In this video i opena new anet A8-plus and show you how to put it together. we will go over all the steps, and show off the first prints! My review of this machine is not yet complete, but so far, other than a few gripes about the hot end, i am having a good time with this machine!
micro-swiss hot end: https://amzn.to/2pSQHsr light bar led upgrade: https://amzn.to/30UyPKm If you cant afford a donation, thats ok. leave a couple likes. and dont forget to subscribe. sharing and liking our videos is one of the best ways to help support the channel. if you can afford a donation, please contribute! a little goes a long way! thanks again for all the support people! I couldnt do it without you!
Want to send me something? Technivorous 902 n Hughes Blunt Sd 57522
now accepting reviews! sorry we DO NOT take payment for better reviews.
Hey folks, Tech Nervous here.
I have here an Anet A8 Plus and I've already cut open the box.
So let's lift it off and see what's inside.
Alright so here we have it.
Let's do this.
I opened the case from the bottom as Corianne suggested so that makes it easier to just
kind of lift off the box.
I'm going to go ahead and remove this here.
That's me walking through everywhere.
Now, if we get back in the picture here, I see the two styrofoam layers here.
We'll go ahead and show you what's going on here.
Alright so now that we've gotten the box off, let's take a look at what's inside.
There are a couple of tools in here I see.
A little screwdriver.
A pretty interesting little tool.
We'll set that aside for now.
Looks like some zip ties and a bunch of little finger condoms.
Those look like to be the size of end caps but they look like they're sticky tack so
we'll figure those out hopefully in the instructions there.
A PLA sample.
Now this is a send back unit, a return unit, so it has been used.
You can tell they tried to use this filament here.
Obviously they weren't having any luck with it.
This is the blower tube or the motor for the hot end on this beast.
That is a leveling knob.
And there's some spare parts.
Looks like there's a straight edge.
Another screwdriver, wrench, Allen wrenches.
A spring for the bed, which is missing from this corner I see.
So we're going to go ahead and put all this back in the bag so we can keep it together
because we will be needing it all.
And we will set that aside down here for now I think.
What we're going to do is remove the top layer of the bed here so we can get a look at what's
in the layer beneath.
So we'll just set that away.
Knock over a bunch of spools, this will be good.
Set that on the floor here.
And you can see the next layer.
Let's see what's going on here.
This looks like the electronics and the rest of the frame.
So, what shape is this bad boy in?
Yeah, the hot end.
You can tell this is definitely a used model.
Looks like the screws are straight.
Everything seems to be proper.
Let's get some of these components out here.
There is your cable cover.
You want those guys.
Power unit as well.
Spool holder.
Inet does give you a lot of printed parts.
This is a printed holder.
Works though, it's effective.
And mine mostly end up being printed anyway because I'll make a mod or something like that.
Loose screw.
Put that in the bag.
This is the magnetic bracket that mounts our screen here.
And keeps it vertical like that.
So that's pretty cool.
Board.
All of the cables.
All of the wiring.
Spread everything out here.
I'm gonna move this styrofoam here in a second.
We'll get a little bit better view of what's going on.
Alright, so here's the bed.
The first thing I'm gonna want to do is make sure that I have these spacers on these L-shaped brackets.
Loosened up so that little nut there, you're gonna want to back that off a little bit.
And also try to ensure that it is sitting vertically.
Because we're gonna slide the frame of the other piece onto it.
And that's pretty simple.
Everything's mostly put together.
So what we're gonna do is slide this right over.
And then bracing it up against there, we're gonna tighten these down again.
This is a pretty straightforward build.
Most of it comes mostly assembled.
Right away I'm noticing a couple of issues.
This side here is not contacting the bottom bar.
Which means that this is in the way.
So we're gonna loosen it up.
And lift the motor up just a little bit.
So we can ensure that this brace is square against here.
And then we will tighten down the bottom bracket first.
Because that's what we're trying to square.
So we'll tighten that down.
Good.
And then we will place some pressure on the motor to ensure that it is snug where it needs to be.
And retighten these bolts as well.
These might be square already but I always like to double check.
And we'll check the other side here too just to be sure.
It looks like everything is good over here.
So the next thing you're gonna want to do is go ahead and get some of these machine screws here.
Now these guys, these are the four we're looking for.
So you're gonna want to grab these out.
And they're gonna go through the bottom frame into the top frame.
And you're just gonna want to get them in there loosely at first and not tighten them down just yet.
Oops, that's not tightened down at all.
Okay, so what that was is sometimes if you don't unscrew the nut far enough
when you tighten it back down it won't turn into that V-slot and lock like you need it to.
