The creator builds a custom terrarium featuring a dynamic, automated weather system. By constructing a bespoke glass enclosure and integrating a rain-simulating drip plate and a mist maker, the project transforms a static plant box into a living ecosystem with programmed cycles of rain, fog, and shifting light to mimic real-world weather patterns.
At first glance, this tiny jungle in a box may appear like any other terrarium,
but there's more than meets the eye. Terrariums regulate themselves through
processes like evaporation and condensation. While these weather-like patterns are interesting,
I was curious if I could make a terrarium with a dynamic, built-in weather system,
featuring rain and more. I've made many experimental terrariums over the years,
including one that rained, so I already had some experience with this concept. However,
that one was a prototype with a constant downpour of rain, the opposite of what I have in mind for
this one. To work as intended, my container selection had to be on point. I had hoped to
use this old nano aquarium to save time. It looked promising, until I saw how much space the pump
would occupy. I didn't have anything else that could work, so like usual, my best option was
to build something from scratch. Luckily, I had a few unused aquarium lids that were perfect for
the job. As I said, this tank lacked room for equipment, but it also needed more room for the
rainfall effect. With those in mind, the lids weren't too far off from what I needed, so I only
had to make a few cuts. The steps for that were the same as usual. Measure and mark the glass,
align a guide, score a line, and snap them to size. That was until I got to this narrow section.
I used a tool's wedge to separate it. Afterward, I sanded the sharp edges, rinsed debris,
and used isopropyl alcohol to remove oil. I added anchoring tape as well. Typically, this is when
I'd tape the inside, but I decided to take a different approach with the seams. I applied
silicone along the bottom and edges like usual. However, just as I was about to assemble it,
I realized I made an error. The bottom was too small. I immediately ran to the shop to make a
replacement, because I did not want to redo the silicone. Mistakes are nothing out of the
ordinary. What I adjusted was how I finished the seams. Instead of smoothing them, I removed
them entirely with a razor. This terrarium would have low structural demands, so they really
weren't needed. I did most of that before it cured, though I had to clean it up the following day.
Tone was just crawling around the animal room and he wanted to see how this turned out.
I think it turned out pretty well. I'm not sure what he thinks, but we're just gonna have to
move forward with the project. I'm glad I went the custom route, even though I was avoiding it at
first. The extra space and height were well worth the effort. The challenge I faced now was creating
a drip plate for the rain. I knew which light I wanted to use, but I didn't want to block it with
a plate. To stop that from happening, I either had to shape the plate like a U around the light,
or use something transparent. I chose the latter, specifically corrugated polycarbonate.
It's easy to work with, and I thought the voids within it could help spread the water as they
fill. The only caveat is that cutting parallel to them leaves ridges behind. I usually shave
them off. Conversely, cutting perpendicular can be done with a simple score and snap.
To avoid making a bunch of seams, I cut through a single layer of the material to create a little
tray. That was great for the sides, but inevitably, I had to cut strips for the front and back.
I decided to assemble them with waterproof seam tape. After cutting it into strips,
I secured the outside corners for stability, followed by the internal seams to waterproof
the edges. I covered this with tape to mark a boundary. Then drilling from the center out,
I created a rough staggered pattern. Certainly not the best looking solution, but it didn't
need to be. That wouldn't matter either way if it didn't work, so I gave it a test run.
It did its job well enough that I felt confident proceeding. Plus, with a bit of extra tape around
the outside, it fit snugly in the top without obstructing the light. The other major component
for this to function as intended was a divider, which I made from expanded PVC board. Cutting
it down was a breeze, and even with the hardware, the display was a decent size. I just had to
account for spacers, a water pass through, and a vent. These new openings were essential,
but they needed barriers. I covered the vent with coarse screen and the pass through with fine screen,
sandwiching them between smaller boards with super glue. Then I secured the spacers. These
ensured the distance from the back remained consistent and doubled as mounting points for
tape. At this point, it was nearly ready to go. I just had to modify the pump because I wanted it
to feed through an airline. To make that work, I had to reduce the opening with a different tube.
In place, I lined it with the tray to mark for and create an opening. I added a valve to control
the flow as well. That meant it was ready for water. I got all the components roughed in and
it's time to give it a test run. The only issue that I foresee is water potentially leaking over
the tray here. Otherwise, it should work. Let's see what happens. My guy's back there watching
to see what happens. Initially, there was hardly any flow, and even after adjusting the valve,
it still wasn't doing much. I thought it may have had something to do with the holes,
but it was actually the valve. So I replaced it with a splitter, which made a huge difference.
