In this episode of Fusion 360 for #3dprinting , we are taking a look at how to use the revolve extrude method, and the sweep method, to make two different styles of vase model to 3d print! if you have any fusion questions leave them in the comments!
Send me a gwei! (ether address, all donations accepted!) 0x95F4EaB8A738F4F27e7c04aEe1E10C8E666C2D0c send me a satoshi! (bitcoin address, all donations accepted!) 31zvj8ybxVVTLw6nPvAHYqu3qDVhC1sRqk
Want to send me something? Technivorous 902 n Hughes Blunt Sd 57522
Alright folks, TechNibbers here. Today we are looking at Fusion 360. We're going to do a couple
different techniques to create some faces. So the first thing I'm going to do is start a new design
and we're going to use a couple different techniques to do this. The first one we'll
use is going to be the sweep. So what you need to do is select this create sketch button right
here and then go ahead and select either of the two vertical planes. It doesn't matter which one
because we're going right in the center here. So basically we're going to start a line
at the bottom here and extend it upward about 100 millimeters. Again the height doesn't have
to be precise. We're going to be able to change that model scale later in our slicer so we just
want to get the design right right now. So once you have that vertical line go ahead and click
finish sketch down here in the corner and we're going to go back and we're going to
click create sketch again and this time we're going to select the bottom. Okay so
what we need is some sort of shape for the outline of our base. Let's do this. Let's take
circle here and we'll make a cute little heart shape. How about that?
All right so you can do any shape you want for the profile. Now we are pretty much ready to begin.
What we're going to do is select a couple of these faces and in our case we'll just select
the whole shape here. Now this heart you'll notice is off-center so we should get a funky return out
of this. Let's go ahead and click create and sweep. We're going to sweep not extrude. So
we have our profile selected. Let's select our path. Apparently it thinks we have our path selected.
There's our path and there you have it a heart-shaped extrusion. But the reason we're
using sweep and not extrude is because we wanted to add a little twist to it. So if we put in a turn
we can get variation in degrees here and with that done. Actually let's see how I wonder
if we tested the limits of this or what it does the further up you go. So that's pretty cool.
I think I would try to print that in vase mode. Okay so to the next step we're going to do is
click the top face here and click shell and then just go to about two millimeters if it'll let us.
Hit enter and there we have it. That is our first vase mode vase. We'll try that out in just a
minute. The next thing we're going to do is we're going to do this using the revolve extrude method.
So let's go to new design again and create sketch and you're kind of going to want to do the same
thing except this time we're going to do it all in the side plane. So no matter which one you pick
whatever plane you want to choose as long as it's not the bottom what we're going to do is we're
going to grab a line here and this time we're going to extend it through the bottom of where
our piece is going to be to about 120. And go ahead and just hit that there. The next thing
we want to do is go ahead and create our vase. So we wanted to have a flat bottom
and there we go. And this is basically just going to create the profile of our item here.
It could look like a vase. That'll be fine. Close that up. Then we're going to go to revolve.
Move this over here. I have the profile selected. It's this one. Let's just go back and
reselect. So right there and then the axis we're going to select this tall line here.
And there you go. Alright so we have our vase except we have a little problem here. Let's go
back and edit sketch. We want to make sure this top line here is flat because we want it to be
a face. We want to be able to select it. So we'll use a straight line for that. Now let's try this
again. Revolve. Axis. Right there. There we go. Now we can select this face and try to shell
two millimeters. There you go. There you have it. So two ways to make a vase in Fusion 360.
We're going to throw these onto the printer and check them out in vase mode and we'll see what
happens. So let's jump to Cura real quick and slice them up. Here we are with our two finished
vases. As you can see both of them came out pretty nice. You can still see the heart shape
in the top of this one and it did get a nice little twist to it. So vase mode worked very
well on this. This was the one that we did with the sweep and the rotate worked really really
well. This was the revolve extrude. This little amphora type vessel and it came out pretty well
also. So you saw the footage of the time lapses of these. The first one was really really shaky.
That's because in between the two I also made this piece here with Fusion 360 and the second
one was a lot more stable and in the same spot but there is a little bit of wobble here. So
we'll work on taking that out. But very very happy with the results of these two vases
and stick around if you want to learn more Fusion 360 tricks. If you have any questions
leave them down below. We're always doing videos for 3d printing whether it's Cura questions,
Fusion 360 or anything like that. So go ahead leave a like on this video and hit that subscribe
button guys. Don't forget to leave me your questions and comments down below and we'll
see in the next one. Tegnivorous out. Stick around guys I got another YouTube recommended video for
you right here and if you haven't already subscribe, subscribe, subscribe. Make sure
that you smash that like button. We'll see you in the next one. Tegnivorous out.