Super easy DIY stand for aquariums or terrariums

Mini World Craft
6 followers
AI Generated·May contain errors
Video Summary
AI GeneratedThis guide demonstrates how to build a professional, cost-effective DIY wooden stand for aquariums, terrariums, or insect enclosures. Using 2x4s and plywood, the creator explains the entire process from precise measurement and structural assembly to sanding and staining, ensuring a sturdy and polished result that is significantly cheaper than retail alternatives.
Custom aquarium stands are a huge money saver. In fact, every stand in this room was custom made by
me. It saved me a whole bunch of money versus if I were to buy them, but not everybody knows how to
make them. Some can be complicated and some can even be a bit more involved than others. So today
I'm going to show you guys how to make a simple DIY custom aquarium or terrarium stand. Now,
I am going to be using this stand for my mantis enclosures as I have quite a bit of them and I
need somewhere to put them, but this exact same technique can be applied for aquariums, terrariums,
and really anything you need. So with all of that said, the first thing we need to do is go to the
garage and take a look at the materials that you'll need. Okay, so we're now here in the garage. The
first thing I want to go over is the materials that you'll actually need to make this thing,
starting off with six of these eighth inch thick plywood pieces, followed by eight two by fours
that are eight feet long. You also need a couple other things such as a paintbrush, drill and
screws, and a nail gun or a staple gun with brad nails, and then either stain or paint, whatever
you prefer. All this stuff you can find at most home improvement stores, but I get mine at Home
Depot. And then again, if you don't have something like a nail gun or even a staple gun with the
brad nails, you could just use nails and a hammer. That's pretty much all you're going to need for
this. So with that out of the way, let's get to the project. So the first thing that you're going
to want to do, first of all, is actually take the measurements of what you want. Now, the dimensions
of the stand that I'm making is going to be 48 inches tall, 40 inches wide, and 14 inches deep.
But again, you can adjust those measurements however you want to get the stand that you need
for your project. The first thing we're going to do is take one of our two by fours and use a tape
measure to measure to length. In my case, this is 48 inches. After measuring and marking for where to
cut, bring it over to a saw. A circular saw works best in this instance, but you could also use a
hand saw. However, it'll take a little bit longer and the cut won't be as clean. You could also use
a table saw if you have one, but I find circular saws to be the best. Anyway, after double checking
my measurements just to make sure I know where to cut, I went ahead and cut the piece. Now that the
first piece is cut, because these are a very strong support piece and basically the main part of the
frame, we are going to need four of them. An easy way to get more of the same piece is to lay down
another two by four and then set your pre-cut piece on top of it. Then line it up with the saw
and cut along the edge. After that's done, go ahead and repeat this process a couple more times to get
all four pieces. So with the four main pieces cut, the next thing I'm going to do is work on the
width pieces, or the pieces that go across the stand and also hold the shelves on top. Now the
easiest way to do these in the way that I'm going to do it is starting off by measuring the piece.
Now again, as I said earlier, the width of mine is going to be 40 inches. However, I want to go
three inches down to 37. And the reason for this is because this piece will be in between the two
other pieces and two by fours have a thickness of exactly one and a half inches. Therefore,
accounting for this thickness and cutting the piece a little bit smaller, putting it in between
the other two pieces will give me a length of exactly 40 inches. Once you've calculated your
measurements, go ahead and cut the piece to size. Before moving on to cut the rest of the pieces,
I like to do a little bit of a test fit as well as make sure that the piece is the correct length.
I start by assembling everything together and then go ahead and measure it. As you can see here,
a perfect 40 inches. The next thing to do is account for how many shelves you want. The first
thing you need to do is take the full measurement of the stand. Then we need to account for the
thickness of the two by fours. In this case, I'm going to have four of them, so I need to subtract
a total of six inches. Then go ahead and divide that number by three and that'll give you the
total length between each shelf. However, because I left a little area at the bottom for an extra
two by four, I need to subtract a total of one and a half inches from everything, giving me a
measurement of 17.5. It's a little bit of a complicated process with a lot of math involved,
but it's necessary to ensure that we get the correct length between each shelf. With that
out of the way, we can go ahead and continue to cut the shelves. Since we're going to be having
two frames, however many shelves you'll have, you'll want to cut double the pieces. In my case,
I ended up having four shelves, so I cut eight pieces total. Following the same process as I
did before where I just overlapped the pieces, line them up with the saw and make the cut.
