My Latest Smart Home Projects (wins & fails)

Smart Home Devices
120 followers
7 Video Views·Jun 28, 2026
I've been doing lots of smart home projects lately, including cutting through drywall for low volt wiring and mounting COB light strips. But I learned some lessons the hard way. 😬
AI Generated·May contain errors
Video Summary
AI GeneratedThe speaker details two smart home projects: installing a ceiling-mounted wireless access point and setting up custom COB LED light strips. While the network installation was successful due to careful planning, the lighting project became a frustrating ordeal because the speaker rushed into soldering, only to discover that the kit already included easy-to-use solderless connectors.
I did two smart home projects recently, adding some light strips here in the shop,
and I mounted a wireless access point on the ceiling. One of those turned out to be a massive
headache, and it's not the one that I would have guessed. It's my fault and it's kind of
embarrassing. Let's start with the first project, mounting the wireless access point on the ceiling
because having it sit on the shelf, uh yeah, that can't go on forever. It's a pretty straightforward
project. Run the ethernet through the ceiling into the attic and then down the wall and into
the switch. And it's PoE, it's low voltage, so pretty simple. But before you start drilling holes
into the wall, you want to make sure you know what's on the other side because you could hit
an electrical line or even worse in the attic, a water line. Yeah, water lines are in the attic, so
got to be careful because you could cause some serious damage to your house. For the wall, I
used this camera, and I love this thing because you can move the camera all around, there's a
light, you can easily see what's on the other side of the wall. I saw that there was some cables,
so I knew to avoid those, and if I cut in the spot I was planning on, it wouldn't cause any problems.
For the ceiling, I didn't want to rely just on the camera, so I went up into the attic to find
a good spot, and I did find one that didn't have any wires or water lines. I took a picture of it
to know exactly where it is in reference to the ceiling lights and vent, and that way when I was
down on the ground, I knew exactly where to cut. To cut a hole in the drywall and add one of these
low voltage boxes is very easy to do. I was kind of scared to do it at first, but it's pretty simple.
You just line one of these up with a level and put it exactly where you want it. You mark each
little corner, there's a little hole in each corner with a pencil, and then you trace a line from each
dot, and that way you know where to cut with a drywall saw. And yeah, pretty easy to do. After I
cut a hole in the drywall on the wall and the ceiling, I fed some Cat6 up into the ceiling,
went up into the attic, and then I drilled a hole into the fire block. That way I could feed the
cable down through the wall. There was already a hole from before, but it had been sealed up,
so I had to make a new one. And when I was drilling through the fire block, my drill bit
accidentally detached and fell to the ground through the wall. So yeah, never gonna see that
again. It's part of the house now. And then once I came down, luckily the cable was right there, but
I've had to run some cables since, and it was kind of tucked off to the side. And so an easy way to
find it was to use one of these cameras again, and then once you see it's like off to the side,
use one of these fiberglass rods. These are very inexpensive on Amazon. Use them to kind of run
cable. You can attach a lot of them together. But it comes with one of these hooks. Put it into the
wall, grab the cable, and pull it so you can reach it. Pretty simple. Then I cut the cable, gave
myself some extra slack to work with. I terminated one of the ends that was going to plug into the
and then used a punch down tool to add the other end into a keystone that will go into the wall.
That way the cables that are kind of getting messed around with more, that are like near the
switch, if those ever break, it's easy to replace a little patch cable versus running a new wire
from the wall all the way up to the ceiling again. And yes, I know that there was already a low
voltage box and I could have just added another keystone to that low voltage box and it need to
cut a whole other hole. But those cables came with the house, so they've been there for a while. I
didn't want to mess with them and I wanted them to be separate so that all the new wires that I'm
going to be adding are just going to be in a separate low voltage box. That's just what I
wanted to do. And then to mount the wireless access point, they have some holes that already
align with the low voltage box. So you just add those, snap the wireless access point in, and
that's it. Good to go. So yeah, I was surprised at how well all that went, because I was expecting
it to be a massive headache and take way longer, but everything went really smoothly. So what's
this big problem that I've been talking about? Well, it's with the next project. So for this
light strip project, I wanted to build my own. I didn't want to get some pre-assembled light
strips that have the power supply controller and LED light strip all together. And the reason for
that is I like to pick the controller, which I chose a Zigbee one to be a little more reliable
than a Wi-Fi one. And I wanted to choose which LED light strips I'm using. So I wanted to use
cob style because they look incredible. You don't see the little LED diodes. It looks just like one
big light bar. And I can also choose how long the wires are from the controller to the light strip.
So it gives me a little more flexibility. Well, I was planning on using some solderless connectors
that I'd used before on a previous project. And they make it really easy because they connect
the six wires without any soldering. Well, they don't work on this light strip because it's cob
style. So it's a little bit different than the previous LED light strip. So I was like,
I don't want to go buy something on Amazon or whatever. I'll just solder it. That was a big
mistake. Those little metal pads on the cob style light strips are so tiny and it took forever to
solder. I had already spent some time doing it. So I was like, I'm just going to power through and
finish it. And I did. And then I came over here and you're not going to believe what happened.
I looked in the bag for the light strips and I found a little connector piece that came with the
light strips. Yeah, that's right. These connect to the cob style light strips and connect the wires.
So I don't need a solder. You just press it down with some pliers and yeah, that would have saved
me so much time. I'm so dumb for not just checking that. Oh, so frustrating. After I put together the
light strips, I installed these channel covers, which I highly recommend if you're ever going to
mount some light strips. They help dissipate the heat and make the light strips stay up better.
And they help diffuse the light too. And I know it looks like one really long channel cover,
but it's actually two. There are two six foot long ones and I cut one of them down to four feet.
And to hide the seam better, all I had to do was swap the plastic covers and then it hides the
seam. So that's one little trick that makes it look a lot better. And then to hide all the cables,
I'm using some cable raceways that I stuck to the wall and to the cabinet. They hide everything
really nice. And then just one of those little cable management boxes down there as the power
supply and controller. And I know a lot of people prefer to put the power supply and controller
in the cabinet, just like get an outlet and install it in there and just hide everything
up there. That would look a lot nicer. And if I were doing that in my house, I probably would.
But this is the shop. It's more functional than looks. So this works fine for me. Overall, the
light strips turned out incredible. I love how they look. The only issue I have with these are
how bright the white LEDs are. So it can do warm and cool whites, which is why I went with these.
And people were saying on Amazon that they were bright, but it's mainly the RGB colors are bright.
The whites, not so much. It's fine for here, but if you're expecting it to be super bright and light
up the room, you might want to go with something else. And I'm sure I'll be testing a lot of other
LED light strips in here in the future. So it might be swapping out or something,
but I learned some very valuable lessons with both of these projects.
I need to slow down and double check stuff before just rushing through it all. That's
why the wireless access point project went so well. I double checked before I cut through the
drywall and everything went smoothly. The opposite with these light strips,
which turned out to be a massive headache. So mistakes were made. Hopefully you learned from me.
And, uh, yeah, there's a lot of really cool things happening behind the scenes
that I can't wait to show you. And thanks for watching.