The light remained unaffected too, which was a bonus. Remember that vent from earlier? Well,
I included it for a different feature. A mist maker. It seemed like the appropriate post-rain
occurrence, don't you think? Just ignore the rave happening in the back. I'll hide that later.
In the meantime, the environment could finally take shape, beginning with the false bottom.
I filled most of it with coarse metallomat to keep open space for water. You'll see that I
left the edges exposed to refine the appearance from the outside with vine filter sponge.
However, if I were to do this over, I would have just used metallomat. Anyway, I topped
it with a carbon filter pad, and it was ready for life. I didn't want water splashing all over the
glass, so I felt the scape had to be simple, consisting of just a few wood chunks. Using
their flat faces allowed me to lay the foundation effortlessly, even though it might not look like
much now. However, I wanted them to be more flat, so I took them to the belt sander.
That revealed some pretty amazing wood grain on this one. Next, I rehydrated some sphagnum moss.
I lined the bottom with it to mitigate particles from entering the edges of the false bottom,
and to stabilize the wood. That said, the background itself would lock these in place.
I made that using aqua soil and natural clay cat litter, which is bentonite clay. I gradually
added water, kneading them together until uniform in a roughly 3 to 2 volume ratio.
Smearing this onto the wood acted like an adhesive, effortlessly holding them in place.
I feathered the clay off of these, and ultimately covered all of the PVC with it.
This natural option is relatively easy to do, but is best reserved for wet setups.
It tends to dry and peel off under suboptimal conditions, though it can always be rehydrated
and reused. Any excess can be wiped or scraped away. To create a sloped landscape, I decided
to pull some sphagnum moss from the front. That's where I deviated from protocol and used aqua soil
instead of terrarium substrate. I knew most of this would likely be saturated, and I felt that
aqua soil would hold up better under those conditions. Another benefit to these clay
backgrounds is that they're great for growing moss. I had an assortment of species, and by that,
I mean I couldn't tell you exactly what they are. What I do know is that they grow well in terrariums.
It came together quickly, especially with the addition of maple roots. They helped bring more
interest, but I knew that plants like this beautiful fotonia would take it to the next level.
I situated patches of it on the sides of the scape to soften the edges of the wood.
Since these are so strongly variegated, I filled the rest with green plants like margravia
and anubias. I figured it could benefit from sphagnum moss too. That's when I noticed something
odd in the propagation bin, this silly mushroom. I've never seen one quite like it before,
so I figured I'd share. Anyway, the brighter green in the moss contrasted nicely with the
other plants. I filled the remainder of the foreground with the other mosses, more anubias,
and oak leaf creeping fig. Most terrariums are incomplete without springtails, which help keep
the environment free of mold. After a quick spray, I cleaned the glass, and like that,
the interior was done. That brought me out to the exterior, which I wanted to appear sleek
and intentional. Typically I'd do something like this out of wood, and maybe I'll do that later
with this one, but for now I used PVC board. I cut it down into strips which I glued together,
before adding a lip along the side. This sat perfectly on the box, hiding all of the rain
equipment in the process. Before I could leave it there for good, I had to create holes for the
Repeating those steps, I created a frame for the bottom. I also made side coverings,
however I had to remove a section on the right side to secure the light's bracket with mounting
tape. Then I completed the lid with mitered pieces and ventilation holes. Typically I
wouldn't add them for something like this, but I did here because of the moisture levels.
Finally, I added a piece of thin plexiglass under the lip. That completed the build itself.
All I had to do then was program the features. The light has a fully adjustable and timeable
WRGB spectrum that I was able to ramp in and out of the rain feature. Meanwhile,
the pump and mister run off of smart outlets around that. Here's my schedule for reference.
Altogether, that resulted in a terrarium with its own weather system. At any given time,
the lights look like this. However, as the storm rolls through, they become subdued in blue until
the rain falls. Slowly, the lights return to normal until the rain stops and the mist rolls
in. That happens automatically over about the span of an hour, but I programmed a sped up version so
you can view the cycle in its entirety. All of that culminates in a terrarium that I think is
pretty interesting and unique. I had a lot of fun creating it, but it's not the first time I've made
an experimental terrarium. If you enjoyed this, you'll also like the time I made a set of modular
moss cubes and when I made a terrarium to filter a nano fish tank. As always, thank you so much for
watching, and until next time SerpaSquad, take care and peace.