Year 2020, has taught us many new things. Our lifestyle has changed and we have adopted to many new and safe ways of livelihood. From social distancing to working from home, our main aim these days is to stay safe and avoid touching unnecessary objects. This project is an attempt to make a simple touchless cordless bell, without spending a lot from your pocket.
This project demonstrates how to build a simple, touchless, and cordless doorbell using the Elegoo Uno R3 Super Starter Kit. By utilizing an ultrasonic sensor and RF modules, the system allows users to trigger a bell without physical contact, promoting hygiene and safety in a post-2020 world.
Year 2020 has taught us many new things. Our lifestyle has changed. We have adapted to many
new and safe ways of livelihood. From social distancing to working from home, our main aim
these days is to stay safe and avoid touching unnecessary objects. This project is an attempt
to make a simple, touchless, cordless bell without spending a lot from your pocket.
This video is sponsored by Elegoo Incorporation. Established in March 2015,
Elegoo is a thriving technology company dedicated to open-source hardware research and development,
production, and marketing. You can buy their products from Amazon all over the world. I'm
going to make this project using the Elegoo Uno R3 Super Starter Kit. Using the promo code from
the description below, you can get this awesome kit for a discounted price. For this project,
we need a Elegoo Uno R3, ultrasonic sensor, IR module, RF transmitter and receiver modules,
antennas, LED, 220Ω resistor, 100μF capacitor, buzzer, and a relay module.
I'm going to show you guys few different ways of making the touchless, cordless bell using the
Elegoo Uno R3 kit. First, let's put together the transmitter side using an ultrasonic sensor.
Connect the echo pin to D2, trig pin to D3, GND to GND and VCC of the ultrasonic sensor
to the 5V pin of Arduino. Then connect the data pin to D13, negative to GND,
and positive pin of the RF transmitter to 5V pin of Arduino. Finally, connect the ANT pin
to the antenna. The exact same setup can be used for an IR module. However, IR sensor may not
function properly on a hot sunny day. You may hear phantom bell rings due to hot temperature
interfering with the IR module. Plus, ultrasonic sensor has a longer range than IR sensors. So,
I'm going to use the ultrasonic sensor based setup for this project. Now, for the receiver bit,
connect the antenna to the ANT pin of the RF receiver. Then connect negative to negative,
positive to the 5V of the battery. Then you can use either one of the data pins for this project.
Place the 100uF capacitor between the data and the negative pin of the receiver.
Now we can either attach an LED, a buzzer, a homemade DIY relay module or an off-the-shelf
relay module to the negative and the data pin of the RF receiver. For this demonstration,
I'm just going to use an LED. If you want to know more about relays and how to make a DIY relay,
please check out my tutorial number 4, driving a relay with an Arduino. Link is in the description
below. Now, let's assemble all the parts as per the schematic. I really like the way I can just
plug and play everything using this kit without worrying about soldering. Start the code by
defining the variables and the pin names that will be used throughout the code. Then in the setup
section, define the pin modes. Now, in the loop section, calculate the distance in inches by
reading the values received by the autosonic sensor. If the distance is less than 20, then
transmit a signal to the RF receiver. Now, if you replace the LED with a relay module, you can turn
your wire doorbell to a wireless touchless doorbell and make your neighbors jealous for not having one.
In the final version, my plan is to add a solar charging panel to charge a 18650 battery for the
circuit. If you want to know how to create a solar charger, please check out my tutorial number 2,
DIY solar battery charger. Thanks again for watching this video. I hope it helps you. If
you want to support me, you can subscribe to my channel and watch my other videos.
Thanks. See you again in my next video. Bye now.