Looking for beautiful home decor on a budget? In today’s DIY, I’m transforming simple Dollar Tree fence and trellis pieces into high-end, designer-looking decor that you would never guess came from the dollar store!
These easy and affordable projects are perfect for adding a cozy, rustic farmhouse touch to your home without spending a lot. Whether you're decorating a shelf, entryway, or porch, these ideas will help you create elegant decor for less.
Music Courtesy of www.epidemicsound.com paid subscription https://linktr.ee/pattijgood My Channel - / @pattijgood My Other Channel - / @pattijgooddesign More Diys and Ideas - https://pattijgood.com/ My Favorite Crafting Supplies - https://www.amazon.com/shop/pattij.good Instagram: / pattijgood Tiktok - / pattijgood Facebook Page: / pattijgooddesigns Pinterest: / pattijgood
AI Generated·May contain errors
Hey everyone, welcome and welcome back to my channel. Today I've got some DIYs using Dollar
Tree fencing and trellises. And if you can't get the Dollar Tree fencing, Dollar General has some
that are very, very similar. So, if you want to know how to make them, stick around. I'll show
you how. Thank you so much for being here. I really appreciate it. All right, next one.
Okay, for this one I'm using four of the Dollar Tree arched frames and you can get these. They
have them this year. Next, I'm using one of the Dollar Tree fence sections and I'm going to cut
this to fit down inside of my frame. I don't want any edges showing, so these can be cut to fit right
inside of your frame. And I'm just using some cardboard scissors to cut this. This cuts this
really easily. And this is a good project if you want to use the Dollar Tree fence so that you
don't have any raw edges. You can completely put it inside of this frame and it's completely covered
up. And we're just going to cut it down at the bottom, just straight across, so it'll fit down
inside of our frame. And then you do want to cut the two sides off. You want to kind of make sure
that it is smooth. And you're going to cut all four of these to go inside each one of your frames.
This will sit down inside of this frame, so you can use those little tabs to bend back over to
hold this in place. Once you get all four of them done, we're going to take some E6000 glue, put it
right inside of the frame to hold this in place. And then we're just going to bend our tabs over
at the top to hold it in. And then we're going to do the same thing at the bottom. You don't need a
lot of E6000 glue, but we do need enough just to hold these in. When you're gluing the bottom, because you
don't have a lot of meat for it to grab onto, be sure and use some painter's tape to hold it down.
And then on the very bottom where that little v-shape is, we're going to put a little glue right
on each side. And that will touch against the frame and hold it in. And then go ahead and put
some painter's tape on top of that to hold it in place while it's drying. Okay, now that you got all
four ears done, we're just going to attach these together with some E6000 glue. And I'm going
towards the bottom ledge to glue these together. And then you are going to want to clamp these
pretty tight, just so that they do pull snug together. So you just got to really get a bunch
of glue on there. Not too much, just kind of smooth it out a little bit. I'm just using a craft stick
on this. And then I am going to put a little bit more. You just don't want it oozing out the top.
If it oozes out the back, you're okay because that's all going to be covered up. But just really make
sure that they are straight. And then you're just going to clamp them really tight. Now they will
tend to want to pull up on both sides, so you can put something with some weight on it to hold them
down while they're drying. And then don't skip that step because you do want this to lay flat.
And then I'm going to do the other two exactly the same way. And then we'll join the two sides
together in the center. But make sure that you are clamping these so that they do pull snug together
because you don't want to see a gap in the middle of them. After you got all that put together,
we're just going to take a piece of cardboard and we're going to trace our pattern out. So you're
just going to go all around the four arches and down the sides and down the bottom. And then we
are going to cut this out with an exacto knife. And this is what's going to go onto the back of
our fence. And then you're going to cut this out with an exacto knife and you're going to cut on
the inside edge of where you just drew that. Once you place this onto the back of your fence, just
make sure that you do have it pretty flush and you may have to trim out some pieces so that it
does fit inside that. You don't want to see it on the side so make sure that you do spend some time
trimming it so that it does fit inside the back of that fence. Okay, next I'm going to take some white
acrylic paint and I'm going to paint the entire side of this. And then once I get this side painted
then I am going to flip it over to the back and I'm going to paint the back black. Okay, after that's
dried I'm going to take some Mod Podge and I'm going to cover this side completely. Just put a
nice thin layer on it. You don't have to put too much but you want to definitely make sure that
every bit of this is covered with the Mod Podge. And then just set that aside and let that dry.
