How to build a Mini DIY Greenhouse for THRIVING Transplants

Architectural Course
8 followers
Nov 16, 2026 #Architecture
AI Generated·May contain errors
Video Summary
AI GeneratedThis video explains how to protect early spring transplants from frost and cold snaps using two types of DIY mini-greenhouses. The goal is to trap heat and maintain a warmer environment than the open air, ensuring plants thrive during the transition from indoor grow lights to the outdoor garden.
Hey folks, so it is mid-April and I'm in zone 7b
and this morning we got frost.
And so we're always at risk
of potentially getting some later frost in the season.
But by utilizing structures like this,
I've been able to already start moving some of my transplants outside.
So today what I want to walk through are two mini DIY greenhouses that
you can be using to help your plants thrive from day one this season.
Alrighty, and as we get started here, if you have any questions
at any point, just leave those down in the comment section.
I start every one of my days by having a nice hot cup of coffee
and answering every question that we get on YouTube,
so you'll get a response from us within 24 hours.
Now, the question really becomes, like,
why do we want to utilize these DIY greenhouses?
And ultimately it all comes back to warmth.
Our plants love a warm environment to be growing in.
So when we think about
those that we started inside underneath the grow lights,
the temperature there has been 20 Celsius for all
the daytime hours as well as all the nighttime
hours. But when we move them outside into the garden,
especially in early spring,
there are going to be days where it's rainy
and colder than that during the daytime.
And at nighttime, there's potential for it
to even be dipping below 10 Celsius.
But by utilizing these mini DIY greenhouses,
what we're able to do is essentially trap
air right around where those plants are.
And let the sun heat it up and by utilizing
my min-max thermometer what I've seen is that during the daytime
this can be as much as 10 to 15 Celsius warmer than without it.
But then also at nighttime what I've noticed is that these structures
are helping to keep that environment 3 Celsius warmer.
than the other beds that once again are not protected
and that can really be the
difference between a plant surviving
through a little bit of a cold snap or
ultimately not making it through that period.
So the first DIY greenhouse that
we're going to build is the one right
behind me here and what we're going to
do is first go through all the supplies
that we need for that. Let's get to
building. So the materials
that we need include seven 48 inch pieces of wood.
Four 36-inch pieces of wood, two 34-inch pieces of wood,
and four 32-inch pieces of wood.
And then poly for our barrier, staples
and screws for connecting it all, and hinges for opening the top.
And as we get started here,
one caveat that I'm going to make is that I am not a carpenter.
I am not a very good woodworker.
So what we're going for is function here.
And if you want to make things prettier on your end, definitely do so.
But that's not what you're getting with this video.
So what we're going to do first is connect two
of the 48 inch pieces of wood to two of the 36 inch
pieces of wood and this is going to serve as the base
of the greenhouse. So all that I need to do
here is pre-drill two holes and then grab two of the screws
and drill those in. I like to go with
three inch screws so it's nice and secure
and after that first corner is connected you're just
going to go around to each of the other corners
and do the exact same thing so that those first
Four pieces of wood are connected.
And so with that first part of the base finished,
you can pop it to the side
and then we're going to repeat the exact same process.
So two more 48 inch pieces of wood
getting connected to two of the 36 inch pieces of wood.
And now with both of those put together, the next thing for us to do
is to connect them to form the base of our DIY greenhouse.
And for this we're going to use our four 32 inch pieces of wood.
So connecting the first one can be a little bit tricky,
but all that you need to do is basically take
the top of the 32 inch piece of wood,
line it up with the frame, pre-drill the two holes,
and then connect it to the frame with two screws.
And so once that first one is in place,
the remainder are really quite easy.
All that you need to do now is line up the bottom,
pre-drill the holes, screw it in.
Easy peasy.
And so then once you have the first two connected, you can flip it over
and then connect the other two 32-inch pieces
of wood to the bottom side of the frame.
All righty, starting to come together.
So next up is wrapping it in the poly.
And what I like to do for this is measure out a piece
that I know will be big enough to wrap all the way around
so that I'm only connecting one piece of poly to the frame.
Makes it a bit stronger.
Once I've measured that out,
I cut it and drape it over the top of the frame.
And there's gonna be a lot of excess at the beginning,
so take your time with moving it around
and be a little bit patient with it.
And all that you need to do here is essentially square it up
so that it's running parallel to the frame
and then pop a few staples into the poly to secure it to the frame.
Then go over to the other side of that one panel
and pull it tight so that there's
as little slack in the poly as possible
and then staple that side to the frame.
Then you move on to the next panel and you do the exact same thing.
Square it up, staple the first side onto the frame,
pull it tight on the other side
And then staple it to that far side.
And then you do the exact same process for the third panel.
Super straightforward.
So once those first three are done,
you can then gently lift it up
so that you can access the fourth and final panel
and repeat the stapling process.
And at the end of this, all four sides are wrapped
with bottom open for where the plants are gonna go in
and the top open for where we're ultimately
gonna connect that hinged roof.
