Red Resin and Wood - Swamp Stick Vase

Artistic Strokes
2 followers
1 Video View·Nov 20, 2026
AI Generated·May contain errors
So what I got here is I'm going to do a couple of different vases.
Now, one of these is going to be a
collab with Jake Thompson, Southside Customs,
I believe is what it is, but we will put his link
over there to his channel. I'm going to pour this.
We'll get it into pressure and we'll get it off to
him and into my video, we'll put up a link for the video for him.
I'm doing this one so you all can go over
and check out and see what I did.
So going into the pressure pot,
it's the last time you're going to see it here
until Jake turns it over there.
Good luck, Jake.
Ha ha ha ha!
So anyways, that one will probably be green.
I've actually got some Flo Green warming up
so that it's a little more pliable to use.
And I'm going to use this Apple Green in it.
And the one I'm doing is going to be a red.
I just read some, quite a few suggestions on
hey do some red in one of those swamp stick ones
so uh what kind of wood this is i don't know i've
also had comments on what kind of wood
is swamp stick i've never heard of it
well unknown species i found in the swamp it's a stick
so swamp stick and i might try a little
bit of this interference interference red
from Alumilite along with their red so let's get that
So we're going to use the two-to-one.
TotalBoat High Performance Epoxy Resin with a slow hardener.
Okay, so fluorescent green, a little bit of apple green.
It don't matter which one I do,
so I'm just gonna do this one.
And what I'm gonna do is go about half of this,
put this one in, and I put the other half of that in.
Whatever else I have left over,
I've got, you know, solo cups or with stuff in them.
I'm a little worried about it floating,
so I have tape just in case.
I might not have enough, I don't know.
And this is just for a little bit of a sparkly swirl
and to hopefully enhance the color.
I think I'm going to be good unless they start floating. Now
hopefully when I put this in it does the swirl,
thins it out some so it isn't really concentrated
and things are floating.
I see them, they're trying. Here they come. Well,
we knew that was going to happen.
Look it, they're escaping. I was somewhat prepared.
This time, I still need a foot on it, but that filled us right up.
Top it off a little, and I'll put a piece of HDPE on the top
to hold them down and get it in the pressure pot.
All right, so change of plan.
I'm going to go with this red instead of the interference red.
I think up against the red dye,
I don't think the interference red would work very well.
So I'm going to put this red in if I can get any of it out of here.
And this is just kind of for a swirly effect.
I'm gonna put some more red in this. I already mixed that one up.
I got it all over now.
Ha, ha, ha.
And again, I'm gonna have to move
these around a little I think.
Red first. Not that y'all can see because I'm in the way.
And that's not mixed good enough. I see powder.
These sticks didn't take up quite as much room,
so I'm obviously going to need some more.
All right, so I'm going to mix up a little bit more,
get it in the pressure pot, and then we'll
get it on
a lathe.
Almost
there.
This
stuff's
kind
of punky.
We'll get
this
rounded
so it
ain't
hopping so bad and we'll get a mortise.
Can you guys see what's going on? Anywho, I'm going to
finish straightening this out.
I'm not quite sure what I'm going to do with it. Maybe just
A swooping vase, like so.
I'm hoping these problems are only superficial right here.
I'm not quite sure what to do with this one.
And as soon as I get this smoothed out,
I'm gonna try to hit this with a bowl gouge
and see if I can get a better cut than this.
It's not really hopping too bad.
I should be able to do it.
Hey,
well,
this
is a
bit
wobbly.
I'm not quite sure why.
I'm hoping that's deep enough.
I'm hoping that...
It appears I'm cupped just enough. That ain't touching.
So I'm hoping I can hold on to this.
Yeah, we should be alright.
Anywho, I'm going to get this sanded up.
I'm not sure I might write.
pull burn in there if i can i'm not real happy with that right there
so i might put some CA glue
in it while i have it off oh i gotta go deeper all right
so i'm gonna get that all done i'm
gonna cut this deeper and not force you to watch it
and hopefully i can get that stabilized a little
bit and that way because this is bugging me it needs
to be a better cut than that okay so i am
going to put the cellulose sanding sealer on it i'm going
to do a couple coats just to try to seal
I'm going to use the abrasive paste
and then I'm going to clean this off with acetone because I'm
going to spray this with lacquer and the oils
and the wax and the abrasive paste won't allow
the lacquer to adhere to it.
