Check out my review of the creality LD-002R MSLA resin printer! this printer uses .ctb files, sliced from an .stl in chitubox, it is capable of using a ton of different resins, and is less than $300. seriously for less than the price of an ender 3 you could have 10X the resolution and a fraction of the finishing time required by fdm printing! i highly recommend you get this printer! and stay tuned, for the next #3DThursday!
Like and Subscribe! SUPPORT TECHNIVOROUS 3D Printing:
Want to send me something? Technivorous 902 n Hughes Blunt Sd 57522
Hey folks, TechNiverous here.
Welcome to the first ever episode of our new series, 3D Thursday.
Today's episode we're going to be going over the LD002R resin printer from Creality
and discussing some of the pros and cons as well as whether or not now is the right time to switch
from FDM printing over to resin. So stay tuned for all of that and more today on 3D Thursday.
This is the Creality LD-002R. Now this is a second iteration of Creality's first resin printer
and it is just under $300. I'll have links for it down below. Definitely worth checking out if
you're thinking about trying out a resin printer. Now I'm going to show you some of the models I
got off this bad boy here in a minute. You can see there's still a model hanging from the inside
there. As with most resin printers it does print in reverse so it will lift the build plate instead
of dropping the build plate or lifting the head like you see on a normal FDM machine. Now this
machine was super duper easy to set up. It comes with a USB connection so no more fiddling around
with micro SD cards. It does use Chitubox as a slicer which is a first for me. I've yet to use
it and I've started using it since I've gotten this machine and I do have some likes and dislikes
with the slicer software. I wish that Cura could do this probably only because that's what I'm
really used to. But in the end you do get what you get so I'm sure I'll get used to it eventually. I
didn't really like Cura when I started out with it either. So let's take a look at some of these
models and then I'll explain why some of them look different than some of the others. So I have two
different resins that I've tried. One is from Elegoo and one is from Shinesing. This is the
Shinesing. It is a tough resin and as you can see I was able to achieve a glossy finish on this guy
and a matte finish on this one. Now this one has been sanded down a little bit but it was matte
before I sanded it and the trick there is simply how you expose it to UV light. Now this guy
is nice and glossy because I placed it outside while it was still wet with the extra resin from
the machine. I didn't rinse it at all and that created this glossy kind of look. This one however
was rinsed in IPA and it was pretty much completely cleaned off. Still could use a little
sanding and cleanup but it left it with this nice matte finish. So on that same vein this is one of
the test models that comes with this printer. This is an amazing model. It is super intricate.
It is pre-sliced and ready to go and this is a beautiful, beautiful Eiffel Tower. Now I will say
that there was, if you look in there real closely you can see that railing going across there. There
was another one of those along the outside but during the curing process I accidentally knocked
it over and that rail had to go because it ripped off. So it did print perfectly. That was totally
my fault. This model is amazing. Everybody I show this to thinks that this is made out of glass.
The nice thing about these resin printers if you're thinking about making the switch
is it saves a ton of finishing work. There's almost no layer lines as you can see here.
See if we can get it to focus. There we go. Those lines are crisp. Those points are perfect.
You can see that this has a more transparent look here and is slightly opaque around the edges. That
is because I did sand this and complete most of the finishing. There are a couple little flaws
in there I'd still like to sand out but the accuracy of this printer is amazing and that
is further illustrated by this little guy here. Now I know this is hard to see in a figurine because
it is plastic or it is translucent but there we go. Let's get it to focus.
The detail here is amazing. Down to get it to focus again. There's a little skull right here.
You can see the teeth and the eyes on that thing. It's pretty incredible. The chest, all the hardware
in the chest, the wrinkles in his pants, everything on this is pretty much immaculate. So if you're
doing miniatures this is definitely something you want to look into. The other thing is
actual translucence. Now this is a part I'm working on. This is actually a clip
for a mirror holder. It bolts to the wall and a mirror goes in here and then it's got an M on it
for my family crest. There will be several of these holding a mirror up but you can see it's
yellowed. Clear resins tend to do that from UV light. There are ways around it but
different resins have varying degrees. Over here, let's see if we can turn a little bit.