But there's tons of excess poly here,
so grab a pair of scissors and cut it down leaving about six inches
of excess that we're going to be stapling to the frame.
And so with this excess poly, all that I like to do is simply
roll it over and then staple that to the inside of the frame.
And I'm sure there's a cleaner and more
aesthetic way of going about this.
But again, folks, I'm going for function here.
And so you're going around the entire frame,
just taking each of the little excess areas
and stapling it onto the frame until the very end.
It's all stapled down.
And sure enough, it's starting to look like a DIY greenhouse.
So the base complete.
Now we need to get started on the top.
And for this, I'm going to grab two of the 48-inch pieces of wood
and connect them to our two 34-inch pieces of wood.
And then it's the exact same process in terms of pre-drilling two holes
and then popping the screws into each of the corners.
Now, one super important tip that I've learned the hard way
is to make a tick mark at 12 inches, 24 inches,
and 36 inches on the 48 inch piece of wood.
And we're going to run three strips of wood
across the top of our roof at these intervals.
And the reason for this is because as it rains,
the water would pool up on the top of the DIY greenhouse
and ultimately get too heavy and rip the poly.
Trust me, I learned this one the hard way.
So with those three pieces connected to the top, all that I need
to do now is measure out a piece of poly to cover the top,
staple it down, and then begin to make sure it's square and tight.
Then I cut away the excess just like before,
flip it over, and staple that little bit
of extra excess to the bottom side of the roof.
And voila, our top is all complete.
So let's now pop it on with the hinges.
So to do that, I'm going to grab the final 48 inch piece of wood
and connect that to the back of the frame.
Next, at 16 inches in,
I'm going to connect the first hinge to that back strip.
And then at 32 inches, I'm going to connect the second hinge.
And so once those are connected,
I can now grab the roof and slide it onto the DIY greenhouse.
I want to make sure it's nice and squared.
And then all that I need to do is simply connect
the hinges to the roof with a couple of screws.
Alrighty, moment of truth.
Does it open?
Oh, baby!
I mean, come on.
Love it.
All righty, let's pop the top of where I'm going to put some leafy greens.
All righty.
And now this greenhouse is all set, ready to go.
We are ready to begin transplanting into this bed right beneath it.
And there's two reasons why I really love
this kind of style of DIY greenhouse.
The first one is that we can cut the wood to any size that we want.
If you're working in a smaller raised bed, a larger raised bed,
you can make those adjustments
and on top of that you can make it as tall as you like.
And the second piece that I really love about
these types of DIY greenhouses
is of course the hinges because now on those really hot days,
I can just open it up like that and it's going
to be able to let any of that
excess hot air out. I don't need to be moving it around.
Really easy. Takes all of, as you saw, two seconds.
But it's taken me several hours
to put together and some power tools that maybe not
everybody has. And so this is why I absolutely love
the second option. You're
going to be blown away with just kind
of how simple it is and how quick and easy
it is. And so just before we get to that,
for those of you that I have not met
before, I'm Jordan from Mind & Soil where we're
We're looking to introduce
A million individuals to mindful gardening.
So if you're looking for more peacefulness,
more joy, more restoration in your life,
then I really encourage you to subscribe to our channel here
because on top of the occasional flesh wound,
We put out videos every single week to be taking
as much of the guesswork out of gardening as
possible so that you too can be experiencing just how peaceful calming
and restorative it is. So now
with that being said let's get into our second
and final DIY greenhouse and on this front we
basically need nothing whatsoever.
All that we're doing is driving back to that same hardware store
and then we're going into the storage area
and all that you're looking for is a clear storage tote
Effectively, exactly what we're looking for in a greenhouse.
A sturdy structure that's nice and clear,
going to let that sunlight in.
One tip here is to go and find the tallest one that you can.
And now that I'm back at home,
all that I need to do is drill a bunch of holes into it,
and we are off to the races.
Alrighty, so drilling those holes I think took about 10 minutes.
On top of going to the store,
I think we're maybe up to about 18 to 20 minutes in total.
And with that, this mini DIY greenhouse is all set, ready to go.
So let's move it over to the garden.
And voila. So just like that,
this one is into the garden doing its thing. So if you're looking
for something simple and easy, this is 100% the route to go down.
Now, with that being said,
the one drawback on this one is that there is no way
to open up the top of it. So it will get hot
really, really quickly. And because of that,
you're going to want to utilize either a regular
thermometer or a min-max thermometer inside of it.
So that you can familiarize yourself
with just how warm and how hot it's getting in there.
And on those really sunny hot days,
all that you're going to want to do
is either open it up completely
or pop a little stick into the ground
and then you can rest it on the stick just like that.
And that's going to allow some of that warm air to move out
and then you can put it back down and closed
as you get into the evening time.
But folks, if you utilize these mini DIY greenhouses,
your transplants are going to absolutely
be loving you and thriving from the beginning
of their time in the garden.
So if you do have any questions,
go ahead and ask those down in the comments.
I'll be sure to get an answer to you straight away.
Other than that, can't wait to catch you on the next video.
And until then, go get those hands dirty.
