Building a Wood Thin Blue Line American Flag __DREMEL CARVED STARS__

Break Free Homestead
52 followers
29 Video Views·Jan 4, 2023
Thanks for coming to the channel, I'm Steven with Break Free Homestead.
Today's video is about making a subdued thin blue line wooden flag.
It's super easy to make and this really applies to if you're making a red flag or even just
a regular American flag.
If you would, please consider subscribing.
I make new content every Friday, so just drop down below, hit that subscribe button and
the bell notifications.
You need a 1x10x10, a stencil for the stars, unless you're pro and don't really need it,
but this is 15x10.5.
This is made on a Cricut, but you can get some on Amazon so you don't have to do the
work.
A little bit of wood glue, a little bit of True Blue Minwax Stain, this is mixed by your
paint people.
A few razor blades, a couple carving Dremel pieces, I'm using 192 and 107, a little bit
larger and then for the more detailed parts, 107.
A little bit of picture wire to hang it at the end.
You're also going to need a torch if you want to make a burned effect.
You could just buy these 1x2s and it would be the right dimensions, you would just need
to cut it to length, but if you have a table saw, which we do today, you can buy this big
piece of wood and it would probably be a little bit cheaper for you.
Alright, time to get the chop saw plugged in.
We're going to rip this down to 37 inches.
Alright, just cut the board into three 37 inch pieces.
Only got a little scrap piece right there, so now time to get the table saw out and we'll
rip it into inch and a half pieces.
Screw that on more.
1x2s cut.
As you can see, I'm not really working with that much space, so at this point we're going
to put the table saw away and move on to a regular table and start to assemble a little
bit.
So I have my 13 pieces we cut laid out.
When you try to organize them, just remember the stars are going to be up in the top seven
up here, so the less knots and whatnot up in that area might be easier when you're carving
the stars.
What I'm going to do now is I'm going to sand it just real lightly on the top, get any of
the pencil marks off, any abrasions that I think will affect it, and then we'll get
to staining.
Just one thing to remember before you start this process is to check the ends, you know,
you're going to have your board markings on the ends, just make sure you sand it off,
it just gives it that extra touch.
Obviously, if somebody sees this in the end, they're going to be like, oh, he didn't even
check to make sure it was all good.
And then on another piece, I had a staple from one of the tags, just make sure you get
that stuff off.
We're using premium wood here, so nothing too serious, just get your orbital sander,
220 sandpaper, hit it real good, and just make sure there's nothing crazy on like pencil
marks from when we cut it.
Like I said, super quick sanding, we're going to drop this down on the concrete, put some
pieces of wood behind it so we're not burning the floor, and then we're going to cook these
a little bit.
Let's do it.
Just make sure you're not over-burning it when you do this.
All right, we just got that done.
I'm happy with it.
My burner sucks.
It's not supposed to be inverted, so that's probably the reason why it wasn't working
so well.
But overall, I'll be getting a new one of those, and I'm happy with the results.
Let's pick this thing up and see if we can get some stain on it.
This is going to be the top left corner of the flag with the stars.
So what we're going to do, just even them all up, edge over here, we're going to measure
15 inches, 15 on all of them.
You can separate these now.
What we're going to do is we're going to use the razor blade, just put it on the line and
tap it in gently with your hammer.
We're just going to stain both sides at the same time.
This is going to separate the stains.
It shouldn't have any issues.
A lot easier than doing tape.
Like I said, Reason Minwax, True Black for all the black, and then the True Blue stain
for the blue piece.
I'm just going to be using the auto shop rag, usually just rip it in half and it works pretty
well for the stain.
Blue's all set, looking pretty nice.
The sides don't have to be perfect on the inside pieces, just obviously a little bit
in case there's a little bit of a gap.
But the only ones you really have to worry about are the ends and then the top and bottom
piece.
Now all the pieces are stained, we're just going to let it dry for a little bit, and
then we'll put it together and get that stencil started.
Alright, so what we're going to do next, we're going to flip it over, throw some strapping
on the back.
We're going to use four, one on each side and then a couple in the middle, and then
we'll secure it all together.
Due to the fact that my plastic table is not 100% level, I brought it down into the concrete
foundation.
I put one piece of scrap wood on each side, they're just the extra shortcuts from when
we ripped these 1x2s in essence.
But we'll go ahead and squeeze these together, and then staple it together.
Tracing each of these stars one by one is very meticulous, so what we're going to do
is we're going to put our stencil down, cover up the rest of the flag, and just quickly
mist these stars with white paint, let it dry, and then we can come back and dremel
them out.
As you can see, that went pretty fast, and it's a pretty good stencil for us to drill
out now.
So we just did the first line on each star, the paint is working out pretty well, it's
super easy, you just go until it's gone.
Alright, all the carving is done, and now it's time to burn these stars.
Super easy, the stars had no problem burning.
Alright, all the burning is done on the flag, we're going to put the mount, the hanger wire
on the back real fast, and then we'll spray it with poly a few times.
Alright, I'm just going to use this picture wire, and we're going to put a couple screws
here, and then make it simple.
I don't really like mounting two separate points, because then you have to do two screws,
and this way you can just adjust it by hand if it has one mounting point.
So we'll just do either side, and then wire around.
Alright, two screws, a little bit of wire.
You don't have to go too extra on this.
Nobody's going to be climbing on this thing, or nobody should be climbing on this thing,
so it should be all set.
Alright, we just got this thing dusted off, we're using the Minwax fast drying polyurethane.
This project is a great gift, it's super easy, which is nice, you don't have to be some advanced
woodworker to make this.
You could do it in a day, relatively cheap.
That's all today on Break Free Homestead.
Thanks for watching everybody.
Make sure you hit down below, subscribe and like button.
Thank you.
