My Garage Can Detect My Car! RATGDO Disco

Smart Home Devices
120 followers
1 Video View·Aug 19, 2026
Reed's Smart Home walks through the firmware setup and installation process for adding a sensor-equipped garage controller to Home Assistant. The project demonstrates how to configure the device to detect vehicle presence, enabling advanced smart home automation possibilities for a garage.
AI Generated·May contain errors
I'm about to make my dumb garage door smart using RAT GDO but this isn't just any RAT GDO.
This is the disco version so it can tell if a car is parked in the garage or not
but it has to be mounted a specific way on the garage door opener which might be kind of
challenging. I installed RAT GDO on this middle garage door opener and it went really well but
it's not the disco version so I could mount it however I wanted and I didn't install RAT GDO
on the third garage door opener. I used another option and I'll explain why at the end of the
video. All right let's go set up this disco version. To set up RAT GDO I need to install
the firmware which is really easy to do. It's on their website and I'll show you how to do that
but first I have to know what kind of flavor of evil corp that I'm using. So if I have a little
yellow learn button that's security plus 2.0 and if I have a red purple or orange learn button
that is security plus 1.0. So you'll need to know which one you're using because there are two
different types of firmware depending on what kind of garage door opener you have. So this page is
where you install the firmware. I know I have a yellow learn button so I'm going to choose security
plus 2.0 and then I'm using the RAT GDO disco and I'm not using the encoder. When you're adding the
firmware make sure you're using a good usb-c cable that can transfer data not just power and connect
it to your computer not to a usb hub because it can give you some issues. So yeah pretty easy
and then you enter your wi-fi credentials so it can connect to the network.
There we go it's connected let's connect this to home assistant. All right there we go I installed
the firmware connected it to home assistant and see that that was pretty easy. Now I have to wire
it up to the garage door controller and mount it. Now this is going to be a little more challenging
because it's summertime here in Arizona and our garage is like a big oven so yeah I'm going to be
sweating a lot. To install the RAT GDO it's a lot easier than it was a few years ago. Now it comes
with some wires this just plugs right into the RAT GDO and then these wires plug into the garage door
opener and then to plug it in for power you use the usb-c port on the bottom it comes with a usb-c
cable and a charging brick so that's nice and there's usually an outlet right above the opener
so let's do that and then we'll worry about mounting after. All right I got the RAT GDO installed it
wasn't too bad as you can see I have the wires plugged into the little connector and then those
three wires plug into the garage door controller and then the usb-c cable plugs into the little
power brick into the outlet. So yeah it took a couple of minutes it's kind of a pain to fit the
wires into the garage door opener but wasn't too bad. As you can see I have it connected and I can
control it using RAT GDO. It's working I have it pulled up in home assistant now I need to mount
the RAT GDO disco pointing straight down so it can see if a car is parked here or not and on the
website it says to use these brackets just kind of clip it onto that but the light in the garage
door opener right here kind of sticks out and doesn't have a clear line of sight at least I
don't think it will so I might have to mount it right underneath. I am burning up out here but I
got it mounted I ended up putting it right underneath it and just used some velcro strap so
I know a little janky but I think it will work. I haven't tested out with the car yet but I'm going
to do that in a second. I also removed the light bulb in there that way I could run the wires
on this side and just kind of mount it so that way they don't get too hot or anything. The only
thing I'm really worried about is this yellow wire right there that is the antenna for the RF signal
for the button like in a car. When I've used RAT GDO it definitely decreases the signal with the
button a little bit but being this close hopefully it's not too much I can still open up the door in
the car so let's test both of them out. All right first test let's see if the button in the car can
open and close the garage door and it does so that's good to see I'm pretty far away so that's
good enough for me. Next let's test if it can detect the car parked in the garage. Right now
it says it's clear because we're parked in the driveway. Well that was disappointing I pull up
and it doesn't detect the car it does change the distance in millimeters though so it is seeing
something so I checked online and apparently you have to enter in the value in the little sensor
configuration number so it will tell you how far it is like mine said it was about 877 millimeters
away like when the car is pulled in you're supposed to add about 20 millimeters to that
I entered that in the configuration then it detected the car that was a little annoying
that the instructions didn't tell me to do that. Awesome I'm glad it's working so well and I can't
wait to use this sensor if the car is in the garage or not with automations. One of the automations
that comes to mind is one I've shown before like if the garage door is left open notify me well
that's usually set to like five or ten minutes that it's left open because I don't want to be
notified right away if we're unloading groceries and yeah that's just going to be annoying well
what if we're leaving on a trip and we pull out of the garage I want to be notified immediately
if there's no car here and the garage door is left open for like 30 seconds so I can do that
with this sensor because it can tell if a car is in the garage or not so yeah there's gonna be a
lot of cool automations I'll be able to do. Like I mentioned at the beginning of the video I'm not
using RAT GDO here on the third garage door controller because it's using security plus 1.0
the purple learn button so it's different than the other two where I'm using RAT GDO technically I
could use RAT GDO here it depends on the button on the wall if it's compatible or not and if it's not
you need an extra accessory for RAT GDO to get it to know if the garage door is open or closed
I didn't really want to mess with all of that I already had a Maros garage door controller so I
just plugged that in and it works extremely well with these older garage door controllers because
the wires just go right into it it can open or close it and then there's a wire that goes all
the way to the door there's a little sensor that I screwed in and it can tell if the door is open
or closed so very basic and since we're just parking bikes here I don't need to know if a
car is parked here in the garage so yeah if you have one of these older garage doors then maybe
you'd want the RAT GDO DISCO to tell if the car is parked here but this one works perfectly fine
so that about does it if you guys have any questions about the RAT GDO DISCO
let me know down in the comments and thanks for watching
