A big design flaw in many gas masks/respirators where there is no internal design to stop sweat from your brow from running into your eyes, a simple curved piece of rubber could prevent this or a more complex system involving silica gel in a bag could also work. Either way having your sweat run constantly into your eyes renders you almost useless with the mask on,
The speaker identifies a design flaw in several military gas masks, specifically the Israeli M15, where sweat from the forehead drips directly into the wearer's eyes. This issue is particularly problematic during high-intensity labor or in NBC (Nuclear, Biological, Chemical) scenarios where the mask cannot be removed. The speaker suggests several design improvements to better manage moisture and improve user comfort.
Hello, so this is going to be a video on a floor I've found in several military masks
now. Now, I was using my Israeli M15 the other day when I was sanding down a bench in the
garden. It was a 30 degree day outside again, so quite hot. Obviously doing manual labour,
I had to have the mask on with a filter because I'm sanding, so there's bits of sand flying
up that could either go in my eyes or be inhaled. Not bits of sand, but bits of chipped wood.
So, sanding that down, obviously I needed the mask on. However, there was a problem. When you
start sweating in this mask, the water keeps going into your eyes and irritating your eyes,
so every so often I'd have to stop sanding, go indoors, take the mask off, dry my face and the
mask off, put it back on and carry on. So, I think there's an easy way this could be fixed,
and this isn't going to be a problem with just the Israeli M15, this is going to be a problem
with several masks. So, if I show you the inside of this mask, what you can see here,
is this is obviously the bit where the bridge of your nose sits on, or this sort of bit of your
head. Obviously, your nose and mouth are meant to be in the oral nasal cup. You have got a bit there
so sweat can go off of your chin down there. But you'll notice there's nothing to stop sweat on
the forehead area like dripping down onto the eye lenses and into your eye. So, what ends up
happening is there's not like an actual sweat channel in the mask to get the sweat out of the
mask so it doesn't interfere. Now, if you're in some sort of military scenario or whatever,
where you have this mask on and you're getting sweat in your eyes and it's causing problems,
there'd be absolutely no way, you know, if it was in an NBC situation, you could take the mask off
to alleviate that, so it's going to cause severe problems. And this isn't going to just be a
problem with the Israeli M15, I just noticed it quite a lot on this mask as I was using it.
So, what I think mask makers might need to do is put maybe a little ridge, like a very small one,
around here, maybe going down on each side of the eye lenses. So what happens is as your forehead
sweats, when the sweat runs down, it actually goes down the sides of your face into the sort
of drainage channels of the mask, not directly downwards, you know, going straight into your eyes.
Because, as I said, once it goes straight into your eyes, you've got a bit of a problem because
it's going to get in your eyes. Now, I don't think I've actually ever seen the mask or I've
noticed anything that's there to prevent that happening. Now, some masks are going to be worse
than others, obviously, depending on how good the ventilation is on the mask and how the mask is set
up. But I did think that was quite interesting, you know, that there is no sort of system in there
as a drainage channel. As I said, there is a bit of drainage in the chin because you can see there
that you've got the hole in that bit there, when you pull that down you've got another hole in the
next bit, and obviously they go to the exhale valve that's there. So the idea being that when
you sweat it just drips out when you exhale. Now, there's lots of 3M half face masks I've used
before, I've not had that issue at all. As I said, your brow's there and they're around there, so that
isn't going to be an issue anyway. But, you know, that do have, some masks seem to have a very good
drainage system in them, so whenever you breathe out you force the water quite quickly out with
your breath. So maybe that's something for mask manufacturers to actually consider, you know, so
you can actually have a drainage system that works faster than others. Now, the Scott GSR, as much as
I complain about it, did have some sort of sweat adsorbent pad in it. However, I didn't think that
really worked very well, because for the most part it just dug in and made the mask uncomfortable.
So, you know, it might drain sweat a bit faster out of the mask, but at the same time, you know,
it's not great for that reason. Now, another thing a mask maker could do is maybe have some sort of
pouch on the inside of the mask. Again, I'm not sure exactly how they do this, I'm not a manufacturer,
but they could probably think this up. Which contains silica gel, because I'm sure you notice
you can actually dry out silica gel. So, what you could do is you could have the pouch of silica gel
in the mask or around part of the area, especially the forehead area would be good for it. So that,
you know, absorbs loads of your sweat for ages, then once you take the mask off you can put it
somewhere so the silica gel dries out and it becomes, you know, reusable again. One of the things I
had in my old car was it went on the windscreen on the dashboard inside when you weren't using
the car in the winter, and it was so when the windows mist up on the inside the silica gel
pouch, you know, absorbs it and then that just dries out on its own later on. And, you know, you don't
have to keep wiping your windscreen down on the inside. So I think that might be a good idea, but
as said, it's something I've not really massively thought about before because I haven't really used
masks. I've done a charity fun run in a mask before, but, you know, for the most part I don't
use masks in like high physical labor sweaty activities where you start to notice when
there's a design flaw in that way. So I still like the Israeli M15. I think it's one of those really
good sort of masks. If you can get it for about £30 it's a pretty competent design because it's
a better version of the M65. However, you know, it could really do with some sort of drainage channel
but as said this goes to a lot more masks than just this one. I can think of loads and loads
of masks that would actually be really improved if they just had some sort of inner face seal that
was very minor that just went like that, you know, around your face like that so when you get sweat on
your brow it goes down your cheeks and not straight into your eyes or next to your nose or your mouth
or whatever else. So something to take on board. I don't know if any mask manufacturers watch my
videos. I sort of doubt it, but if they do I've just given you some free advice on how you might
be able to improve the designs of your masks to work well under heavy physical labour or extreme temperatures.