So I'm gonna unscrew it some more.
I can see it now.
We're gonna make sure that it turns.
There it goes.
Again, making sure that it stays square.
Next thing we're gonna do is gently
and this is one of those instances where I wish the bed
when you first get it, there's zip tie clips here holding this so the bed won't slide on you.
This one, like I said, has been used so my bed will move if I don't brace it.
I need to just slowly let it down carefully here.
And I'm going to insert the machine screws we were talking about into the bottom.
And they should use the biggest Allen key that came in the package here.
See if I can dig that fat boy out. There we go.
And I want to get them started to thread just a little bit
so that I can ensure that they stay in.
But I don't want to tighten them down just yet.
Okay, actually this side I'm gonna go ahead and tighten down.
And the reason why is because they're going in very easily
which means that I am lined up with the holes properly over here.
On the right side I'm having a little bit of tension before I should
which means that I'm probably not properly lined up
so we're gonna adjust that one just a little bit.
It's not getting any resistance.
That should be good.
What about this guy?
Well, so if your screws aren't going in properly
what you need to do is loosen the bolt on the back here
of this L-bracket, on the bottom, excuse me
the one in contact with the lower part of the frame
and then as you're easing the bolt in here
adjust the bar so that the hole lines up properly.
Looks like we're good here.
So, try not to fling that bed out when I flip this guy back up.
There it goes.
Also, I should mention, you want to pay attention to
which side you're mounting these brackets on.
The motors here should be on the front of the printer
because everything else is gonna go back here.
So I have the bed clip back here, which is good
and the motor back here.
The motor for the Y-axis also plugs in on the back
which is pretty standard.
I have seen some that are reversed
but on this machine it is in the back.
And then, of course, the dual Z.
Now, one of the things you're gonna want to do
with the dual Z is wind it all the way down
as far as it can go on both sides
because that is the closest you're gonna get
to it keeping even.
Now, you can actually go in here
and unlike normal leveling
when you have the dual Z
it is preferential to
make sure that this is
not necessarily level
but true to this.
So, that's not good.
I mean, it's not absolutely necessary.
Most of your model will work out just fine
but what you're gonna want to do
is make sure this is square
and then level your bed against that
because that will help ensure that your bed is square
as well and at that 90 degrees.
So, if you do the bed first
and then this
I suppose that would work
but make sure you level the bed again
after you change this
because as you can see
on this dual Z system
if I screw just one of these up and down
I can move one side independently
and that's not a good thing.
That means you can get off balance really easily.
I mean, I can even go
opposite ways here.
It's hard to get my hands to go.
There we go.
And you can see it tilting and we don't want that.
That can cause pressures that you really don't want
on your machine.
So, the best thing to do is lower it all the way down
as far as it will go
to ensure that both sides
are as level as possible
and then from there once your end stop
is set off over here
you can make minor
adjustments to this side
in order to line it up with this side.
We'll do that a little bit later.
I don't need to necessarily do it right now
because as I'm adjusting and adding things
this is probably going to get thrown out of skew
anyway.
So, let's move on to the next step here
of throwing together this AA+.
Now, this next part
I like to do in reverse
because there's a lot of wires here
and the wiring is kind of different for each printer.
I don't have the instructions on hand
but I have put one of these together before
so I am going to go ahead and hook up my cables
and then determine where they run
before hooking them into the actual board.
So,
I have all my cables here
these are the motor cables
I have my end stop cables
cables for the actual bed
itself I'm going to just set aside
for right now because I know
that's practically a direct connection.
Alright, so basically everything that comes up
over the top here is going to
go through
this gap here
and this is including the Z end stop
and the X axis, all of that.
So, we need to pass these
through the notch
that looks like the shape of
an HDMI port
on the top
of the case.
I want to make sure that none of this is wrapped up
and just kind of get everything to go through smoothly.
So,
I just pulled a plug
hopefully I know what that is
So,
hot end
thermistor
fan
and fan. Now we are going to do a lot about
cable management in just a little bit. First we need to
get everything plugged in and get the case screwed on
and then we can pull our cables
out to the lengths that we want. As you can see
this is the
hot end
this is the bed here
and they definitely need some attention as far as
wrapping and stuff like that.
So, we are going to take care of that for sure
coming right up
here. First we need to go to the board
and plug everything in.
