure that we have it at the right height.
So let's go ahead and open it up.
So we got the mount on the wall and the mount on the back of the TV.
Now we just need to connect them.
So easy.
Like this TV is like thinner than your phone.
One, two, three, slide.
All right, now one, two, three, pick up.
Okay.
Can you hold it for a sec?
I need to move the towel.
Yeah.
One, two, three.
Higher.
Is mine in?
Yeah, it's in.
I love it.
Okay, I want to turn it on.
Wow.
Even the world looks good.
Wow.
Holy cow, it looks so good.
So we got the Yooka board up and this is the original width and the sketch up of the slat
wall we wanted.
But after mounting the TV and seeing it with the speakers, we think we want to go a little
wider.
So we cut some extra strips of Yooka.
This is four inches here, so we're going to add four inches on each side.
And luckily we did the math and figured it out and that seam here will be covered up
by slat.
Need a flag here, sir.
Last piece.
I'm excited.
Never see this wallpaper again.
This is crazy.
No more wallpaper.
Wow.
It's huge.
So we also marked out the studs with the blue tape on the counter and then we're using the
laser to do that straight line so Grant can just go bam, bam, bam, and hit a stud every
time.
Wow.
The room feels huge.
All right, so now we're going to be cutting the MDF into 10 inch strips that will make
up kind of the border of the shelves and the perimeter of the whole thing.
It's like clockwork.
Every time I hit record, someone starts mowing their lawn, so apologies for the background
noise.
Okay, cool.
Now let's go ahead and cut these strips.
Okay, do we think it's going to fit?
Yes.
Manifested, right?
I mean, I hope it's honestly a little smooth.
Wait, I have an idea.
Let's get the laser and put it directly on the line.
So now we are finally ready to apply paint and primer to the Yucca board behind the TV
where we're doing our black on black slat wall.
We first made sure to sand all of the nail holes and then we didn't want to get paint
on our oak counters, so Bianca came up with a great idea to add really thin magazine paper
and slide it underneath the Yucca board because it's really hard to get a tape line perfectly
along there.
So this will work great.
Now let's go ahead and start priming.
So now all the boards are cut and painted, so now all we have left to do is install them.
The very first board is going to be pretty tricky.
We're going to do the very first one in the middle here and then work our way to the right
and to the left.
We want to make sure this first one is perfectly level because we're going to reference that
for all of the other boards.
Let's see how it goes.
So it's 1130 right now.
We just really wanted to finish this project before we went to bed and get the TV up.
It's my birthday party tomorrow, so I told Grant we have to finish it.
Yeah, we have people coming over.
We want to show it off.
It's still not done, obviously, but this is like a big cosmetic lift.
One issue is that we have the speaker wire coming out of the wall right here.
I have no idea if it's going to land on a slide or not, so we're going to find out when
we get there.
We have the seam to cover up, making sure that happens, and hopefully there's enough
room to get that last slide and we don't have to rip it on the table saw to get it to fit.
Grant said this would go by really quickly.
It will.
Do you even need me right now?
For moral support.
Can you get me a chair?
You can bring a chair.
That looks terrible on camera.
That's what you normally do.
You just sit around and watch.
It's past my bedtime.
I'm joking.
You helped a lot.
Great job.
Here, I'll wipe the board.
Then at least I'll be moving in my time lapse.
And these are longer, so we nailed the top and bottom with a spacer, and then I like
to put one here in the middle.
You can see here, it's just ever so slightly bowed, so this just makes sure it's still
nice and straight.
And then he'll check with a laser.
Well, then the laser double-checks everything, because you don't want to have one slightly
off and then you keep going over and over and the air keeps compounding, and then when
you get to the end, you're at a massive angle.
I'm just standing here.
I'm Vanna White.
Maybe you should film when I'm a little dilulu.
There's just so many thoughts in there.
I just like, so much is bouncing around in here.
This is really long.
Bam!
Did you watch Emma Lugosi growing up?
Wow, it looks like cooler on camera than it does in real life.
What?
Great job!
I eventually made my way to the speaker wire, and it landed directly in the middle of a
slat, but it ended up working out as I drilled a hole in the side of the slat, and the speaker
wire could just pop out the side.
And luckily, both vertical seams were covered by a slat, so we didn't have to worry about
patching it up or anything, but we did end up having to rip down the two outer slats.
We then struggled once again to get the TV back into place, and then it was on to addressing
the two sides of the media center.
The next project is building three floating shelves that will flank either side of the
TV.
I already built all the shelves on the left side of the TV and love how they turned out
and worked out all the kinks in the building process, so now we're going to build all three
shelves to the right side.
Let's get to it.
Now, each shelf is made out of two boards, so that's 12 boards in total across all six
shelves.
And I strategically placed which grain pattern I liked in which location and made this little
diagram to keep track of which board went where.
All right, so let's go ahead and glue up our first shelf.