This stuff is pretty hard so I want to get it a little smoother than
what it is and I'll make sure she's sealed up
and I did manage to get pull burn in there.
It's not great
but it's
in there.
Okay now I'm
going to take
the excess off
a little bit
of acetone
so that my lacquer sticks to it.
all right so slow as i can go is 100 RPMs i'm gonna use the lacquer
and give it a few coats
i'm gonna make you watch one and hopefully i
uh don't get any runs and i will let that dry
it looks
a little thick
in the center
bam wow that
stuff's really
hard that is i
might have
to mix up some resin it's not going to really match
but a big hole in here too
that should turn out i don't know about these
This one looks like it goes up up to here.
I might have to mix up some resin to get in
to fill in some of these. We'll see when I get there.
Right now I got to sharpen some tools.
So I've reverted to a scraper.
It seems to cut easier. I'm really leaning on that
bowl gouge so for right now I'm just roughing this out
and this is going to work. I do have to make
some repairs. Quite a bit
of repairs as you can see. Oh I'm
not sure how I'm going to do that.
What was that?
Doesn't sound like any fun.
Hopefully Jake isn't having these problems,
or doesn't have these problems.
Kind of cool looking, whatever kind of wood that is.
Almost resembles oak.
It's pretty
hard, that's
all I know.
All right, so I have like seven inches.
I threw my Sharpie on the floor.
Ah, I'm about seven and a eighth, by the looks of it.
Right about there is center-ish.
Mr. Higgins suggested break out the carbide.
All I'm really wanting to do is try to get rid of that.
I might be able to get rid of most of that one.
I'm going to have to fill those.
I'm going to have to fill some of that.
Hopefully I can get this tear out to go away.
That's from using the scraper and the carbide cutter.
All right, so I think I can make that go away.
That's going to be a problem right there.
I'm pretty sure it runs right down to here
or somewhere in that general vicinity.
I got another hole there.
One after another.
So what I figured out was I'm going to use the fast set resin,
the two to one epoxy fast set,
and then I'm going to try and recreate that.
You know, it's never going to happen, but
I'm going to try it. So I got the aluminite red.
I'm just going to put a little bit on here,
put it in there. And then a little bit of this one,
the powder that I use,
and we'll see how that works.
That's what I've got a little bit of mica powder in there.
and the red. what i am going to do is i'm just going
to dump it into into these and then hit
it with the little a little torch
and see if i can get it to flow down in there this stuff sets
up pretty quick so anyways you get
the idea this is going to take me
a while wait wait for this to
set up and then go from there you know see if i
can touch some of these up with some super glue
get this sanded up and we'll get into drilling
a hole in this end i don't like that either
I'm trying to get the inside of this,
not quite sure what I'm going to do with that yet.
I guess I could take it down a little bit more maybe.
Yeah,
let's
see.
It's okay though, right about there, and it's just straight down
from there, so I can't reach in any further.
I'm going to try to smooth this out a little bit better,
get it sanded up, and we'll try to get a finish on it.
It's 350
with some
80 grit.
Let's see if I can smooth that out in there.
Maybe a new piece of 380, or 80 grit.
Alright, so that's what I'm going to do.
Try to get rid of these chatters, see them?
I don't know if you can see them.
I think you can see them right there, but I'm going to try to get rid
of all that, get it sanded, and we'll see if we can get a finish on it.
So I'm just going to try to seal it up and we'll go from there.
I'm going to run the axe
and then I'm going to clean it off with,
well I'm going to try to use denatured alcohol.
Probably not a good idea, but that's what I'm going to do,
some lacquer sticks to the outside of it.
The inside I'm going to coat
with resin to seal it. It's
a little more translucent than what it was.
It was.
That really changed how it looks, didn't it?
There you go.
Where you guys going? Why are you falling down?
You were supposed to be up here. There you go.