If you want to hurry the drying process you can always use an embossing gun or a heat source to
dry it quickly. Okay, after that's dried I'm just going to take a piece of tissue paper. I'm just
going to lay it over the top part of here and then I am going to iron this on. Now I am going to cut it
in half and put half of it on one side half on the other lengthways like this. Just make sure that if
you are cutting your tissue paper that you're coming into the middle of where the seam is
so that your frame will cover that up. Okay, next I'm just going to cover this with some parchment paper
and then I'm taking a little iron to iron this. And this is the little Cricut mini iron and it
works great for these projects. But you want to spend some time making sure that this does get
ironed on good so that it is completely flat all the way across. And I got my tissue paper from
Amazon. I'll give you the link for this and it comes in a variety of different colors. Okay, once
you get it all on there then we're just going to trim around leaving about a half inch overhang
all the way around. And then we're going to cut little slits in this and we're going to glue this
to the back. And that way you don't see the side of the cardboard. It's completely covered up. And
then we're going to cover up this back so you're not going to see any of that tissue paper here in
a little bit. To glue this I'm just going right along the ledge of the cardboard and I'm just
going to glue this right to it. I'm not going to glue my tabs yet with the hot glue. Just pushing
it up against the edge just to make sure that it is pretty flat along the edge. And then once we
get that done then we'll start using some Mod Podge to attach the tabs. Just kind of fold them
over and glue them down. And then you're going to go all the way around until you have all your tabs
glued in. Next I'm just going to trace this out on some craft paper. And I'm just using the craft
paper that I had on my workstation. I just flipped it over so it was clean. And I'm just going to cut
this straight out of the craft paper and we're going to glue this to the back. This will kind
of finish it out and I'll have a nice back that's finished. And you don't have to use craft paper.
You could use any kind of paper that you want to but it kind of makes it look like when you take
your picture to the framing company to have it framed. They put that backing on it that's made
out of the craft paper that just covers it up. And I'm just going to use some regular Tombow glue.
You can use Elmer's glue or anything you want to. I'm just going to kind of go all the way around
the edges and glue this down. This will just really finish this out nicely. And then just keep going
until you have it completely glued in. And if you want to add just a little personalized touch to
your projects, I just got this self-inking stamp with my little logo on it and I'm just stamping
it on the back of my project. Next attach this to my frame. I'm just going to use some E6000 glue
and I'm just going to put a pretty good generous amount all the way around. Just really get a lot
of glue on there because you really want this to hold in good. And then once you get all your glue
on we're just going to lay that onto the back of it and we're going to put something heavy on it
to hold it in place. And to speed up the drying process while the E6000 glue is drying, I am
putting hot glue all the way around the edge. Okay next we're going to add our backing and we are going
to push this down inside the frame. So spend some time really pushing it in so that it does catch
onto that hot glue and stays in place while your E6000 is drying. And then flip it over and put
something heavy on the front to hold this in place. Okay next I'm going to take a 1x4. I'm just going
to cut it to the length of my frame. So go all the way down to the end. You don't want any overhang.
We're just making a little shelf to go on here. And next I'm going to come into the center of each
one of my frames. I'm going to take a nail setting tool to kind of punch a little hole in the center
here because we are going to put some screws through here. So start with that and then we're
going to take an ice pick to run it through the rest of the way and then we're going to drill it.
