How to make a bow form

Crossbows Legacy
11 followers
28 Video Views·Jun 8, 2026
AI Generated·May contain errors
Morning everybody. Today I'm building a new form. I'm starting to make a couple of recurves.
So I've already made a handful of recurves but it is still just dialing it in.
So I just wanted to show you how I make a form. In Australia we've got this stuff called
yellow tongue. It's used for flooring. It's literally got a yellow tongue in it.
This is made for flooring. The point is it's 19mm which is perfect. You put two pieces together
creates 38mm which is how wide most people will build a boat. It's one and a half inches 38mm.
So it basically works out perfect. This stuff is crazy strong. It's flat as and it's cheap.
So you can buy a sheet like this which is 1800 long from Bunnings. I think they're only
$30 I think it is. Basically rip it in half and then you end up, I'll show you when that's
already somewhat done. Here's another one of my old forms. So you're literally putting two together.
You route it. I'll show you how to do all that and then I just put a bit of reo bar through
and then you're strapping it down and I just put a piece of wood on the bottom to keep it
straight this way as well. Basically it works perfectly, pretty easy going.
Pretty fast, easy way and cheap to make some forms. As we get to it,
basically start with this 1800 length and we'll rip it in half.
All right so the next piece of the puzzle. I used some, there's a normal plywood I think it's
6mm, 7mm, whatever it is. 8mm, 9mm ply. It doesn't really matter that much. Mainly
easiest one to use. It's something that you can shape pretty easily. Come up with a bit of a
design. Most of my bows have between 18 and a 20 inch riser. It seems to work for me. It's a
good balance between small and big sort of thing and then come up with a nice curve whether you're
making a recurve or just a nice long bow or something like that. The main thing is when
you're making this where it gets to the centre point you're going to be using a router. So if
you go past that you either want this piece here to have a little bit of both the curves in it
or you really need to make sure that you stop right on the centre when you're routing it.
And this is basically a guide so that you get it exactly. Then you go from this side, flip it over
to the other side. I then drill a few holes in and that's to put screws in to hold this very secure.
On this piece here we've got to be marking the centre. You've got to screw both these together
then you mark the centre so you get your centre line and you cut this nice and straight so that
you've got a straight edge for the bottom of this template to go onto. It keeps everything
nice and straight and perfect. Nice and easy and then we use a couple of different types of routers
to get the desired effect. Let's just use the hand router, nothing fancy.
Just two different style bits and that's about it. So we'll just lay this out a little bit and
we'll get you a bit closer. Next part is I put the template onto one piece of board first
and then I can cut the excess out and then we route just the last few millimetres to make it
perfect. The reason I do that is it makes it a bit easier to put into my bandsaw and everything.
You don't have to have a bandsaw, you can just use a jigsaw or anything like that. It's the
router that makes it perfect. Just for where my shape comes down, the nock's actually like here
so I need to make the form a little bit longer just to have more glass down there.
So I'm just going to put like a 50mm line up from the bottom all the way across
and you just line up your template from there and your centre line
on that marks, making sure you're as perfect as you possibly can.
And then you're basically just putting your screws in, make sure nothing's really moved,
make sure everything's as good as possible. Okay and that's holding that nice and straight
and the main reason you do that, now you mark it and those three holes will always be
in the same spot so then when we go to route it, that's all in the exact spot.
Then you just draw your template on. I'll just extend up my line for my
thing. Okay so that's one side done and then all you're doing is flipping it over
and doing the exact same thing on the other side.
Move just a little whisker.
And the same thing on this side. I'm going to draw that around.
There we have it. The design is now transferred over.
Doing good. That's it. Now we're going to cut that out on the bandsaw and then we've got
the basis for our pool. All right so then up next you get your two pieces.
So all I did is do this one, see how I've cut just for a few millimeters to the line
and then I'll mark this one, mark center on it, traced it, cut it out as well. So they're both
just a little bit oversized basically. Now you're going to line these two up.
Yep I'm pretty happy with everything. Make sure everything's good. Yep I'm happy with everything.