Now this part is pretty self explanatory
I'm going to go ahead and turn
the printer on and see if we can get a little bit
better view of the board here
I don't know if you'll be able to
see it or not but we can try
set some of this on the floor
I don't want to lose
my case screws there either
power plug
we need these guys as well
and these
are also going to get passed through
our bottom plug
there. Make sure you get
the LCD into the LCD
and the J3 into
the J3 there. So
put these over here
set that there for now
pass this under here
and also through
the lower part of
all of that
and we're going to fast forward through some of this wiring pretty quick
you can kind of see what I'm doing here
I know I'm going kind of fast for some of you
but it is pretty self explanatory
all of the clips have labels on both ends
and all of the plugs are clearly defined
on the board so all you have to do is find
the right plug that goes to the right clip and clip them in
other than
these three on the bottom here
now the three plug ins on the bottom are your
power and then your heat
to the bed and heat to
the hot end
those are also clearly marked
if you pay attention to where they're going
so fairly straight forward
I'm just going to plug these guys in here
I believe the first time actually I plugged
the thermistor into the bed
and the bed into the thermistor, yep there we go
and I had to switch them around
but that is correct
so then after that
I just started plugging everything else
so these are
pretty good, they just slide
in between those two plates, you screw down the screws
and then the last
set was actually missing the little metal
clips so I just made sure
they were properly lodged in there and that there was
no contact outside of the case so
it can't short and we are good to go
that is the plug for
the screens, pop those in up
the top right there and
just keep reading the labels
and putting things where they need to go
it does take a few minutes, now this process took me
about 45 minutes
to an hour somewhere in there
to get everything wired up properly
and then to wrap all the wiring harnesses
so I figured instead of making this a 2 hour
video we would just fast forward
through some of these parts
and here we are
so
getting pretty close to wrapping up
a lot of the plugs in here, we're going to get the last
couple in before we put on the case
as I said just make sure
you're paying attention to the labels
there's those two I was talking about that don't have the metal plates
they still went in fairly
easy, you just want to make sure they're pinched
between the two plates that are already there
and we are good to go
not looking too bad
so we're going to screw in the case, these two bolts
behind it, they go into the frame and then there's two bolts
that go into the bottom of the frame as well
and
once you get that on
you are pretty much done with the wiring
and now you need to just kind of clean it up
and take care of your wire control
so what I'm doing here is taking the
wire wrap that they had
with the package and
basically wrapping it around the
exposed wires to keep them all in a group
and kind of help with their bend
and flow, that way they're not getting in the way
or getting pinched by anything
and they're all in one place
and wire management is a big deal
you don't want loose wires all Mickey Mouse
hanging out everywhere
not only does it look bad
but it can be a hazard in several ways
so
we're going to continue watching me fast forward
through wrapping this
this does take quite a long time
this is probably the most
labor intensive part of this
then again it is something really simple to do
all you're doing is going around groups of wires
so it's easy
but kind of boring
when you're excited about getting your first print
out of the printer and you have to just
sit there and wrap wires and stare at the
thing for a long period of time
but this is
actually the second A8 plus
that I have put together
the first one was a return
unit and was not in as good a shape as
this one, this one has gone together really easily
really well, everything seems to be
pretty much perfect
and I can tell you at the time that I'm
recording the voice over for this I have gotten
some prints off of there and I am pretty impressed
so we'll be coming out with a
full review of this printer
and let you know exactly what I think
after I spend a little bit more time with it
and test out it's capacity to print some larger
models but for now
suffice it to say
I'm pretty happy with what I've seen so far
but I will show you
the results in just a second
because I have gotten some cool prints off of this thing
and I'm excited to show them off
the first things I printed
were all test prints that were
on the disk, there were a lot of test prints on here
and a couple of them kind of had me
chuckling a little bit so it was a
pretty fun experience all in all
well there you have it, the unboxing
assembly and first prints of the Anet
AA Plus, now so far I'm really enjoying this
machine, as I said earlier I will have a full
review for it later, if you've enjoyed
this video feel free to leave a like down below
and don't forget to hit that subscribe button
because we're always opening and reviewing new printers
and updating you on the latest
and greatest in 3D printing tech
also don't forget to smash that notification
button so you can get notified every time
we put up new videos, thanks guys
as always this channel was brought to you by
these fine Patreon supporters
if you'd like to support the channel on Patreon
head over to www.patreon.com
slash Technivorous
that's going to be it for this video, as always
I am Technivorous and thanks for watching
don't forget to check out our main channel page
where we do a free giveaway for our subscribers
every month, so far we've given away
things like a Capricorn PTFE tubing kit
and spools of filament
so the giveaway videos are always pinned to our main channel page
so all you have to do is subscribe
and leave a comment on the giveaway video
for the current contest
feel free to check out this video right here
YouTube picked it for my content just for you
and if you haven't already you can hit the subscribe button
right here, so what are you waiting for?
become a Technivore now
thanks again, Technivorous out