You want to do this on this plastic because you don't want to break the plastic. So kind of spend
some time on this part. I'm using an ice pick to start my hole and then I'm going to use a drill bit
to go through the rest. And I'm going to put a screw hole in the center of each one of these frames.
And then I'm also going to put one on the outside edge of both sides. But just kind of spend some
time doing this part because you do not want to crack your frame. Okay next I'm going to start with a
small drill bit and I'm going to start drilling all of my holes. So you have two on the outside edge
and one in the center of each one of those frames. And then once I get these holes drilled then I'm
going to come back with a larger drill bit that matches the screws I'm using to drill a bigger
hole. Next I'm going to attach the frame to the back of this piece of wood. I'm going to take my ice pick
I'm going to punch it through to get my first hole lined up and then I'm going to drill that hole out
with a drill bit. I'm sorry I got out of camera there but just going to drill a hole right into
the bottom there and I'm going to put my first screw in just to get it lined up first and then I'll be
able to do the rest of them pretty easily. And I'm going to put a washer on the back of it so it
doesn't pull my cardboard in all the way. So put a washer in there first then get your screw put
in there and then go ahead and screw it into the piece of wood. That way you'll have your first
piece already put in there and you can line the rest of them up after that. And once I got that
one done I'm not even going to drill a hole through these next ones. I'm just going to go ahead and
screw them right into my piece of wood. It worked just fine. And just keep going until you have all
these screwed in all the way down. But definitely you want to use a washer because you don't want
it pulling your cardboard in. And you can use any size washer you want. I think these are about a
half inch washer but just make sure that the bottom edge of your frame is down to the bottom
edge of that piece of wood. And just keep going until you have them all screwed in. So I'm just
going to run a piece of painter's tape all the way against the edge because I am going to paint my
shelf. And you could have done this before you put it all together but I didn't do it that way.
Just make sure that the front is completely covered. And I was going to stain it but I was
scared if it touched the paper at all on the tissue paper it might bleed through the rest of
them so I am painting this instead of staining it. I'm just painting this with a chalk paint
and I'm just using a sponge brush on this. And this actually ended up turning out really good.
I liked it better than the staining idea. Next I got these little terracotta pots from Amazon.
They measure one and a half inches. And then I got these plants from Amazon too. They normally come
in a white flower pot but I always take them apart so I can use them on projects like this.
And I'm just going to take a rubber band to tie around the bottom of them to hold them in place.
And then I'm just going to glue them right down into the bottom of my pot. Just kind of really
put them together like that and then go ahead and put hot glue into the bottom of your flower pot
and attach them. And then I did decide to attach that second one and so I'm going to pull it right
into the rubber band as well. Just make these as full as you want to but you just kind of want to
make them full enough so you don't see the inside of the terracotta pot. And I'm just putting hot
glue all the way around the ledge of it and then pushing these in. And then I'm doing two more that
have a little bit different plant in it. And this is the plant that I got from Amazon. This is the
one I was saying that I take it apart just pull it out and then you can start using it on other
projects. And I'm going to rubber band these together and then I'm going to do another bundle
that's very similar. And you can use any kind of plant you want to or you could even put flowers
in these if you'd rather. And these are what's going to set up on my little shelf.
For this next one I'm going to use another piece of fence from the Dollar Tree and I'm going to
frame this in and I'm just using some one by twos on this. I'm just going to kind of get it together
to where it's going to be framed in and you don't see any of the edges once I cut those off.
And I'm just kind of mocking this up with some scrap wood right now. And then I'm going to mark
my two side pieces and I'm going to cut those at seven and seven eighths inches each. And then I'm
just going to mark it with my square and I'm going to cut two of these. What I do is I just go ahead
and cut one and then I line the second one up with it just to make sure that they are exactly
the same. Now that I got my sides cut I'm going to go ahead and measure across the top and I'm
going to cut two pieces at 24 and a half inches in length each. And I'm going to use the piece of
wood that I cut my two sides from so it has the same color to it. And I'm just going to mark it
with a square and then just go outside and cut these off. So 24 and a half inches is what those
need to be. Okay now I'm going to build my frame. I'm just going to take some wood glue to attach these
and then I am going to clamp these in place. And then we're going to put our fence onto the back of
it. So go ahead and make your frame and then pull it together, clamp it, and then get any of the
excess glue off while it's still wet. And I'm gonna clamp both sides of this and then put it aside and
let it dry. Just make sure once you get it glued together and you get it clamped that it is square.