This top piece pre-drilled. I just do a couple inches from inside all the way around and that's
going to get screwed from here through into the next board. You pre-drill it so then you're pulling
this into the other board. Grab some wood glue, glue the form up. I'm doing everything on this
bench here just because this bench is basically perfectly flat. I'm going to be all the way around
right on the outside, chuck them together. It's a good idea to clamp this so I'll go grab a couple
of clamps. It's also good if you can try to get them actually sort of level with each other.
Sorry not level but square. This makes it a bit neater when you're on to the next piece of wood.
So
pretty good. Then just screw it down. Just grab the um you know basically the right length screws.
My actual normal screw gun is diving over there. All right so we're gonna be doing the next part now.
So you can sort of see here a little bit I've just got the two pieces of timber glued together.
Everything's screwed together, glued together. It's been sitting for a bit. I've done it on my really
flat bench. It's all nice and straight. I've chucked a couple clamps on it to hold it all in place.
Now the whole reason you put a few screws in, now you can just put it straight back in.
So now your form, so your template is now put back onto your form in the exact same position.
So now it's time to get out your router. You do not need some big fancy router or that. This is
literally just a cheap little a Zito one that you get from Bunnings and you just need two
different routers. So you've got this one here where the bearing is on the top with the router
part underneath and this one here is all around bearings on the bottom, router on top. So you use
this one first and the idea is this bearing here you just need to have that as a guide so it's
hitting the template and then this is cutting down into the timber. After you've done that one
side then you flip your template to the other side, route that. Once you've done that then you
can just use this piece and go all the way along the entire thing from the other side. So the
knee bearings are sitting on the timber that you just cut. It's a definite rocket science thing
of that but it gives you a pretty good finish. It's pretty accurate. As long as you just take
your time, go nice and slow and you'll get a really nice, good, nice and square. It'll be, it'll turn out
pretty nice. Very fast, easy way to do it. So I'm just basically going to get into that and go to the next step.
All right, there you go. All rounded up and there you go. You've basically got a pretty accurate bow.
Now after this I usually then put it into my vice and I'll grab my square and just go over
it all and just make sure it all looks pretty good. Which it's extremely, it's so close it's ridiculous
that you can't even just use your square as like a bit of a scraper.
You can actually use your square as a bit of a scraper. The other thing to do if you want to make it
absolutely perfect and give it a bit of a sand and everything and all that, you can either put
a bit of like plaster on there like you do use by patching up your walls basically. That just
smoothens everything out and you just, you can even wrap a little piece of sandpaper around that
and just go over that nicely a few times. That'll basically make it perfect. You can put a little
bit of builder's bog on there. Say you did gouge a little bit with the routing, you know stuff
something up a little bit, you twisted something or whatever, you end up with a bit of a ding there,
don't worry just fill it up. You can make make another form if you wanted to, otherwise just
fill it up and either round it back over again or you know sand it down as best you can. It just
depends you know how perfect you want to be. If it's your first time having a crack in a bow like
who cares too much you know, as long as it turns out all right. So there you go, just give it all a bit
of sand, make it nice and the other thing I do is I just screw another piece of timber to the bottom.
That's just length ways so then it stops the bow, I mean this form overdoing this
just to help it. I mean this is solid, that's yeah 40mm thick of
yellow tongue so I mean it's pretty strong. The next thing to do is we need to put a whole
bunch of big holes through here ready for the rear bar to go through and that's what I strapped to.