This is a work in progress. So what this is is a sandy. So basically it's a sanding pen.
You get the sandpaper, you wrap it around the tip and slide it through the nozzle here
and there are different tips for sanding different parts and this actually works really well.
One of the things I did run into as a problem for the resin printing was that if you don't
get it out immediately and rinse it, if any of that starts to cure there, it's adding to the
thickness of your part. So if you have anything that's threaded or anything like that, it's going
to require extra sanding and sanding those threads is a little bit tricky. So if you're doing any
sort of threading or pieces that slide very very very tightly into each other, you're going to
use a little bit of horizontal expansion to make them smaller. They don't really have that setting
in ChittuBox but there are ways to make the parts slightly smaller so that they fit.
Or you're going to want to make sure that you get it out immediately when it's done and start the
rinse process. But I do like the ability that this machine and other resin printers have
to print completely translucent items. Now this item up here hasn't been exposed to any light yet
so it hasn't started to yellow at all and you can see that it is pretty much perfectly clear.
So I do need to remove this and take it off. I can show you that process right now but before I
do that I need to get some gloves on. Alright so I'm gloved up and ready to remove the model from
the build plate. I need to get a couple other things. I like to keep a rag on hand and then I
have this handy spatula that comes with the printer here and I'm going to use this to kind of
pull some of this excess resin so that it drips off of the build plate
and just kind of reduce my footprint here. Make less of a mess. It does get
a little bit messy working with these machines and if you're not careful
you can have... well you can have certain disasters and we don't want that. So before I pull this
off I want to make sure that I have a metal spatula or a putty knife because I'm not going
to want to walk around with it dripping all over the place. Basically you loosen this screw here
and then the whole bed comes off and here's my part. This one might just pop off
but you can see these rings around it that is still liquid resin oozing and if that's exposed
to UV light it will harden there. We don't necessarily want that so pop our part off.
Let's put this back for now. One of the other caveats with this machine is you're going to
want to make sure that you put the lid back on too because you don't want that resin hardening
in the vat. It can happen. And here is our part. Now this is the part of the process where I will
get some IPA and I will rinse it but first I need to remove what little support has clung to the top
here. So I've got a pair of clippers here. I'm just going to kind of shave it carefully.
This was printed with no support. Printed really well. I'm pretty happy with it. I'm
going to have to work on the orientation because I don't want this sort of marring on the actual
dome. Now this is a prototype so I'm not worried if the size of this isn't exactly accurate.
I'm going to actually fill this with something and then try to seal it with more UV resin
but I wanted to see if this process would work. So I'm going to come back to this part here in
just a minute and show you it after it's a little bit more cleaned up. Let's go over some of the
machine. Today we are taking a look at the Creality LD-002R. So since we're talking specs
obviously everybody's going to want to know right off the bat what is the build volume. We're
looking at a solid 120 by 65 by 165 millimeters. Now that may not seem overly large but it is big
enough for most things and in fact you can fit about five or six good sized miniatures on here
without any problems. More if you orient them properly. The layer height on this guy can go
down as low as 20 microns. Recommended layer heights between 20 and 50 microns which is
pretty slim guys. That leads to a super high resolution. The resolution on this guy is 2560
by 1600 and it is super duper accurate on the x y axis. So the z-axis the positioning is pretty
much spot on. It's led by a linear z-rod and the printing seed is about 50 to 70 millimeters
per height divided by hour. So there's a little formula there but I can tell you
the big advantage of printing with a machine like this is it doesn't print by
connecting points. It prints by dividing a model into different two-dimensional pictures. So it's
doing the whole picture with a single exposure which can take anywhere from a couple seconds to
a minute depending on what material you're using. But still to finish a whole layer on a model in
a few seconds is pretty incredible and this leads to some pretty quick printing speeds compared to
FDM printing. The bed leveling on it is manual. There are four bolts connected to the neck of
the main positioning hanger here and with these guys what you'll do is loosen them up home the
thing down to the bed and get it flat and then you'll tighten them up and then you know that
it's flat. It's a lot easier to level this machine than it is to level an FDM machine.
