In this video, Randy covers the four essential functions of a hitch system: connection, weight distribution, sway control, and safety. Here is a summary of the key points and tips shared:
Key Components of the Hitch System Weight Distribution: Using torsion bars (in this case, 10,000-pound springs) to ensure the tongue weight is distributed evenly across all axles of the tow vehicle and trailer. Sway Control: Using an equalizer hitch system that relies on friction points on the torsion bars to prevent the trailer from swaying due to wind or passing vehicles. Safety Features: This includes safety chains and a breakaway cable that applies the trailer's brakes if it ever becomes uncoupled. Step-by-Step Hitching Process Pre-Hitch Prep: Ensure stabilizer jacks are raised and wheels are chocked so the trailer doesn't move. Receiver Setup: Slide the receiver into the truck's hitch and secure it with a pin and clevis pin. Alignment: Use a backup camera if available to align the ball with the trailer coupler. Coupling: Lower the tongue jack until the coupler is over the ball, then lock the latch. Weight Distribution Bars: Raise the trailer and truck slightly using the jack to make it easier to slide the torsion bars into place. Final Connections: Safety Chains: Cross the chains under the tongue (to catch it if it drops) and hook them from the top. Breakaway Cable: Attach it to the tow vehicle at a length that would trigger the brakes before the chains reach their limit. Power Cord: Plug in the 7-way power connection (Randy uses bungees to ensure it stays securely engaged). Actionable Tips for Creators Maintenance: Regularly inspect your equipment. Randy highlights replacing rusty clevis pins as a crucial safety measure. Lubrication: Keep the hitch ball and certain friction points lubricated to reduce wear, though Randy notes some systems require friction for sway control, so check your specific hitch manual.
*********** CAMERA GEAR ********************* Our Complete Camera Setup: Go to Camera - DJI Osmo Pocket 3 Dash Camera - BlackVue DR770 Still & Video Camera - Sony A7C Sound - DJI Mic 2 Flying Camera - Mavic Mini 4 Pro
ZEPHYR TRAVELS All Rights Reserved *This channel for entertainment purposes only. We are not RV or travel experts. We share our opinions and what works for us, but you should do your own research.
00:00 Introduction 00:59 Raising the Trailer 03:09 Receiver hitch 05:43 Backing Up 10:03 Safety Chains 12:05 Weight Distribution Bars 16:54 Pluging in the 7 way wiring 18:25 Brake-A-Way Cable 23:47 Final Thoughts
AI Generated·May contain errors
Video Summary
AI Generated
Randy provides a comprehensive tutorial on the safe and correct procedure for hitching a trailer to a truck. The guide emphasizes a systematic approach, focusing on mechanical alignment, the installation of safety components, and the critical importance of electrical and emergency braking connections to ensure stability and safety during transit.
Hi everybody. Welcome back to Zephyr Travels. I'm Randy. And I'm Diane. And in this video,
we're going to teach Diane how to properly hitch up the trailer. I think it's important that you
know how to do this because if something happened to me and I wasn't able to hitch it up and you
needed to move it or whatever, you know, you should be able to do that. Right. And it's also
important that Diane is able to walk by the hitch and notice if anything's wrong in case I make a
mistake. Because you're walking back and forth. When we get ready to go, glance over, double
check me. That's true. It's a good idea. Yep. So I don't expect you to hitch the trail up every
time, but I think the basics are really important. So we're going to get into that next, right after
this. So I have set everything up just like we're at a campsite. So before you do anything,
you've got to make sure that the stabilizers are up and that the wheels are blocked, which they are
because you would do that when you unhitch, and that the X-chalks are removed from the wheels.
So I've got that set up. So we'll go over and do that next. Okay. The first thing we're going to
do is the stabilizers jacks. And so this tool is usually in our compartment and it's just a matter
of plugging it in and cranking it up. And I usually like to just make sure those are flat
to the bottom of the trailer. So I just tip it a little bit with a wrench
and, you know, so it gets to the top and it's tight. Now this is the, this what I happen to
call the T-chalk or they also call it X-chalk. It goes between your wheels. I don't always put
this in place, but when I do, it's because we're there for a while and it takes some of the bounce
out of the trailer. Okay. Some people use these instead of chalking your wheels like this,
but the manufacturer does not recommend that. They recommend to only use this
to take the bounce out. You always have wheel chalks like this. Okay. So this
uses a wrench here and you just loosen it. And there's one way or the other,
there's like a loosen side and a tighten side. Unfortunately, it doesn't say that on here,
but if I do it like this way and I go to loosen it, it works. It doesn't do anything.
Yeah. If I go to the wrong way, it's going to try to tighten it. Okay. So just loosen it a little
bit. Pull it out. Pull it out. Okay. Okay. That's all we need to do here. Okay. To put the receiver
on, it's usually on the side or something. This is pretty heavy. There is a handle on it. You
just try lifting up. Be careful of it. That's the greasy part right there. That's the ball.