So we'll basically, I'll just sort of show you the end product really because there's not much
more to do now except put a piece of timber on the bottom and drill a few holes, pretty basic really
and then just a bit of a tidy up. So I'll just sort of show you the end product and then see how I'm
going for tiling the next couple weeks of work I think but otherwise we'll be making our first
recurve out of this form and we'll sort of see how it turns out. All right and basically the last
piece of the puzzle so you basically made your form, pretty happy with it, make sure everything looks
really nice and square and again yeah if you've done any sort of little lumpy do's or anything
like that just bog it out and smooth everything out. Either run your router back over it or
you know if it's just a tiny little thing you can do it by eye and it'll be pretty much close enough
and then yeah I just use pizzeria, you need something very strong don't try and use something
else, you definitely need a solid steel or you need something that doesn't take a lot of pressure
I'm surprised how much force goes in this I've hung mine up to around that 60-65 psi
when I put my air hose on and there's a lot of pressure you know it's it's quite a substantial
amount of pressure that you're putting on your bow. Now as far as making a hose goes
just so I can sort of show you how I make mine this so you literally just go to your local
um what are they called a um irrigation shop uh like we've got a pump place downtown or whatever
but um go to an irrigation place you can usually buy this hose it's not the two inch 50 mil
lay flat hose um you buy it per meter so you just buy whatever you need for your bow plus some
uh so you want it roughly at least and that two and a half meters of the thing so basically buy
three meters of hose and then you buy these fittings these are camlock fittings
but they're actually a plastic so they've got a barbed fitting on one end and it goes into
the male side and then you buy the female female end um has a rubber seal in it so it
does seal up pretty good um when you attach your hose to this again you need to be extremely
like be super anal about it it has to be really good um it takes almost nothing like 60 psi
puts a lot of pressure on things if this comes out at 60 psi comes out it'll be
pretty nuts um so you do not want this thing popping off
so buy a couple good quality hose clamps i actually sikaflex everything inside as well
go buy a good quality one tube of sikaflex basically the same stuff you use like you
know doing a screen in your car or something um sikaflex it all up put it all on clamp it down
almost all the way let it seal up let it hang out leave it give it a few days just go completely
out of control and then tighten those hose clamps up nice and tight and then tape it all up just do
whatever you know just make sure it's mint um and the same is sealing up same sort of thing
and then you can just go down to your local tie shop and grab a valve uh they'll usually just
give it to you uh and then you know you're drilling out like a whatever is 10 mil hole
or something like that and these just pop in this side here's just got the flat cap of the bum
uh and then just test it pump it up to 60 psi leave it keep coming back testing it testing
and testing it make sure it's holding the pressure um and then stick it in your form
do it a few times um i can't stress that enough there's nothing worse than your hose letting go
or something happening when you've got glue on otherwise that's it the bow's stuff basically
because everything goes off too quick the time you sort anything out that's it it's gone and
it's stuck um so just do a couple of dry run make sure things fit good make sure you like everything
um other than that that's pretty much it as you and then when you
sorry so this ends up going across i don't know if this hose should be wrong after this part
yeah um that goes across like that and then what you're doing is i just grabbed your normal straps
so you get your bar that's going in there i literally stick that on and then i'm going over
make sure it's wrapped around make sure everything's really tight wrap it around
nice and tight this and then i sort of do like an x pattern and then go across x pattern across x
pattern across and then i'll make my way back and i'll use another strap and then i'll go the
opposite way of everything um and again you strap everything down nice and tight
um when i'm doing this build i'll probably we'll just do a quick um show you how to glue one up
otherwise i've actually got other videos there anywhere for making bows you can sort of see that
process anyway um so that's pretty much it and then you just come up with the riser design
when i do my risers again you'll see that in one of the other videos but i actually put my
block of timber on the riser and clamp it on then you're tracing the riser so it's perfect
and it makes it just a lot faster you literally just banter on it out and then just set it down
to that line right on that line and it's basically perfect um you might just need
to do a couple little tweaks but you want the riser fitting that basically perfect
um that's about it i hope you like that one just a quick video so as you can see it doesn't really
take long um it's not hard doesn't take long to whip up a form and have a go at making a bow yourself
the hardest thing out of the whole bow making stuff is well for one kind of design actually
works but it's actually tapering um tapering your cores that's actually the hardest part
um i'll show you how to do mine there's a four or five hundred dollar sander that i use um you
can actually use a drum sander on your um jewel press which will also work just takes longer um
it doesn't take a whole lot to make you know something that's just half decent
make yourself a bow um so really it doesn't take a whole lot order some glass from
one of the places in america i don't think there's anywhere really in australia that sells the glass
really anymore um you're better off just buying something from america which sort of sucks a bit
otherwise you can hit one of the other australian manufacturers up like myself
or one of our followers see if they've got puppets of glass if you want to have a cracker
that i'll sell you um that's about it so yeah well um next video i might even just show you
me making this one um but otherwise we'll catch you on the next video hope you enjoy this one
cheers