And then be sure to get the excess glue off of it because we are going to stain this.
While that's drying I'm just going to take a staple gun. This is a rechargeable one. I got
it from Amazon. I'll give you the link for it. And I'm using half inch staples on this and I'm putting
about three staples on each side on each corner. This will really hold it together good. And then
this staple gun really doesn't take a lot of effort to use. It doesn't take a lot of power
so it's really easy for people who have weak hands. Okay next I'm going to take my fence. I'm
going to put it on the very back and then I'm going to kind of mark where I need to cut it
on the bottom. And then I'm just using some miter shears to cut this. I'm going to kind of go long
at first and then I'll cut it up a little bit higher. And these worked good with this because
they didn't end up splitting it. It did give it a nice clean cut straight across. That was a little
bit long so I am going to cut them a little bit shorter there. And then that way this will fit
perfectly inside of our frame. And then I'm using a oil-based stain. It's by Minwax. It's called
Honey Colored. And then I'm just going to apply it with a soft rag. I'm going to start with the
back because I am going to do this and flip it over and then do the front. But just kind of really
get it on there good. I think I ended up doing two coats on this to get the color that I wanted
but I think this really looks good with the black fence. It really kind of set it off. After that's
dried I'm going to go ahead and attach my fence. And I'm just coming to the back, the part that
had the staples on it. And I'm just going to staple this on. Now just kind of really line it up. Spend
some time on this so that you make sure that your arrows when you turn it over are exactly in the
same place. And I'm putting maybe you know three or four staples per top of each one of my little
pieces. And I'm going all the way around and down the sides as well. So just put plenty of staples.
You're not going to see them but you want to make sure you put enough on there that it does hold in
place. And you can use as many staples as you want because you are not going to see them. I did put
quite a few on here. And I'm going to run them down the sides and on the bottom as well. And then kind
of stretch it tight as you're doing it too. So that it does pull good and doesn't have any slack.
And then when you're doing the bottom one just go ahead and pull it snug as you're stapling it.
Just kind of pull it on down there and just make sure that it is pretty snug. And then get plenty
of them down each side as well. Okay next I got these little 90 degree angle pieces from Lowe's
and I'm going to spray those with a Krylon matte black paint. And I'm putting one of these at this
corner and one at the diagonal from this corner. And I'm just going to use my nail setting tool to
kind of mark my holes. And then I am going to come in with a drill and drill out the hole. And then
I'm going to put my screws in through there. Just kind of make sure it is lined up good. And then
just knock your holes in there really good. And then go ahead and drill them. This will keep your
wood from splitting if you pre-drill. And I'm just using a small drill bit on this and I'm not going
all the way through. Just enough so I can get my screw started. And then I'm going to do the same
exact same thing at the other side at the bottom. And then I'm just using some small black screws
just to attach this. You just want to make sure that you have it just where it won't go through
that bracket and it'll stay on. I think these ended up being maybe like a number six screw
but they worked out perfect. All right and that's pretty much all I did on that. I think that turned
out super cute. Let me know what you think. For this next one I'm using one of the wagon wheels
from Dollar Tree. A basket and a trellis all from the Dollar Tree. Now I saw several of these on
Pinterest but I'm doing my own take on this. And I'm just going to cut my wagon wheel in half and
I'm just using my pliers to do that. And I am going to snip off the bottom. Some people pull them in
to the wheel but I just wanted to kind of get them off of there. And then just cut your wheel just
straight across so that you have a half of a wheel complete half of a wheel. And you can cut this with
pliers. It worked pretty good. Just get your main spokes off of there on that one side and then you
can cut through that circle pretty easy with the pliers as well. Just kind of get those out of the
way so that you have room to get in there and then you can just start cutting that center piece in
