Practical Trimming Tips and Design Advice for Unified Wheel Thrown Forms ¦ PAUL DONNELLY.

History culture hero
16 followers
4 Video Views·Aug 12, 2026
AI Generated·May contain errors
Several different ways people use to center or recenter a pot after it's been thrown and they're
moving on to the the trimming stage. You can use a pin tool right here just to sort of hold along
the side and as it you know strikes the pin tool it's obviously closer to that side. Or you can
you know do it to the you know some people do it on top and they'll look and see which side is wider
and which side is more narrow. So I mean really my goal here is just to center the bottom bottom
third of the form really. And you know it's never perfectly or truly centered so you just want to
try to find some sort of happy medium. Oftentimes when I try to center the top it's you know the
bottom's off and vice versa. And I'm just going to take some clay here. I'm going to hold the pot
down and push this along the side. Now I have a tendency to put clay around the whole bottom and
then just sort of affix it to the wheel hub by running my finger. But you can just use a couple
wads. People prefer different things. So when I trim I start off with the smallest tool possible.
A loop tool. And what this does is it just cuts through the material real quick. I like trimming
with a very very very high wheel speed. And really what I'll do is I'll just get my hands on the pot
and you know really choke up on my tools. Almost as if you know I'm holding them right at the end.
And you know two hands so I have my hand on the top and then my hand on the side and I touch
them together and I'll start right at the foot. The reason why I use a smaller tool to begin with
is because it just sort of cuts through all of the unevenness of the pot. If I use something that is
wider such as this tool here it'll tend to sort of just move back and forth and sort of follow
the inconsistencies. And really I'm just moving very very very very slow up and down the form.
When I'm trimming the first thing that I'm going to do is I'm going to figure out the diameter of
the foot that I want. You know and really a lot of this comes through exploring and trying
different things and playing with the relationship of the proportion of the foot and with the rim.
So in order to figure out the diameter I may have to lean over and kind of look at the profile of
this pot and get an idea of the rim. I like using about a half leaving about a half inch from the
interior of the foot to the bottom of the pot. And what that does is it allows me to play with
the height of the foot. And so I can always take the foot down or take a little bit off if it seems
too tall but I can't add clay. So I like leaving that extra clay down in the bottom of the of the
pot. So once I've decided the diameter of the foot then I can come and figure out the height.
And I'll just take this same tool and come down and then into the form into the bottom of the
form. And I can switch tools now. I can kind of move to a a bigger tool and even a larger one.
And the nice thing about this larger tool is that it'll it'll allow you to make big sweeping angles.
And then what I'm going to do is I'm going to I'm going to basically trim this here so it has
just a little bit of an undercut. That's just an aesthetic purpose. Sometimes it also acts to help
stop the flow of glaze. Now I can go into the interior of the foot and I'm just going to start
right here. I'm going to leave it a little thicker than I I need to in case you know this this jabs
or cuts. And so what's really subtle is you know this is a lot like centering where my tools are
moving back and forth on my hand like this while I'm trimming. And I'm just you know applying
pressure on and off. So I'm actually sweeping the trim tool from side to side going from
the exterior into the interior and back out. And I'm going to angle my foot. So
and I'm going to come back with my rib and I'm going to trim and shape and form. And so this
is taking just a little bit of clay off here and it's giving me just a really beautiful sort of
contour in the interior of the cup. And again you know you have all these different sizes
here so you can get you know different angles. Which you know it's harder to get that with a
exact curve. And I can come into the bottom here and just sort of trim out a notch like that. And
just adds a little extra dimension on the on the bottom part of the cup. So in thinking about
design you know what I what I really look for is sort of similarities throughout the object. So
in other words where I have a kind of a rounded foot in here it matches sort of the round interior
in here. There's attributes that sort of match up on the form and that's what can kind of you know
that's what will bring unity to the piece. So the final thing that I'm going to do I'm not going to
I'm not going to use a lot of clay. I'm just going to get a little bit of water on the wheel head
and just kind of wet this down and move this. And as you can see this is like a little bit
wobbly here. So we're just going to try to find a happy medium. And I'm just going to trim the
exterior of the form real quick just to kind of give it a little bit more just a little more
proportion. I'm going to trim a thick rim into it. So probably the thing to do is to break this up
into thirds. I'm just going to score a line on here with my pinky. So you know if I break this
top part into thirds as I was talking about earlier my trimming tool just very gently come in
and down to the bottom. It can just be very subtle. And that little water that's on there
is just enough to keep it adhered to the wheel. I'm not going super fast in the same way that
I was when I was trimming the foot. Just very gentle. So you know what we end up with is a
piece that is very curvaceous on the interior. You have a double volume but then on the exterior
you have something that's very angular. And you know that's like one of the really beautiful
things about throwing that you can have that. One of the one of the neat things about when I
was in China is that you know there they just rough the form out. They throw everything really
thick and wobbly. And then they come back and they trim all of the detail into the pot. And
they actually make the shape of the pot just by trimming solely. So it's a kind of playing with
that idea a little bit.
