Flexjet has ordered 300 Phantom 3500 business jets from Otto Aerospace, featuring a revolutionary windowless design. By eliminating cabin windows, the aircraft achieves a laminar flow surface that significantly reduces drag and fuel consumption while increasing structural integrity and reducing manufacturing complexity.
In September 2025, a company called Flexjet signed a contract for 300 aircraft worth around 5.85
billion dollars. The aircraft it ordered does not have a single cabin window. Not a small one.
Not a darkened one. None. This isn't a rendering. The manufacturer became an FAA applicant that
same month, the certification basis is agreed, and first flight is planned for 2027. And the
windows are missing for reasons that have very little to do with what passengers see.
A cabin window is a hole cut into a pressure vessel. Around it, you build a frame. And around
the frame, you reinforce the skin. Because loads that ran straight through the metal
now have to travel around the gap. Scott Drennan, who runs Otto Aerospace, put it plainly.
Window cutouts and the structure needed to reinforce them increase the time and labor to
build an aircraft, increase its weight, and expose the surrounding structure to more fatigue damage
during ground-air-ground cycles. There is an aerodynamic bill, too. Every cutout leaves steps,
gaps, and joints in the outer surface. Otto's aircraft, the Phantom 3500, is built around
laminar flow, air staying smooth and attached along the fuselage instead of tumbling into turbulence.
A clean tube does that. A tube with 30 holes in it does not. Wind tunnel testing in 2024
measured 35% less drag than comparable aircraft. Otto projects roughly half the fuel burn.
So if windows cost that much, why has the rest of the industry spent 20 years making them bigger?
Because they sell aircraft. The Boeing 787's cabin windows measure roughly 10.5 inches by 18.
They are the largest passenger windows on any airliner flying, and Boeing did not treat that
as a footnote. It was a headline feature. Compare that to an Airbus A350 at around nine and a half
by thirteen and a half. The 787 opening is well over half as large again. Boeing also threw out
the pull-down shade. The 787 uses electrochromic glass from a Michigan company called Gentex,
a gel between the panes that changes opacity when current runs through it. On the 777X,
the newest version blocks more than 99.9% of visible light and switches in around a minute
against two or three minutes on early Dreamliners. That is an enormous amount of engineering spent on
making a hole more pleasant. So the direction of travel has been the exact opposite of what
auto is doing, which makes the next part slightly strange. Ask why the 787 could have
windows that big, and the answer isn't glass. It's the fuselage. Older airliners were built
from aluminium sheet riveted over frames. In that kind of structure, every opening is a fatigue risk,
and the size of the openings is limited by what the metal around them can survive.
The 787 is different. Its fuselage is molded as one-piece composite barrels with no rivet
lines running through the skin and composite handles that cyclic loading better than riveted
aluminium does. So Boeing took the new material and spent the margin on bigger holes. Auto has
the same material. Its fuselage is a single composite structure built by Leonardo in
southern Italy, and it spent that identical margin the other way on no holes at all. Same technology,
same decade, two completely opposite conclusions about what to do with it. Only one of them though
gets you a laminar surface. So what is auto actually built? The Phantom 3500 is a business
jet. Two Williams FJ-44 engines, a ceiling of 50,000 feet, a range of around 3,700 nautical
miles, a maximum takeoff weight under 19,000 pounds. None of it can be retrofitted, which is
the point. The whole advantage comes from a surface that was never interrupted, which means designing
it that way from the empty page. Inside, screens run the length of the cabin, fed by external cameras.
Auto calls it a natural vision system and has been putting people through simulator sessions
specifically to test whether a windowless tube triggers claustrophobia. That brings the airlines
into it, because they thought of this first. In 2018, Emirates fitted virtual windows to the
first class suites on its Boeing 777s. Fiber optic cameras outside, a projected image inside.
Passengers in the middle of the cabin got a view they had no physical right to.
Emirates President Tim Clark went further that year.
Windows, he argued, are a real structural problem. A fuselage has to be reinforced to carry them,
and a composite tube built without them would be dramatically lighter. He suggested windowless
aircraft were perhaps 20 years away. That was eight years ago. No airline flies one.
And the reason isn't that passengers refused. Nobody has ever been asked.
Airliners in the United States are certified under Part 25 of the Airworthiness Regulations.
Business jets of the Phantom's weight fall under Part 23. Two rule books. And on this question,
they do not agree. Part 25 contains a line about emergency exits. Each one, it says,
must have a means to permit viewing of the conditions outside the exit when the exit is
That rule is not about scenery. It exists so that whoever opens a door in an emergency
can first see what is on the other side, whether there is fire, whether there is water. Part 23's
equivalent says only that exits must be locatable and openable from inside and outside. So the first
windowless jet is being certified in the one category where nothing obliges it to look outside.
But that gets overstated constantly. The rule does not ban a windowless airliner.
It puts windows at the doors. You could build one with viewing ports at each exit and unbroken
skin between them, and most of the prize would still be there. The real obstacle is that nobody
has taken such a design to a regulator. There is no agreed method for proving it safe. And
proving novelty safe is the most expensive thing you can do in this industry, which is exactly why
it is. Flexjet sells fractional ownership. Its customers buy hours, not a seat beside a particular
pane of glass. And Flexjet pays every fuel bill itself. If half the fuel burn is real, it lands
straight on the operator's own accounts. That is a much easier place to test an idea than an airline
cabin full of strangers. So why would an airline want this at all? Not for the view. For three
things underneath it. Weight, because a structure with nothing cut out of it needs less material to
hold itself together. Manufacturing, because every window is a frame, a seal, several panes,
and reinforced skin that somebody fits and somebody inspects thousands of times across a fleet. And
fatigue, because the places aircraft crack are overwhelmingly the places where something was cut.
None of that appears in a brochure. All of it appears in cost per available seat mile,
which is the number airlines are actually arguing about. The Phantom 3500 will never carry anybody's
passengers. But it is a full scale test of whether a modern aircraft can be built without the one
feature nobody thought to question. For 20 years, the industry answered the window question by
making them bigger, larger panes mounted higher dimming at the touch of a control. Boeing sold
that as a reason to pick one aircraft over another and it worked. Otto's bet is that the
question was framed wrong from the start. Nobody at 38,000 feet has ever cared about a structural
opening cut into the fuselage wall. They care about what it shows them. Passengers were never
asking for a hole in the aircraft. They were asking for the view.