half. I'm going to do the same thing for my basket. I'm going to cut it in half but I'm actually going
to cut it to where it's not completely in half. I'm going to leave the main part of it that I'm
going to use a little bit bigger. So I'm probably coming in about two-thirds of the way to cut this
basket. And just go straight down the center. Just cut each one of the little prongs and then you can
cut the bottom pretty easy as well. And then you'll just have two halves and I'm using the larger of
the two halves. And this doesn't take a lot of work. I mean your pliers will cut through this
basket pretty easily but you do want to completely cut it in half and you want to kind of try to make
sure that you got it straight across. Next attach the wheel to my trellis. I'm just going to use some
black zip ties. And two of these held this really good. Then we're going to zip tie it to our basket
as well. But pull it as tight as you can. Pull it around to the back and then really tighten that up
and then that will stay in place good. And then I'm coming down to the bottom and I'm going to
attach one down at the bottom as well. Now that little u-shape notch that's going right into the bottom
of that trellis. And then that'll kind of hold it in place. But you really want to pull your zip ties
as tight as you can possibly pull them. And then they will stay in place and then just cut off the
excess once you get it tight. Next kind of position your basket up there and then we are going to run
the zip tie through the bottom of the basket and hook it to the wheel. And then that way that wheel
stand up perfectly. Just kind of feed it through there and then come back up through the basket
and then just tighten that up. And we're going to add two more down at the bottom of the basket
down to the trellis. And you're going to do that on the opposite side as well. And then once you get
the two bottom sides done then we're going to go ahead and do the top edge to the trellis as well.
And this will hold together really good. This stayed together. It was pretty tight once you get all
these zip ties really tightened up. And then just cut those off and then you're going to do the two
at the top. And then this will be strong enough if you do want to hang this outside. It will stay
together good even outside. And now I'm going to take it outside and I'm going to spray paint it
with a Krylon Fusion in matte black. Okay next I'm taking a piece of pipe insulation and I'm just
going to wrap it around the wheel to make a tire. Now this has a split in it. You get these at Lowe's
or Home Depot either one. Any hardware store will have pipe insulation and you're going to zip tie
it and then you're going to have to add another zip tie too. And you're going to have to put these
on pretty tight to keep it underneath the basket. And then just pull it around and form it around
the wheel and then zip tie it down at the bottom. And just really make sure that you do get your zip
ties tight and then just cut off the ends on them. So I'm taking one of the cocoa baskets from Dollar
Tree and then I'm just going to shape it into my basket so it's completely up at the top. Okay next
I'm going to take a piece of floral foam and I'm just going to cut it so that I can put it down
into the bottom of my basket. You don't need a lot just enough to go down into the bottom.
So I got these flowers from Amazon. I got several bundles of these and I'm just going to cut these
off a little bit short because I want them to go down into my basket a little bit farther.
So I'm probably coming down to the second little notch on these and I'm just using some wire cutters
to cut them and I'm going to do that to all the bundles and I'm going to kind of spread them out
and push them down inside to my little styrofoam. And it's easier if you have your styrofoam out of
your basket to do this but I'm going to put a bunch of these in here because I do want mine to
be really full. Okay then once you got it as full as you want to then you can just start kind of
spreading it out and shaping them a little bit. Then I'm just going to sit this right back down
into the basket. I'm not going to glue it in. I'm just going to stick it in there and then I did go
back in and add a few more flowers. All right that was pretty easy.
Okay I hope you enjoyed the video today. I hope it gave you some inspiration. If you like these
kind of videos be sure and give me a like, subscribe, and ring that bell to be notified
when I have a new video upload. Thank y'all so much for being here. I really appreciate it and
if nobody's told you today, you're awesome. See you next time. Thanks for watching.