So we have a top and bottom piece made out of the half-inch oak plywood, and then the
front piece is a full solid oak one by two.
Now, the tricky thing during this glue up is that there's only a front, top, and bottom.
There's no sides and there's no back, so it's kind of hard to support everything.
So in order to fix that, I cut down these strips of plywood, which are the exact thickness
I'm going to have in the middle of the shelf.
I'm going to clamp these in place along the backside, flip it over, and then glue up the
front and nail it in place.
And the next step is glue.
I'm going to be using Titebond III because it has a little bit longer of a working time.
We're going to put two beads all across these two pieces of plywood and then put on the
top piece.
Now, to nail it, I'm going to be using a 23-gauge pin nailer, that way the nail holes are practically
invisible.
And I'm going to nail all the boards on just one piece of plywood, then come back and nail
the others.
I'm making sure the plywood is flush with the edge of the one by two oak board.
All right, that's one board down, two more to go.
And of course, the very last nail pops out the side of the shelf.
Luckily, I was able to snip it off and patch up the oak, but these are never fun to deal
with.
I want to keep these shelves as light as possible because they are floating and extra weight
could make them sag over time.
But I do need to strengthen up each of the insides of the shelves because they're completely
hollow and they definitely can move without any support.
So I cut some of these pieces of plywood to the correct width of the inside of each of
the shelves.
I'll add some glue and then slide these into place like so, clamp them up and that'll add
a lot of rigidity to the shelf.
Now, I left all of these boards long because I wanted to cut everything down to size after
the glue up because during the glue up, things tend to move around a little bit.
This allows you to get perfectly clean lines and have all of the boards cut to the exact
same width.
I then had to figure out how I was going to mount these floating shelves and there's a
variety of ways to do this, but I opted to basically form a perimeter around the back
and sides of the shelf that I could then slide the shelf onto and this worked out really
well.
With the shelves complete, the next big project was installing all of the LED lighting.
I wanted it in three different locations and I started with what I thought was the easiest,
which is underneath all of those IKEA Besta cabinets going all the way across from one
end to the other to give a really cool glow at night.
I made sure to buy LEDs that had an adhesive backing that way I could just stick it into
place and I also used my laser to make sure I kept it in a straight line.
Once those were installed, I could run a wire from the left end of the media center all
the way to the right where the power supply will be.
The second location of the LEDs is behind the TV to give it an ambient glow.
I made a border out of scrap material that way I could stick the LEDs on the side of
it to cast the light outward.
Once that was complete, the third and final location of the LEDs is going to be built
into each and every floating shelf, which was not going to be easy.
All right, so it is finally time to cut the router slots for the light strips and all
these shelves and I am so nervous because I spend so much time working on these shelves
and I do not want them to be ruined.
So really hoping this goes well.
I'm going to start with the top shelf on the left side.
So the one that's least seen just in case anything goes wrong, but I already cut a spare
piece of MDF just to make sure I dialed in my settings correctly.
It's looking good so far, so hopefully it goes well.
Wish me luck.
I'm going to be using this edge guide to keep it straight and as you can see, I'm in my
rotary apparel.
This is the type of stuff you need to wear to do this sort of project.
God, I am really nervous.
Routers, man, they're like tough to use and intimidating, but they really make a project
look nice. That is clean.
All right. Five more shelves to do.
Let's do it.
Once all the routering was complete, I applied three coats of the same water-based
polyurethane that we used on the countertop earlier to all six shelves.
That way they'd match nicely.
And then we had to figure out what we're doing with the Yucca board behind the shelves.
So we searched high and low for a wallpaper option for these side panels and we found
one we really like that has texture and a nice sheen and we thought would be the color
we wanted. But upon taking a step back and looking at it, we weren't in love with it.
But I think we found an alternative solution that we like a lot better and will also be
easier to apply. Hello and happy Halloween.
I know we're dressed a little differently, but that's because even on the holidays,
we're still working. So between trick-or-treaters, we're currently marking out the
shelves because we're going to pull these off and then start applying that concrete.
Chef by day, builder by night.
Now this concrete that we've been using is actually a feather finish used for
underlayment, patching and skim coating, but it works great for accent walls as it
provides a really cool texture.
You've probably seen this used in a lot of our past projects if you've been following
along with the channel. But for this project, we wanted it to dry a little bit darker
than it usually does. And that's why we added that pigment earlier on.
So it is now time to take off all of the tape.
I'm going to start from the top and work my way down that way.
If anything does fall, it'll fall onto the sheet here and then we'll just be able to
wrap it up and throw it away.
The concrete patch has fully dried and it's the perfect color.
It's not too dark, but not too light either.
And in the meantime, I was able to install all the lighting in the shelves here on the
left of the TV. So now let's go ahead and do the right side.
So the way that this is going to work is that I have a power supply down here.