So again major perks with this machine. Now it is technically an MSLA or LCD machine.
It does use most standard resins and basically what the LCD means is that it's not a laser in
there tracing a path it's flashing an image. So you do use STL files with ChiduBox. It just slices
them in a different manner and it'll slice them into layers like a regular slicer but then instead
of slicing a path out of that layer it makes a 2D picture of the whole layer and it's pretty
incredible. You can actually see it on the screen what light image it's beaming into the plate at
that time which is pretty cool as well. So it does support third-party materials and it has a 3.5 inch
touchscreen display and we'll get to the display in just a second because I did want to touch on
that. It's really beautiful and there are a lot of good operations in there. First it does run
on ChiduBox and when ChiduBox puts out a file it puts out a CTB file. Now these files are a little
bit longer to write than a standard STL because it's technically not binary but it all goes right
onto a USB stick and the USB stick pops right in so no more flopping around with micro drives or
SD card adapters or anything like that. I am sure I'm not the only one with a bevy of these little
guys just laying around easy access. So as far as the size of the actual machine and its weight
itself the frame dimensions are 221 by 221 by 403. So basically the base of it would just barely fit
on the build plate of an Ender 3 and the top of it would extend past it by about 170 millimeters. So
a little bit slimmer and a little bit thinner than the Ender 3 so pretty compact design
and pretty elegant as well. As promised as that prototype a little further developed it looks
like it's going to work for what I want to use it for. Leave me a comment down below if you think
you know what this is going to be and hit a thumbs up if you have no idea. And before we wrap this
up I wanted to show you guys a couple of the best prints I've gotten off of not only this machine
but any machine all together and that is because like I said the amazing ability to hide a seam
with this printer as well as the lack of finishing to remove layer lines. So let's start with
Voldemort here. Now this is Voldemort's wand obviously too big to print in one piece on this
printer. It went together really really well and looks pretty seamless. I'm very very proud of this
piece it's one of the nicer pieces that I've done and even though it's super simple it is definitely
making me lean towards getting a lot more of these machines. Obviously I'm going to need some larger
ones but for the time being this is definitely the handiest machine in my print shop. So this
is the elder wand. Now this one I took a little bit different route on the paint job. This was
actually printed in that skin colored tough resin from shine sing and it went together pretty
seamlessly as well. I really really like the detail on this one as well as the way the paint job came
out. So all in all I'm very very happy with the production quality of this printer. You really
cannot beat it for the price not to mention the fact that it is a Creality machine and that says
a lot in the 3d printing space. One of my first printers was a Creality machine was the Ender 3
and I still have it in fact excuse the mess it's over there under repairs or upgrades I should say
we're putting a second extruder on it and I did finally receive the board for that so you will
see that in an upcoming episode of 3d thursday but for now that's going to be it I definitely
recommend checking this printer out as I said there's a link below they are affiliate links but
we got to do what we can to keep the channel going if you guys enjoyed 3d thursday don't
forget to tune in next week for another episode not sure what the topic will be but if you follow
us on twitter or instagram we'll be sure to let you know a day or two ahead of time so you can
decide if you want to tune in but definitely hit that subscribe button and the notification bell
that way you get notified every time that 3d thursday posts a new topic so as I said this
should be a continuing series going forward thursdays at 10 30 a.m central time and we look
forward to seeing you on the next 3d thursday well that's it guys that's going to wrap up this video
if you've noticed the shirt the merch is available go ahead and check out the teespring merch link
down below it won't be available on a channel store until I reach 10 000 subscribers and so
far I am just about to hit five thousand so it'll be a little while couple more months before you
see this on the actual channel but they are available now I have a couple other designs
feel free to pop over there and check them out and know that any purchase through the teespring site
definitely helps to promote our site here and increase the channel's ability to make videos
in the future so we appreciate all your support don't forget to check out the teespring link check
out our patreon link leave a like on this video and hit that subscribe button because we have a
lot more coming at you in the coming days