Just pull up on the handle. Oh my God. So you would definitely need to get help. I don't want
you to do it. I don't want you to hurt yourself. All right. How much does that thing weigh? I bet
you 50 pounds. Probably weighs as much as Lincoln. Oh my God. So to put it in, lift it up,
grab it back here. This is where you definitely want to have gloves or whatever.
Slide it in until you get to the end of the rusty part. And then this pin slides through
like that. And then the clevis goes in the hole on it. Okay. Like that. Yeah. I definitely would
need help. Yeah. You would definitely want, you know, if you got to this point, you would
definitely ask for some help to get that on or maybe I left it in. So now we're ready to raise
the trailer. We've lifted up the jacks. We've take the X-Chalk out between the wheels. You want
to make sure your door is closed on the trailer because it does put some twisting flexing on
there and you want to make sure that's okay. Is door closed? Should be. Door is closed. Right.
And you want to make sure that, you know, if we're in a situation where up and down may actually
lower the front quite a bit, you'd want to make sure the step was up. Okay. So we don't have to
do it for this, but it is down right now, but we would make sure that the step was up. So this
up to go up, switch down to go down. Okay. So we want to raise it up. So it's off the boards?
It's going to stay on the boards. Okay. What we want to do is... Go all the way up? We want to go
so it's high. This is higher than the ball so the ball can go underneath it. Okay. You know,
highest it will go? There is a maximum height. I think you're just a little bit more.
Okay. Stop there. What we'll do is we'll back up a little bit and check. Okay. Before we go
underneath. But I think we're good. Okay. Okay. So now we're going to go inside the truck. The
truck. And then we'll put you in the passenger side. I'll back it up. Okay. We're not going to
get into a whole backing up lesson here. Right. But we'll show you how I use the camera and how
I back it up solo. So we'll do that next. Okay. Okay. So when you go into reverse,
the backup camera will come up, right? Right. Now this is the far view. You hit the plus
and it zooms in. So now you can see the ball and you can see the hitch and there's actually a
dotted line lining the two up. Oh, okay. So you want to go back very slowly. Uh-huh. And I'm a
little bit off. See, I'm to the left side of the ball, the hitch. Right. So I'm turning it a little
bit. Turn my wheels to the right. Now I'm kind of lined up. I'm going to go straight. Okay. Now
at this point, I'm going to check because I think I'm hitting. Okay. We'll just go quick. Check
outside. Okay. So we're actually really close. Yeah. So we can, we can do it. We don't have to
go up anymore. So you wouldn't want to go up anymore. You wouldn't. We could. It doesn't
matter if you're a little bit higher, but we're just a little, we're just close. So this looked.
Okay. So when you go back into reverse, hit it again, hit it again, and it zooms in. Okay. Now
one thing with this truck, every time when you're in this mode, when you're in this
highlighted, you know, hitching mode, the truck will automatically put the parking brake on every
time you put it in park. So I'm going to take, so I have to make sure to take the parking brake off.
It's also a good idea that you do that. If your truck doesn't automatically put it in park,
you want to, because the truck will roll a little bit when you put it in park.
So you want the brake to be on. Okay. So I'm going to go just a little bit.
I think that's perfect. We'll have to go out and check. Okay. You see now the truck just went in
the park. Okay. Does it come with the trailer package? What's that? Does it automatically put
the parking brake because you have the trailer package? Yes, it does. It is part of that package.
Okay. Okay. So now if you look down here, we are, still need to go back just a tiny bit.
Oh, really? See, here's, look at the edge of this, compare it to here. Oh, right. And we're
about a half inch off. Okay. So not much. Right. Okay. So I got to take the brake off. Right.
You got to press the zoom and I'm in reverse and I'm just going to go that much. Okay. Barely
release the brake. And what do you see? Now you're a little too far back. Right. This is normal. I
mean, don't think that y'all, this is normal. You're going to, a lot of times you're going to
have to go back and forth just a little bit to get it right. It's just, it's fine adjustments,
but you'll get there and you can be slightly forward of the ball, but you can't be behind
it because there's a lever back here that locks into it. You don't want to drop it down on that.
Right. But if you're slightly forward, things will pull themselves together because it's rounded and
or just slide on. Oh, okay. So you just have to pull ahead just ever so. Yeah. So I'm going to
have you stand here. Okay. And you're going to tell me that we're good and I'll pull it forward.
Okay. Brake off. Okay. Now go back a little. Go back a little. Okay. Okay. No, no, no. Go forward.
Too much? Go forward. Now you're going to go down. You make sure that this is up.
Okay. This slides forward and then pivots up. All right. Which? The one closest to you. Push it down.
Right there. So as soon as you hear it hit? Yep. Okay. Now, two things you want to do.
That goes down. That locks it to the ball. Okay. You also want to do your safety change at this point.