I'm going to run a wire from there up through the counter up to here to the first
shelf, and that will feed the power to the LED strip right here, going all the way
across. Then I'll have a wire going from here to the second shelf, feeding this LED
strip and so on and so on like a snake up the shelving.
And you might be wondering about what about all these wires that are going to be
showing? But we still have some trim to put on the front here that will cover all
those wires. So it'll look nice and seamless.
Let's get to it.
So that little component that we just wired in is a receiver, and that way we can
control the LEDs with a remote as well as dim them to the desired brightness.
I then cut all of the LED strips, aluminum rails and diffusers to size.
Now, I did a ton of research when deciding on which LEDs to use and all of the
components, so I'll make sure to link everything down in the description.
But I opted for COB LEDs, which stands for chip on board.
And this allows for a continuous stream of light.
And you don't actually see the individual diodes on the strip.
But even so, I still opted to use diffusers just for that clean look.
All right, it's time to give it a test.
Sweet. Now we just have to do that three more times.
Now, the top shelf didn't have a rotted slot to slide my LED rail into, but the
rails did come with these clips, so I installed four of them and then popped
the rail into place.
And luckily, all of this will be covered by trim, so you'll just see the ambient
light in the end. And speaking of that trim, this is the last major project of
this media center, which I am so happy we're almost done.
I just had to hog out some material to make room for the LED wires and I could
get to painting and then installing.
It is finally time to pull off the plastic on the TV.
Here we go.
From there, all we had left were the finishing touches.
I used some hot glue to hide all the wires from the LED cables and then we could
decorate the shelves. And with that, this project is complete.
So what do you guys think? I mean, I think this looks pretty freaking cool.
I had high expectations going into the project, but it even blew those away.
This was definitely a labor of love with lots of long nights and a lot of work,
mostly from Grant. But we are so happy with how it turned out and it really
elevates our family room.
And if you enjoyed this project, we'd really appreciate it if you could give
it a like, as it really helps out the channel.
Put a lot of blood, sweat and tears in this project and a lot of blood, sweat and
tears into this edit. It's probably one of my longest to date,
so we'd really appreciate that.
And also if you want to see us complete this family room, there's actually a few
more projects left as well as the rest of our house.
Hit that subscribe button as we have a ton more content coming your way.
And if you're curious,
all of the tools and products used throughout this entire video are linked down
in the description. Now that this is done,
this has quickly become our favorite space in the house.
We really love watching our TV shows and movies with all of Grant's TV and
spouses, so it was definitely worth it.
We especially love spending time in here at night with all the LEDs lighting up
the space. And I put them on four different zones so you can change which ones
are on, which ones are off and change all their dimness settings.
So you can dial it in perfectly. So it's not too bright or too dark.
If you have any questions,
please feel free to leave them in the comments below and we'd be happy to
answer them.
We did have a few doubts and sometimes we hesitated going with this all black
wall, but we're really happy with how it turned out.
And we feel like all the pieces on the shelves really pop now.
And one of the main reasons that this video took a while to come out is because
we wanted to fully decorate all of these shelves and we didn't want to just
throw a bunch of chachkis up there.
So a lot of these items are actually personal to us and sentimental.
So they mean a lot and it feels like we really made it our own.
And as always, thanks for watching and happy building. See you next time.
Bye bye. Ready? Yeah. I just feel, what are you doing with your hands?
They're like Ricky Bobby. Do you even know what I'm talking about?
Is that like Talladega nights or whatever? Talladega. Anyway, one more,
one more. The fingers are kind of grossing me out now. This is your thing.
I know, but it's like overkill being a dead horse,
but it's just going to be on so many takes. It's only going to be in the video.
We really want to keep that continuous look, but you'll see we have a gap here.
They can see how nice my nails are. That's what the people want to see.
It's a little small. I know. Really? I think it's fine.
Remember before you were like, it's going to be too big.
And now you're saying it's too small. I think it's fine.
I appreciate how fast it is. That's how fast I redid my head.
All right. We're going to set it up. We don't want to show you all of it.
Oh my God. I forgot we were mic'd.
Can you stop mine? All of these shots are like just booty shots of you.
You know, it's huge in here, dude.
My butt.
Very funny. The room.
We're done. Good job.
No, I hate that.
Here you can set them down. You turn off the camera, right?
No. Oh, I'm just going to do a time-lapse.
Thank God. Take his mic off me. Hello and happy Halloween.
I know we're not in our usual attire,
but that's because in between trick-or-treaters the grind doesn't stop.
I guess just be, you were fine just to be enthusiastic.
I think you were doing fine. I'm usually good at being enthusiastic.
And I'm telling myself, I know it's a blooper.
It's going to be a good one.
What? Nothing.
All of the products in you'll serve.
We love to watch all of our favorite TVs and movies.
All the TVs. I know. I'm sorry. I'm sorry.
And it feels like we really made it our own.
For sure. I can name every title on this bookshelf.
