Check out this cura video on seam placement for round objects. you will find with #3dprinting most settings are adjusted on a case by case basis depending on needs, and round objects have no corner to hide a seam in, so lets go over some tactics!
Like and Subscribe!
Send me a gwei! (ether address, all donations accepted!) 0x95F4EaB8A738F4F27e7c04aEe1E10C8E666C2D0c send me a satoshi! (bitcoin address, all donations accepted!) 31zvj8ybxVVTLw6nPvAHYqu3qDVhC1sRqk
Want to send me something? Technivorous 902 n Hughes Blunt Sd 57522
AI Generated·May contain errors
Hey folks, TechDiverius here. Today we are back with another one of your Kira questions. This
question comes from Terry Jones and it says, what would be a good setting for seams with
rounded items? So we're gonna go ahead, we'll give him a little heart and a like right there.
I will respond with a link to this video to you, Terry. Let's jump over to Kira and I happen to
have a round object. So let's drag this guy in here. All right, now we'll slice and check our
seam settings. Now, ideally we would be placing our seam on the inside because that would make
it less visible from the outside. Now, since this is a cup shaped model, the inside is still going
to be visible when looking down into the model, but there are ways to place the seam on the inside
of the model so it's not visible at all. Although it can be a little tricky depending on your model's
geometry. First, we're going to take a look here. I'm going to increase this because it'll
go a little bit quicker here. And let's scroll down and find,
don't have the seam setting showing. So let's see, it's in walls,
z-seam alignment, z-seam position, x and y we're not going to use. That's for manually
placing the z-seam. It can be helpful, but not necessarily easy to do.
So we can check that so it's available. We probably won't be using it though,
so we'll close this now. You can see it's got a set position for that.
It's basically just an offset from where it's going to start its code, so that's not necessarily
needed. Smart hiding is what we have selected, and this is my usual selection because it will
try as it says. Control whether the corners on the model outline influence the position of the
seam. None means you have no influence. Exposed seam means it seems more likely to occur on an
outside corner. Hide or expose means the seam is likely to occur at an inside or outside corner.
So there are no corners on this model, and that's the main question. So in some cases,
and that's why I'll slice a couple different times here, in some cases you can get the
z-seam to go to the inside of the model, which would be preferable. If however that does not
work, we are going to randomize the z-seam, and Kira has this handy new visualization they added
in one of the latest versions that you can actually see the z-seam. And here it is pretty
well split between the inside and the outside. It's not a contiguous seam, but it is going to be very,
very visible as a line running through our model. Now depending on how much post-processing we want
to do, this could be ideal because if we just want to have to sand down that one spot, it could
work. However if our layers are as thick as this, odds are if we sand that down it'll be way smoother
than the rest of the model. So these are things to take into consideration as well when placing
your seam. But let's go ahead and set the z-seam to random, and we'll slice again. And we'll see
if we can break those little white blobs up small enough, in the long run they'll end up looking
like tiny zits on the model, but that can be beneficial to the post-processing process too,
depending on how you're planning on doing that. And there are several other ways to do this. It's
going to take a minute to slice here, so I'm just going to let it go through its motions. While it
does that, we can take a look at another question here by Dapper Dan. So he's saying, hey by chance
of you seeing this, I'm trying to... All right and here we have it. Let's jump back over to preview
mode. You'll see that the seam is very well dispersed throughout the model. Now depending
on your retraction settings and how well they're tuned, this could also be the best way to disperse
that seam throughout a round object. Because if that retraction is on point, you shouldn't notice
any blobbing or zitting at the seam anyway. So you could end up with a very very fine model.
Now does this mean that this is the best setting for a z-seam on a round object?
Obviously not. The biggest thing to consider here is the end use of the item. Now this particular
item is a basically a spacer that goes between the floor and the middle part of the bottom of
a table. So it's never going to be seen. I wouldn't be concerned with the z-seam. However, obviously
it is something that is troubling you. So I recommend testing out all of the settings to
be honest, and seeing which one works best for your needs. However, as I said, I would start
with random or user specified and smart hiding. Now you can change this to a simply hide the seam,
and let's try this one time and see if it gives us any better results. Like I said,
if we can get more of that seam on the interior of the model, that means it's doing a better job
of hiding it. And it doesn't necessarily mean that it's the best setting either. Like I said,
it's more of a use case scenario where it depends on what you're doing with the object, and where
exactly you want to hide the seam. Even if the round object has one hard corner on it, in most
cases it is your best bet to hide the seam on that outside corner. Just because the corner is sharp
anyway, and you can't really see it. However, if the object is completely round, that's not a
possibility such in this case. So again, we are letting it slice, and I will be right back with
the results. Actually, let's just stick around. It looks like it's going pretty quick. We're going
to be getting a preview here in just a second. So while I wait, I'll remind you again, don't forget
to subscribe guys. I know you guys hate hearing that. It gets annoying, whatever. I need your help.
You subscribing, leaving likes on these videos helps other people find these videos, which helps
me make money in order to make more of these videos. So I can't do this without you guys.
Make sure you subscribe, hit that like button, and I really appreciate it.
We're almost done slicing here, and I'm curious to see what the end result is. I generally have
better luck with smart hiding than with hide seams, so I don't use it too often. But in this case,
I think it's a...