I don't see how that looks a little better with a light in it.
That's what I got to fix right there. Let's see it.
Just an air pocket in there.
But okay, I want to get this cleaned off and then
And...
break out the lacquer.
Okay, I'll wipe this down with denatured alcohol.
Hopefully get all of that off of there.
So my finish actually sticks to it this time.
Is that your name?
Looks good wet. It'll look really good with the clear lacquer on it.
All right 100 rpms. We're going to start from over there.
Just I'm going to hit that so I don't have any over spray on it.
We're going to go this way and just over the edge.
I don't really want to put any on the inside
so I'm going to coat that with resin.
All right so it's been drying a couple hours
or so however long it takes for
Wayne the Woodturner's live feed to go on on Monday nights.
Now that it's over I'm back out
here I'm gonna put the second coat on it.
Right now I'm just taking up all the the air and that
comes up sometimes leaves little nipples on here
and I'm just knocking them off. We'll put another
coat on and we'll just build the coats until we get it sealed up
and looking like glass.
Yep and again 100 rpms
and we're just going to keep it wet on the back side this way.
As we go across but I gotta move around
so I can catch that glare of it. Gun's plugged up.
I shouldn't have that white line out front that's oversprayed
because I got too much air and not
enough material coming out. I'm not sure why.
All right I'm gonna put I'm gonna put
this one
on while it's wet. It's not real wet but it's wet.
It was just a bit too thick in here. I
didn't thin it enough.
It's a guessing game you know.
It's more better.
That's a little better.
I had to break out the big guns to get a better finish on it.
Apparently I wasn't pushing enough through so I broke out the
The real paint gun to do this and I got a nice finish on it now,
so I'm gonna let this set up and cure and
And...
Then we'll get to seal on the inside of it.
I'm gonna fix that hole in there
I'm not gonna make you watch it and yeah, then we'll get it over there
over there and
Look at it talk a little more and we'll put all
the links up shoot you over and Jake to see what he did with
his half of this project mixed up a little bit of
Total boat tabletop epoxy just to seal this so to speak waterproof.
So anyways, I only mixed up
10 and 10. It's a one-to-one mix.
I am going to pour it in here and then just paint it on with the
paint brush. I don't really want too much
because it's going to keep running back down so
the idea is to just come up around
the edge here seal everything.
So anyways, you get the idea. I can't see what I'm doing with you guys
in the way, and you can't see what I'm doing with my hand in the way.
So, we'll be back when it's all done.
Looks like I hid everything down in there.
And we'll let it just sit.
This stuff flows, levels out,
and most of those bubbles down in there should pop.
And this seals up all the wood, seals the bottom.
It should be watertight.
Go check out Jake, Northside Customs.
I'll leave his link.
Well, his link was earlier,
so I'll put the link for the video at the end in the pictures.
So we're going to stick Jake right up here on the board.
Y'all can scooch over and see how he did on the other half of this.
You know, it is what it is.
It's not perfect.
It must have had some moisture or something in it.
I don't know what's going on with the finish after.
I don't know if y'all can see it.
It's got...
I'm not sure what's coming out of it, so I'll let it cure up
a little bit more, and I'll probably put another coat of lacquer on it,
because I'm not quite happy with that finish at the moment.
It looked good yesterday, but anyways, there it is in red.
I will put a light in it, because everybody wanted me
to put a light in the blue one.
We did put a light in the blue one I just didn't show you.
So I'll set a light in this so y'all
can see what it looks like with light in it
but it was supposed to be a vase not a light. So swamp
stick in red as suggested and we'll put a light in it as suggested.
So you know thumbs up or
thumbs down. Go on over see what Jake did
with his half of it uh the link for that
video is coming up real soon.
I don't know what else to say to him about it I had some problems.
I tried to keep it all in there.
After a day, I'm not real happy with the finish on it,
so I will probably do that, redo that.
I got some other projects coming up.
I got a pile of stickers to put on this board.
They'll most likely all be up there
because they weren't sent to me by those people,
but by somebody else.
So we'll get around to it.
How's that?
We'll see you all next week.
Go check out Jake.
