In your this video we demonstrate two straightforward projects to improve the airflow and air quality in an Airstream RV.
**Project 1: Replacing Ceiling Air Conditioner Vents**
* **The Problem:** The original vents on older ducted Airstreams (roughly 2016–2023) are restrictive and offer poor airflow, leading to uneven cooling. * **The Solution:** Upgrading to the newer style "open" vents used in 2023+ models. These are fully adjustable, can rotate 360 degrees, and allow significantly more air to flow through.
* **Key Installation Tips:** * **Tools:** Screwdrivers, a drill with a 1/8 inch bit, and a cordless driver for self-tapping screws. * **Pro Tip:** Use an old coffee can lid on your drill to catch metal shavings when drilling into the ceiling. * **Process:** Remove the old vent (which may or may not be screwed in), press the new vent into the hole (tabs will hold it temporarily), drill pilot holes, and secure with three stainless steel screws.
**Project 2: Upgrading Air Intake Filters**
* **The Product:** Clear2O Dust Guard Filters (MERV 6). * **Benefits:** These filters catch more dirt, pet dander, and allergens than the standard thin foam filters while offering less air resistance. * **Installation Process:** * **Template Method:** Use the old foam filter as a template to trace the shape onto the new filter sheet. You can typically get four filters out of one sheet. * **Preparation:** If your RV uses a plastic frame, cut the old foam out of the frame using a utility knife. * **Orientation:** Install the filter with the **blue side** facing the air inlet (the grate). * **Assembly:** Sandwich the new filter into the frame and snap the grate back into the ceiling.
By completing these upgrades, you show you how to achieve better-balanced cooling and cleaner air throughout the trailer.
*********** CAMERA GEAR ********************* Our Complete Camera Setup: Go to Camera - DJI Osmo Pocket 3 Dash Camera - BlackVue DR770 Still & Video Camera - Sony A7C Sound - DJI Mic 2 Flying Camera - Mavic Mini 4 Pro
ZEPHYR TRAVELS All Rights Reserved *This channel for entertainment purposes only. We are not RV or travel experts. We share our opinions and what works for us, but you should do your own research.
Chapters: 00:00 - Introduction & Project Overview 0 0:25 - Project 1: Upgrading Airstream AC Vents 0 0:57 - Comparing Old vs. New Vent Styles 02:32 - Tools Needed for Vent Replacement 03:05 - Step-by-Step Installation: Vents 05:39 - Project 2: Air Intake Filter Upgrade 06:28 - Demo: Installing on Different AC Models 07:53 - Benefits of MERV 6 Filters 08:11 - Tracing and Cutting the New Filters 10:15 - Prepping the Filter Frame 11:01 - Pro Tip: Proper Filter Orientation 12:09 - Reinstalling the Intake Grates 12:58 - Wrap Up & Final Airflow Tips
AI Generated·May contain errors
Video Summary
AI Generated
Randy from Zephyr's Travels demonstrates two projects to improve the airflow and air quality of an Airstream RV's air conditioning system: replacing restrictive ceiling vents with a more open design and installing high-efficiency custom-cut dust guard filters.
Well, hello and welcome to Zephyr's Travels. I'm Randy and today we're tackling a couple of
projects that we're going to improve the airflow of our air conditioner. So let's run that
introduction footage and we'll get inside and get going on these projects right away.
The first project is going to be to replace our ceiling air conditioner vents. These are the ones
that came on the Airstream and they're somewhat restrictive. There's not a lot of airflow coming
through here. You can also look at the back and see that they're pretty well blocked up. So when
you're trying to get air out of it, this doesn't flow a lot of air. These vents were used on
Airstreams when they started installing the ducted air conditioning, which I think was either 2016 or
2017, right up until probably 2023. After that, Airstream started installing these newer style
vents. Now these vents are much more open and they should flow a lot more air.
They can still be closed off and adjusted however you want. They also spin any direction that you
might need them to spin. So I think this is definitely a much better option for us. We've
noticed we don't get as much airflow in the living side of the Airstream as opposed to the bedroom
section. And I think that's a lot because there's so much more windows here that this area heats up
more than the back. And so the amount of air that we're getting here is having a hard time
compensating for the amount of sunlight that's heating this area up. So I'm hoping by installing
these that we get a little bit more airflow in this end and it balances out the Airstream better.
Though I do like the looks of these a lot better, so I may replace the ones in the back.
But then I can just adjust how much airflow is going through the rear vents and balancing it
that way better too. Now installing these is pretty straightforward. The first generation of
these just were held on with compression snaps across the back. They just popped in. If you're
like us, and after about a year these started falling out, Airstream started screwing them in
with a couple of screws. And ours had the screws retrofitted by an Airstream technician. So it's
just a matter of taking two screws out, pulling this out. Now this one you can see gets installed
with three screws. So we are going to have to drill some holes and put some screws in there.
So tools for this project need a couple screwdrivers. You're going to need a drill. And if you notice
here I've got an old coffee can lid on my drill. I use that so when I'm drilling in the ceiling
it catches all the metal shavings so that they're not going all over the place. It makes cleanup
much easier. And I do have a cordless drill driver because the screws they do give you are self
tapping. Though I'm going to start a pilot hole but I'm going to use a cordless drill driver
to send them in. So let's get started. All right we're going to start by removing the old vent.
And the best way to show you how to get the old vent out is to take this one right here.
