A pendulum clock is a clock that uses a pendulum, a swinging weight, as its timekeeping element. The advantage of a pendulum for timekeeping is that it is a harmonic oscillator: it swings back and forth in a precise time interval dependent on its length, and resists swinging at other rates. From its invention in 1656 by Christiaan Huygens until the 1930s, the pendulum clock was the world's most precise timekeeper, accounting for its widespread use.
For this project we need pallet wood, protective equipments like face mask, glasses, gloves,
sanding tool, hammer, measuring tape, nails, handsaw or chop saw, knife, pliers, pencil and
paint of your choice. For the electronics bit we need a Arduino Nano, a servo motor,
a 18650 battery or a 5 volt DC buck step-down module, battery protection board, a SPDT switch,
a generic PCB and general soldering equipments. Let's start the project by sanding the planks
to give them a nice and smooth texture. Next using a chop saw I'm cutting the two sides,
bottom and the top section of the clock. Once all the sides are ready it's time for me to join them
all together. At first I just used nails but soon I realized it was not a good idea to have just
nails to hold the sides. So I went ahead and added screws to give the sides an additional support.
Using an edge decorative stick I'm preparing the roof of the clock. From its invention in 1656
until 1930s the pendulum clock was the world's most precise timekeeper. Using some of the
leftover wooden blocks from my last projects I'm preparing the base of the clock. To fill in the
gaps I'm adding a bit of POP to the groves. However as we all know too dissimilar material like wood
and plaster expand and contract at different rates. For any sort of permanence you need to
isolate the movement of each related to the other. However this clock is not going to move a lot and
will not be placed outside the house. So adding a bit of POP would not really matter as long as I
seal it properly. I'm preparing the dial of the clock using a board extracted from a broken chest
drawer. My plan is to have a dark colored dial and a light color housing for it.
So I'm painting the dial black. Now for the numbering bit I'm using a printed sheet as a
stencil to transfer the numbers from the sheet over to the circular board. Once all the numbers
are transferred I'm painting the graphite impressions with white color. If you are too
lazy you can just print it out from your computer. After giving the finishing touch I'm drilling a
hole in the center of the circle and placing a two dollar watch circuitry which I bought from
AliExpress. Now from the same compressed wood board I'm extracting another circle which will
be used for the pendulum of the clock. This is how I have created the pendulum's circuit. Connect the
servo to any one of the digital pins of the Arduino. Then connect the negative to ground
and positive to the 5 volt output of the Arduino. Finally connect the negative wire of the battery
to the ground and positive to the VIN of Arduino placing the switch in the middle of the circuit.
This circuit diagram is for the pendulum only. The code is very simple. Start by including the
servo.h library then declare the servo pin and then create an object of the servo class.
In the setup section attach the servo to the Arduino's pin and finally in the loop section we
just need to move the servo left and right. I'll start by soldering the Arduino to the circuit
plate. Then I'm connecting the servo to the digital pin D2 and the negative to ground and positive to
the 5 volt output of Arduino. After that I'm connecting all the cables to the BMC and finally
soldering it to the main circuit board. Now that we have the circuit ready it's time to hot glue
the battery to the back of the clock. Then solder the circuit to the battery. Instead of using a
you can connect a step-down converter here. A quick note AVR are made for low power applications
as low as 0.7 volt. The nanos at greater than 5 volt will work a little slower. Analog pins will
be glitchy and 5 volt and 3.3 volt regulators will provide a lower voltage. Next I'm painting
the body of the clock. I chose off-white color for the body of my clock as my dial is black in color.
I created the back plate from the remaining cardboard bit and screwed it to the back of
the clock. Almost done. To conclude the tutorial I'm hot gluing the pendulum to the servo motor
and then sliding the clock face to hide the circuitry behind it. That's it. All done. Thanks
again for watching this video. I hope it helps you. If you want to support me you can subscribe
to my channel and watch my other videos. Thanks. See you again in my next video. Bye now.