Once all eight pieces are cut, we need to start assembling everything together. Start by laying
down the side piece followed by the top piece. Then for the bottom piece, account for the
earlier. Now we need to attach everything together using a drill and some screws. The
screws I'm using are some two-inch multipurpose construction screws, but any wood screw will work.
I recommend pre-drilling the holes, so find a drill bit that's slightly smaller than the thickness of
the screw. Then go ahead and line up the top piece with the side piece in the corner. It's important
to do this on a flat surface to ensure everything is level. Once you have everything pressed firmly
together, go ahead and start pre-drilling the holes. When drilling, it's important to make
sure that you go all the way through the first piece and into the second piece. This will help
make sure that the wood doesn't split when we attach the screws. Once the holes are drilled,
go ahead and add the screws. This will secure everything together and make sure that it's
attached firmly. Then you'll want to repeat this step for the bottom piece. Like I said earlier,
we need to account for the thickness of the 2x4, so use another 2x4 to space that before you drill
the holes. Then go ahead and pre-drill the holes and add the screws to secure it in place. By doing
the top and bottom shelves first, it makes it easier to space the other ones. Anyway, after
doing that, go ahead and attach the other side piece. Once the main frame pieces are all attached,
go ahead and take that number that we calculated earlier, which in my case is 17.5, and use that
to space each shelf. Then, like earlier, go ahead and pre-drill the holes and secure everything
with screws. Repeat this process for each shelf, as well as repeat the entire process one more time
to get two identical frame pieces. It takes a little bit of time, but it's necessary.
So with both the front and the back frame complete, the next thing we need to do is the side pieces.
Now, unlike the width pieces that are going across, these pieces are going to go from front to back,
and these can be whatever length you need them to be. So like I said at the beginning, the dimensions
for mine, the depth is going to be 14 inches, so I'm going to cut these pieces 14 inches. Now,
depending on how many shelves you have, you're going to need one for each shelf. I have four
shelves, but I'm only going to make three because the bottom shelf really doesn't need any. That's
the reason I left that small gap at the bottom, is just in case you want to add another support
down there, you can totally do that. However, my shelf is not going to be supporting a whole bunch
of weight and probably won't need that, so I'm just going to forego that. But if you have heavier
things on that, you definitely want to add that piece for a little more support. Unlike the other
pieces, this is going to be going front to back with no obstructions, so we don't have to account
for anything. Measure out your length, and then cut it to size. It never hurts to double check
your measurements before making the second cut, so that's exactly what I did. Once I confirmed that,
I went ahead and cut the other pieces. Again, following the technique of layering the boards,
pushing it flat up against the blade, and making the cut. As for how many you'll need,
it'll depend on how many shelves you'll have. In my case, I have four shelves, so I'll need eight
of these total. Once you have all the pieces cut, lay down one side of the frame, and put the 2x4
in place. Again, it's important to do this on a flat surface to ensure everything is level.
Then go ahead and pre-drill the holes, and secure it with screws. Repeat this process for each piece
underneath each shelf. A little bit of a tip to ensure that everything is level, is while you're
drilling, make sure to push down on the frame itself. This will make sure that everything is
level, and that we have no inconsistencies later. Once all the pieces are attached, go ahead and
set that piece aside, and then get the other frame and lay it down. Then grab the other piece,
flip it over, and lay it down on the stand, making sure that the 2x4s are under each shelf.
