BUGATTI – A NEW ERA: Extreme Conditions pt. 2

Supersportwagen Daily
222 followers
AI Generated·May contain errors
Video Summary
AI GeneratedDani Rios, a Vehicle Development Engineer at Bugatti Rimac, leads extreme heat testing in Seville, Spain. The sessions focus on validating the cooling systems, powertrain stability, and cabin comfort of a VPP prototype in temperatures exceeding 40°C. By comparing real-world data from track and road tests against simulations, the team ensures the vehicle performs safely and comfortably worldwide.
I'm Dani Rios, Vehicle Development Engineer in Bugatti Rimac,
basically in charge of organizing the testing sessions,
the preparation of the car, instrumentation, testing sessions like
this one where instrumentation is really important
to make sure that all the instrumentation is working
and is meeting the requirements to what we want to test, and finally
the execution of the test in the location where it's taking place.
We are reaching more or less every day temperatures well over 40
degrees. We are here to test the car in these extreme hot conditions
and make sure that all the systems are performing as they should.
Welcome to the south of Spain. We are currently in Seville.
We are here to test our car. Today we
are on board of one of our Protos.
This is the VPP phase, so we have VPP 10. Everything started
approximately 15 months ago.
We were in Dubai with plus 50 degrees on the XPS vehicle.
The main points that we are testing here
in this hot climate testing are three.
On one side, we are calibrating the HVAC in the cabin
to make sure that it is comfortable for driver and passenger
when we drive in such extreme conditions.
We are also testing the temperature on the main critical components
and different vehicle areas.
We have all over 200 thermocouples installed in the car
to make sure that all these temperatures are controlled
and are remaining safe during this testing.
Finally, we are also validating the cooling systems in the vehicle.
We are driving the car in different conditions,
so we are driving on track,
we are driving on the road, high speeds, low speeds,
to make sure that the car remains cooled
down and all
the temperatures again remain within safe limits.
So we have the V16 and of course we
have also the powertrain that is hybrid
and contains as well the 800 volt battery.
Plus, we have three electric motors,
two in the front, one on the rear, the gearbox,
and it's quite difficult to put everything together
because it's quite powerful. There
is a lot of cable, the space is quite tight,
so the car doesn't really breathe that much.
All these powertrain components
are high performance components so they all reach
very high temperatures.
The main challenge here was to be able to cool down these temperatures
while also maintaining such an outstanding and sleek design on the car.
In order not to compromise
the shape and the design we have very clever cooling circuits
and cooling systems inside the
car to make sure that all
the systems remain under controlled temperatures.
When you have a lot of power
But you don't feel comfortable on the track or on the road.
It's very difficult to be precise, no?
So it's very important to keep the comfort in the cabin
and the temperature in the cabin quite fresh
to allow you to allow the customers
as well to enjoy the car at its best.
These two testing sessions
are very interesting testing sessions for us.
We are delivering cars all over the world.
We have customers from lots of places.
They are going to drive their cars in different conditions.
We need to make sure that these cars perform properly
in all these variety of conditions.
Compared to the winter testing session,
a critical point is the cabin temperatures.
In this case, in the opposite way,
we need to make sure that we heat it up properly.
Here in Sevilla, we need to make sure that the temperatures are cool.
down and off but in any case the target
is to make sure that the cabin is comfortable
for driver and passenger.
It's a completely different kind of test we can have 45 degrees
on the open road but we cannot push the car that much as i did before
or consistently at those
speeds so we need the racetrack
and in the racetrack we have a completely different
environment also what you're doing
on the racetrack you cannot do it on the
road because you are not eating up the tires you
are not eating up the brake system.
You are not eating up basically the full package of the car,
so it's very important that we make
sure that when you fully push the car to its limit on the racetrack,
the car reacts in the
same way that we see on the public road.
I hope that our customer will enjoy and experience both
case scenarios because it's very nice.
The car is really, really cool to drive.
Make sure about this,
we have all this extensive instrumentation in the car.
We have also live measuring devices
that are broadcasting the measurements that
we are getting inside the car out to our team
that is also checking the live data
while we are on track and in this way we
are just making sure that all the temperatures are good and
if they are not good they quickly let us know and we stop the test,
we check the data, we do the fine
tuning that is needed
and we go again.
Quite amazing
and the cabin it's very
very pleasant to be on it.
And the HVAC is still blowing the same amount of air flow,
same amount of temperature, so everything is stable.
No differences. Very, very good.
We were able to collect all the data that we wanted.
We were able to validate most of the systems
that we were planning to validate here.
In the end, nowadays with simulations,
you already get a lot of information
of how the car will behave in certain conditions.
What we are doing here is to make sure
that what we saw on the simulations
is actually happening on track, and that's how it is.
So we are very happy that we collected
the data that we were supposed to collect,
that we can see.
on the results that all the effort from all
these previous years is paying off.
So overall, a successful testing session.
