Samus 725MP Electrofishing Part 1 - Set Up

Pondguru
22 followers
1 Video View·Nov 7, 2026
Similar electrofishing unit: http://geni.us/3VUw
Electrofishing the pond part 1: https://www.youtube.com/watch?v=Kn5D5DhHgb8
Electrofishing the pond part 2: https://www.youtube.com/watch?v=cBb285u96pM
Apologies to anyone who viewed my previous set-up - I deleted it as I filmed one of the wires in the wrong place.
This is the correct way to set up the Samus 725MP electrofishing unit.
AI Generated·May contain errors
Hello there. This is a very quick
video showing the setup of this fella.
It's a Samus 725 MP electrofishing unit from Samus Electronics.
Apologies to people who watched my previous video on this subject.
I actually had one of the wires in the wrong place
and I didn't realise, even after editing it for ages.
Just so.
That video has been deleted.
This is the new one. This is the proper one.
Right, the Samus has two wires coming out of it.
One's red, one's black.
Ordinarily they'd be separate wires.
I've taped these two together all the way down until about a foot
from the end and that keeps them nice and tidy but it also
allows them to be splayed apart and attached to a car battery.
So they're the wires that are fixed.
There's two wires that go to your net. The black one goes
on the positive and that goes onto the ring of your net.
Is this fella?
This goes...
Marked start and the other end
of this has a switch on.
I've taped that onto my net
and that is used to put a charge through the water,
basically to allow the machine to work.
When you depress that, power flows
from the battery through this unit to the end of your net.
Bang, zaps the fish.
So in a similar way to the two wires
which are fixed on the electro fishing unit,
I've taped the switch wire
and the positive wire
All the way down, just to keep them nice and tidy, they're pretty much
the same length, so it's worth doing that to keep them tidy,
and they run in the bottom end of the net handle here,
and I've used pipe insulation over the handle, and in the little valley
that's created in there, I've just run the cable up all the way
to the end, this is the positive cable, and it wraps around.
A copper wire which goes all the way around the net.
This particular net doesn't have an aluminium loop
which runs all the way around.
It's got a little bit of aluminium,
but it just goes from the shaft to the end here.
Doesn't go all the way around.
So I've used a copper wire all the way around,
linked my positive to that, and it works pretty well.
So by taping that on in that position,
it allows me to use my left hand or my right hand
to switch the machine on.
And by insulating the handle,
Just keeps everything nice and comfortable and safe.
The only other wire that you need has
this mass of braided copper on the end.
This is what hangs out the back of the boat
or trails behind you and this is the negative.
This is a really long cable
and this end goes to the negative there.
So positive to the net, negative trailing behind you,
switch plugged in there, positive
Positive and negative on the battery and you're ready to fish.
Just a quick note on the battery that I'm using.
This is actually out of a four-wheel drive,
damn heavy battery, and that's
the details of it. 700 amps,
12 volts, 75 amps, amp hours,
20 hours. It's a beast of a battery
and it should last a hell of a long time. You should see the
machine come on here as soon
as these are attached.
That's it, the machine's on, you
you program it and fish.
In the next part of the video I will actually be doing some fishing.
I have actually been out fishing with it already with mixed success.
It was my first time out.
I tried it by myself and paddling the boat
and using an electro fishing setup is very very
difficult so I had my two children helping me
and it was only marginally easier. Tomorrow I've got
one of my mates coming and we're going to give it a real good go
and providing it isn't raining
We should get a decent bit of footage for part two.