Then go back and pre-drill every hole, and secure it with screws. Once that's complete,
you can go ahead and set it upright, and that completes the frame. So our frame is now complete,
and as you'll notice right now, it might be a bit wobbly, a bit unstable even, and that's
completely fine. You can put a few extra 2x4s in there just to stabilize it, or just put a few more
screws in. But once we add the paneling, that should stabilize everything, which is the next
thing we need to do. Now, what I use for paneling is I use some 1-1-1-1, like, plywood-type stuff.
Again, you can find this at pretty much any home improvement store, but I get mine at Home Depot,
and the process for adding it is honestly pretty simple. I usually start with the sides, so I'll
take my measurements. In this case, I'm not going all the way back, just covering with the 2x4,
so I'll take the measurement for that, then take it out to a table saw. Alternatively, you could
use something like a jigsaw or even a handsaw but again this is going to take
a lot more time and the cuts won't be as clean. Using some of that paneling that I
showed earlier I measure and mark for where to cut and then go ahead and run
it through the saw. This can be a bit of a dangerous process as this is obviously
a very dangerous tool so be sure to keep your hands away from the saw blade. Anyway
continue running the piece through the saw blade smoothly and evenly to make
sure that you get a nice strip. Then go ahead and run it through as many times
as you need. In my case I need four but these won't quite reach the bottom so
I'm gonna cut a couple extra just to be sure. Once the piece starts getting super
thin a little tip is you can use another piece of wood such as a 2x4 to help
push the piece against the back. This way your fingers won't get too close to the
blade. Additionally instead of pushing through you can start pulling through
which again will keep your fingers away from the blade. Once all the strips are
cut go ahead and align them with the stand. I'm going to be overlapping a
piece on the front so I'll account for that before securing it in place with
some brad nails. Cutting the other pieces follows basically the same process except
this time you want to account for a little bit of overlapping. What I mean by
that is instead of just taking the measurements of the 2x4s and transferring
that onto the paneling you want to account for the paneling that's on the
side of the stand. All you have to do is put that on and then take the
measurement again, cut the piece, and you should be good to go. As I mentioned
earlier some of the strips aren't quite long enough to reach the bottom. To fix
this I cut a few extra strips, set them along the bottom, then mark for where to
cut. After that I took them over to a saw and cut along the line. Similar situation
for the pieces going across. Most of these pieces are a little bit too long
so again I'll set it in place, mark for where to cut, make my cut, and then bring
it back over and attach it. Since the shelf will be going on top of this I
want to account for more of that overlapping that I mentioned earlier. To
do this I'll get another little piece of the paneling, set it on top, and then
secure everything with more nails. Then just repeat this process covering any
little part of the stand that you want to. It can get complicated at times but
in the end the results are worth it. At this point you may start to notice that
there are a few little pieces that kind of stick out as well as a few pieces
where there may be gaps. All of this is not important right now and we'll fix it
up later. Then for the actual shelves it follows basically the same process as
the rest of the paneling. Take your measurements, then take it to a table saw,
run it through, then bring it back, lay it in place, and secure it with some nails.
Go ahead and repeat this process for each shelf. It should be pretty simple as
you can just copy the measurements for each piece. At this point the stand's
starting to look pretty good. If you want to cover the 2x4s on the inside you
can. I'm going to because I feel like it looks better, but this is by no means
necessary. If you're on a budget and just can't do it or don't feel like it, there's
no reason to do this. It's more of an aesthetic thing and it'll really look
fine either way. Hey there! Okay so the paneling is now finished. It is kind of a
long, tedious process and sometimes it can even be a bit complicated and the
reason for that is basically just because it's very personal. And what I
mean by that is like you can really do it any way. There's no right or wrong way
to do it. Like just cover whatever you want to cover, leave open whatever you
want to leave open. For example, like I said, you could leave those inner parts
open if you want. Don't mind the look of the 2x4s or you can cover them up.
You don't have to cover it as much as I did. I just like to do that because it
looks nicer, but if you're on a budget or you just don't feel like doing it,
there's really no need to. But anyway, once the paneling is done, like I said
earlier, there are a few messy parts like a few pieces sticking out or a few holes
or a few gaps and stuff. That is the next thing that we're going to take care of.
