Making a Working Lego Pendulum Clock !!

Lego Happy Time
8 followers
9 Video Views·Oct 28, 2026
This is a fully functioning LEGO pendulum clock. It lasts up to a full hour! I really made an improvement on the lego mechanism. (enjoy the ASMR lol) If you enjoyed, please leave a like, and subscribe to not miss any content!
AI Generated·May contain errors
So you guys really liked the last time I tried
to make a mechanical LEGO clock,
even though it only lasted for 3 minutes. So it's time to improve that.
And today, I have a few tricks on my sleeve.
So let's just get straight into it.
I have three goals for this build.
The first is for it to be accurate. After all,
clocks are supposed to tell the exact time.
Secondly, it's for it to last a long time,
maybe at least half an hour.
And lastly, my last clock only had one hand, so today,
I'm going to step it up to two hands.
And if I can meet all these goals by the end of this video,
I'll be happy. But will I even be able to do that?
I guess we'll have to find out.
But for now, you can sit back and enjoy the video.
Wait,
but
what
did I
just
build?
I
have
some
explaining
to do.
So now I need to make the escapement mechanism.
So the way we're going to do this is with something
that will oscillate at a certain frequency.
This clock is going to use a pendulum, just like a grandfather clock.
The idea is we can use a pendulum to make the clock more accurate,
because we know how long it takes
for a pendulum to swing back and forth.
This gear is only able to rotate in one direction.
So what we want to do is have the pendulum lift
this ratchet, allow the gear to rotate one tooth,
and the ratchet lowers back again.
Again, six years.
So after a lot of experimentation
this seems to work well enough.
As you can see when the pendulum
moves, the ratchet gets lifted
and the gear pushes the pendulum and ratchet back.
And this is lined up pretty well in its neutral position.
And we can attach it to the actual pendulum later.
So now that we've figured that out,
Wait, but what is that weird spinny thing I just made?
It's that time of the video again.
Start with the clock hands mechanism.
Well, if we have two different block hands,
this is the minute hand and this is the hour hand,
and we want them to both rotate at different speeds
on the same axle, I don't know if that's
even possible, but let's try it.
Okay, so my first candidate is this weird gear piece,
and you could probably put it here and have it rotate like this.
You could have an axle running
through the middle, and you could also have this gear
which is attached to this other hand somehow,
but it's quite bulky, so I'm going
to keep looking for some more options.
So this piece seems to be another candidate.
If I put an axle through it, you can see that these
can both rotate individually.
The problem is how do I attach this? And second of all,
how do I actually get it to rotate?
And I actually have one of these special gears
and this mechanism seems to work since it's based
on the fact that this piece sticks a
tiny bit further out than the base.
So these stick nicely in and it rotates with it.
It's going to have to be a bit lopsided, but it should be good enough
and we can still insert and rotate freely a large axle.
So the next step is figuring out how to attach the hand
and I could just do another friction fit mechanism.
But for aesthetic purposes,
I'm just going to attach this with a bit of blue tack and there we go.
You can see that these hands
can now individually rotate. This one has a bit more friction,
which is a little bit concerning, but I'll fix it up later.
Okay, what is that weird gear looking piece?
next priority is to separate these hands
by making them move at different speeds obviously
and all i need to do is make it
so that every time this hand rotates 60 times this hand rotates one
time so that's a pretty big gear down
but first we need to gear this away this can move a lot so
i'm also going to attach this axle through
a hole that keeps it in place it's working so
What I want to do is figure out how I'm going to gear
this down by one-sixtieth and in a small amount of space.
And we have our solution, which is this worm gear.
So I'm just going
to do a quick one-to-one gear ratio.
Now all I need to do is connect the twelve-tooth gear to here
and connect it to this axle with a five-to-one gear ratio.
I was right.
So now we should have the hand mechanism working.
As you can see, the other hand moves slowly.
You can tell that these hands are accurate to each other
and although it was going to be a minute and hour hand,
I decided to make it a second and minute hand
because this clock was probably only going to
last
an
hour.
Circle.
Wow
that
is not
the
setup.
This
is
where
our
chain
is
going
to go
and
this
is where our pendulum hole is.
Let's use a bit of blue tack to hold it
in place. Now it's basically
perfect and okay now that that's attached I can start moving
on to the last part which is going
This is going to be the weights and the pendulum.
To hold the pendulum I'm just going to use two of these wheel pieces.
I'm going to get a bunch of these pieces and attach them to here
until I have the right length so that the pendulum oscillates
exactly one second. So here's one, two,
and let's just start with three. There we go
and let's see how long it takes to oscillate.
So it's a bit faster.
And that's a lot closer.
Add just a tiny little bit more and that's pretty much perfect. So now
I've just realized the problem
which is that pendulum naturally leans a little bit this way.
So what we're going to do is we're going to attach a little piece like
so and just offset the weight
by a tiny little bit and there we go.
So the next step is to attach the weight and I'm going to use
some of these chain link pieces.
So we're going to just thread them through first. We have
successfully threaded it through
and now it's time to attach our weight. Use a drink bottle.
Tada! The board is adjustable
and now we can attach it.
Seems to be not enough weight. Maybe the pendulum isn't heavy enough.
Tie that's supposed to be on this element.
I'm just only going to put the
front tire on. These are under
a lot of stress but the
ticking sound is much louder and it appears that it works. Okay let's
just see how long it can actually run for.
I'm going to reset the weight
and then leave it to run then we can work on some
polishing.
Okay, the time according to this clock is about half past, so let's see
with this unpolished pendulum how long it actually runs for.
While we're here,
it's probably a good time to say,
if you haven't already, please like
the video and subscribe.
It'll really help push this video with the YouTube algorithm,
and this video took a while, so it would be worth it.
Okay, so I think
the clock's almost done.
As you can see, the weight...
is pretty much on the floor
and it's been about exactly one hour since we started this
according to the clock that is so i would say this is a success
so there we go the clock has finished
and now all we need to do is tweak the pendulum okay
so the last adjustment i need to do is to
make this pendulum a tiny bit longer
because it was running a bit too fast so we're just going
to place it with a slightly longer piece plug it
in and let's see if this is the right timing okay
Okay, let's wait till this is at the top.
55, 56, 57, 58, 59, 60.
So it's pretty much perfect.
The last thing we're going to do is add another layer of cardboard.
There we go and I think it's finally time to cue the montage.