And if you look right here in this slot there's an opening. It's kind of larger
and that's where the screws would go in. So you want to line that up with the screw and then you
can just take the screw out very easily. So the best way I found is get that lined up so that the
openings are there. And if you just slide this around you'll find the screw especially if you
like use a screwdriver as a guide. Well this one didn't even have a screw in it. So apparently
my ear string tech didn't replace them all. Now we're going to take the new one and there's
actually a little bit of a tab right on here that will hold this in place. So what you want to do
is just take this set it into the hole and press it in and it will stick in there
fine. And then you can come back with the drill. I'm using a 1 8th inch drill bit. Oh
high protection. And my suggestion is to drill one hole first and then put a screw in to lock
it into position and then drill the other two holes. There and I've caught all my metal shavings
in the drill. Airstream supplied stainless steel screws. So we'll take one of those
and install it. Don't over tighten it because this is just plastic and it will crack.
Once I've got one screw in place I'll drill the holes for the other two. Then install the other
two screws. Now I'm replacing three so I've already replaced one. I've got the second one
done. I've got one more over here to do. I will do that one off camera and then we will talk about
the next thing that it's going to suggest for improving the airflow. The next project we're
going to tackle is the air intake vents. And we've been using these Clear 2.0 dust guard filters
and they are they come in a sheet size that you cut to fit. And I'm going to show you one that's
been in there for at least a month of steady use. And you can see they do collect a lot of dirt.
So they do a really good job. So we're going to just replace the existing ones with these
new ones. But while I do that I'm going to show you a video where we installed these on a friend's
Airstream. And she had a little bit different style air conditioner. And I want to show you
how they will work on pretty much any style air conditioner that you can take the filters out.
So let's run that video right now and we'll come back and close this up. Our friends over at Clear
2.0 sent us a set of dust guard filters to install in our friend's Airstream. And so we're going to
go through the process of that to give you an idea how to install these on a different Airstream
than like what we did in our video. So I'm going to first cut these out. These are the cut to fit
size which will fit most RVs because you're going to cut them to fit whatever type of filter you
have which is simple. Now for those of you who haven't seen any videos on these dirt guard
they're a MRF6 filter. So that's fairly, they catch a lot of dirt and such. It's a good quality
filter. If you notice here on the filter it's got a blue tint to it. That's actually a coating on
here that helps catch the dirt better. They are good for airborne particles, pet dander,
and help you with allergies. So we've been running them in our trailer for since the first of the
year really. And I change them about every month but we've been in Florida for most of the winter
and so our air conditioner is running just about 12 hours every day whether it's heat or
cooling. And so our filters are getting quite a bit of use and I think they make a difference.
Two things that they help with obviously catching more airborne particles but the other thing that
seems to help is that they're less resistance for your filters too. So I think our air conditioner
blows a little bit more free because we have these in here. So what you're going to want to do is
you're going to pull your old filters out and I've got them right here. This is what was in there and
you can see it's just a very thin foam filter. But you want to take them out because you're
going to use these as templates to size up your new filters. And so I'm going to do it on the
back side and you're going to look at it and see what's the best way to get the most filters out of
this. And so if I put one here and do one right here, it looks like I can get four filters out
of this. And there's this uses two filters at a time so that's pretty good. So I'm just going to
take one of the filters and a marker and I'm going to just trace it and make sure catch all the
parts. You want to get all the little notches and everything that you got to cut into this.
And then what I'm going to do is I'm just going to go right across and mark up for all
the filters. Okay hopefully you can see this on the camera but they're kind of light but you can
see where I need to cut. So I'm just going to cut the shapes out. These cut very easy with just
regular scissors. So I haven't cut the notches out yet. I'll do that next. Now the way these
filters work they have a plastic frame and they go into the vent like this. And so we're going to
sandwich this new filter right in here and we're going to reuse the frame something like this. But
I'm going to take and cut this old foam out because I don't want to use the old filter part at all.
So I just got a little utility knife and carefully cut this out without cutting fingers
because Diane's sitting over here and she doesn't want to take me to the hospital.
Ours just connect onto the grills but these you need to have the little frame around them.
There. So now I have the old filter cut out. I've got the new filter here. You're going to put the
blue side to the grate. So in this case the blue side will be pointing up. You just want to kind of
size the filter on here. I got a couple little notches to cut. So I'm just going to take the
scissors. I'm going to take my scissors and it's going to come in here. Clip these little pieces
out. And I find this is easier to do once I get the rough shape of the filter. Don't try to, you
know, trace it all out and cut it all at one time. Cut the rough shape then come back and do the
little trimming for the little taps. So you want to put the the blue side. Compare one side's kind
of gray. The other side's got more of a blue tint. That needs to be facing the inlet of the air or the
grate. Drop it right on here and then this just snaps into place. So like this you need to adjust
it a little bit maybe to make sure everything's covered. And we're going to put these in place. I'm
Okay so now I've got the camera flipped. So you can see I'm just going to reinstall these
and the whole thing just snaps back in place with the new filter material.
Just like that everything's reinstalled. New filters, the grates fit in, everything should be
good. Well just finishing up our projects here. Got the new air filters in place. We're all done
for this video. So if you found this video informative and entertaining, either or, please
give us a thumbs up. We appreciate that. And if you haven't done so already, please subscribe to
our channel Zephyr Travels. We post new videos on a weekly basis. They can be how-to videos, travel
videos, campground reviews, all type of videos. So we'd love to have you guys follow along.
And until the next time, we will see you down the road. Take care everybody!