So for any little like cracks and stuff, using some sort of wood filler is
probably the best way to do that. Just get it on the end of a knife or a paint
scraper or whatever you really have. Just start filling those holes
individually. I don't have a whole bunch of gaps on mine, so I'm just gonna forego
this process. And as for everything else, what we're gonna do to take care of that
is sand it. Now luckily, the specific paneling that I use is a very soft type
of wood, so it sands really, really easily and fast, which makes stuff like this go
a lot faster. What I'm gonna do is I'm just gonna go over the whole thing and
I'm just gonna sand down all the corners, make them smooth, round, and then flatten
anything out. Sanding can get a bit dusty, so make sure to wear your protective
gear. As for the sandpaper I'll be using, it really depends on how smooth you want
it, but I find 180 grit to be sufficient. If you don't have any power tools to do
this, you can do this by hand. However, it might take a while. If you do have an
electric sander though, it expedites the process substantially and makes things a
lot easier. The name of the game here is basically just to go over every surface.
You want to smooth all the sharp corners, as well as those little areas that are
jutting out like I mentioned earlier. Luckily, this wood is very soft, so it
makes for a quick and easy sand. Bigger stands can sometimes take a little bit
longer to sand, especially if you have areas that are sticking out quite a bit.
I had a couple of those on here, but overall it wasn't too bad. After a little
bit of sanding, you'll now have a nice clean stand. The next thing we need to do
is stain it. The color I'll be using is dark walnut. I recommend using water-based
as opposed to oil-based. I was an idiot and accidentally bought oil-based, but I
highly recommend using water-based. In order to apply the stain, you can use a
paintbrush or a rag. A lot of people prefer to use rags, but I find paintbrushes
to be sufficient. It's really up to personal preference and whatever you
find easier. As an alternative to stain, you could also use paint, which will look
just as good. I like to use stain, though, just to get that natural wood texture. An
important thing to note with stain is that a little bit goes a long way, so
depending on how dark or light you want it will determine how many coats you'll
need. I only wanted one coat, and I also tried to put it on as light as I could. I
went over the entire stand, making sure to cover everything. It's also important to
wear a mask during this process, as well as doing it in a well-ventilated area, as
stains can get pretty smelly. That's one of the benefits of using paint, as well
as being able to use something like a paint roller to make this process go
faster. However, like I said earlier, I prefer the look of stains. In total, this
process took probably about 45 minutes, but eventually I got it done, and the
stand was complete. So now that the stand is stained, I really really love the look
of it. I think the color is a bit darker than I wanted, but I think it'll be fine.
Now there are a few optional things you can do from here. One is that you might
want to apply some sort of some sort of polyurethane, and that's okay. You can do
that, but then you're gonna have to let it sit outside for like two to three
weeks, just so the smell dissipates. And even depending on the type of stain
that you're using, you could even have to let this sit outside for a while. But
other than that, it's pretty much finished. Again, unless you want to add
some sort of polyurethane to protect it from water, just give it a shine. But other
than that, it's done. Now we just gotta move it downstairs and get all the stuff
on it, and we should be good to go. Hey there! Thank you guys for watching. I
really really hope you guys found this tutorial helpful. As of right now, I kind
of just put a few things on this just to make it feel a little bit more full, and
the lighting situation is just temporary. I do have some puck lights coming that
I'm going to install in here, but unfortunately those didn't come in time.
So I'll post a few pictures and maybe a short once I get this updated. Now as
you can tell, this shelf is pretty empty for the most part, and the reason for
that is because I wanted to give myself enough extra space, because as of right
now, I only have four mantis enclosures actually built. I think I am going to
keep the isopods on this setup just because I feel like it looks good, but I
am definitely planning on getting more mantis species, as well as I have a
couple others that aren't quite big enough to go into an enclosure yet, but
will be soon. But again, that is going to do it. If you guys have any questions
about the build, make sure to leave those down in the comments. Don't forget
to leave a like, and make sure to hit that smash subscribe button, and I will
see you guys next week!