So there's a little lever on the side here. Yep. Now they go, if you notice,
the chains are crossed. Right. That's required. Okay. And then on each side of the hitch,
there's a spot to hook it. Now, let's talk about safety chains a little bit.
There's a couple rules. One, they have to be a certain distance off the ground. They can't
drag on the ground. Oh, right. That makes sense. Because they will spark and cause a fire. Okay.
Now, we do have chain socks, which we got from Love Subbing, which will help prevent that.
And it also keeps them covered and looking good. Right. Now, I talked a little bit about
the safety chains, the length. If your chains are too long, you can shorten them. There's a pin here.
You can take that out and move it to a different link and shorten them up if you need to.
You never want to twist them. Some people will take their chains because they're too long and
they will turn them like this. That puts them on tension and actually weakens the chain.
So you never want to do that. Like I said, you want one twist in here. And basically what this
does is this creates a cradle. So if the trailer becomes unhitched, hopefully it lands on this
and not drags on the ground. I see. Okay. The next part on this is different by manufacturer.
And there's a number of different types of hitches out there. And so the theory is pretty much the
same, but how it actually works may be different for different people. So these are the weight
distribution bars. Oh, these are heavy too. Yes. These are our spring. So these are designed to
flex. And there's a pin. You can see you have your pin still attached right there. Right.
So you got to take the... Pull the pin out. Yeah. Pull the clevis. This is called a clevis. Pull
that out. Okay. And then take the pin out. Yeah. Okay. Now you can see there's a square spot right
there. Should slide right into that. Does it matter which? Yes. Now you had it the first
time like that. It should slide all the way in. Okay. Now that pin goes back in. Okay. And this
goes into the little hole. Just to the middle there? Yep. That's fine. Okay. So hold that for me.
So this just slides in. I always put the pin from the outside in like you did. Okay.
That way this is on the inside so it's less likely to be knocked off.
Oh, right. And you can... You have in the middle. You can also put it all the way through. It really
doesn't make a difference. In fact, it might actually be better attached all the way if you
click it all the way through into the loop. Okay. Less likely to get knocked off. Okay.
All right. So now we've got these on. These go here. Step over. So these ride up on here.
And this pin holds it in place. Some trailers have a chain here that you have to attach.
But actually we happen to be just high enough that we could slide it on here. If we weren't,
we just raise the trailer up a little bit more. Okay. And this just drops in like that. This
comes down and holds this pin in place. This allows this bar to slide back and forth, which
gives you our sway control because this is metal on metal. You never grease this. And that resistance
prevents the trailer from swaying. If you have a problem and you can't get it high enough,
they give you a tool. This little guy right here. So you can take that, put it in the hole,
put this here. And raise it up. Yep. And it's really easy. That locks that in place.
I'm going to do the one on the other side. Now you can do your side. Yep.
Sometimes I think we're going to have to raise it up on this one.
And that's not uncommon because the trailer and the truck may be twisted a little bit.
Oh, okay. So jack it up. More? A little bit more. Nope, a little bit more.
There you go. And the pin is right here. Drop that in. Fold that down. Okay. Now that we've got
those on, safety chains are on. What about this? That's, I do that last. Okay. Diane's talking
about this pin. This pin that goes here. You can put it in now, but I'll show you why I do it last.
So now we want to take the weight off the jack. Raise it? Nope, we're going to go down. So it
starts coming off the ground and even after it comes off the ground. Okay, stop for just a minute.
Okay. See right here, there's like where a piece of tape was. It's kind of worn down. That's the
point you want to stop at or sooner to this. So you've only got maybe two more inches. So keep
going up. Before that? Stop. That's perfect. It's up out of the way. It's tucked out of the way.
It's not going to drag on the ground. Right. It's not too far because if you go all the way up to
the point where this bottoms out, you'll blow the fuse. Oh. And then the jack won't work. Okay.
So that's done. So now what we have left is our power cables. Our seven-way cable and our break,
our breakaway cable. Okay. So let's do the power cables. They're pretty straightforward.
So most trucks have one of these already on their bumper someplace. There's a square edge
here like a pin. It's round and it's got a little pin on it or tab that matches in here.
Goes in like that and then this comes out and locks on here. That tells you it's locked in
place and tight. Okay. We also have a second cable. This only does, this only works for the
pro backup. So once this is connected, the truck knows what position the trailer is in.
So if you use the pro backup, it will steer the trailer for you automatically and you don't have
to mess trying to turn the steering wheel backwards and such. Okay. So I don't use that a
lot, but I always hook it up and that just goes in and locks in with a cap going on the bottom.
This is the breakaway switch. So right here, there is a switch and a pin and you pull this pin out
and the brakes will automatically lock up on the trailer. They're electric brakes. They draw power
off the batteries in the trailer when this happens. And if this pin is out,
15 minutes is all you've got of usable brakes and the brake system will burn out.
But it's all you need for emergency. But the reason I tell you that is this is not a parking
brake. It's an emergency brake for just a quick moment. It's going to stop the trailer if it
becomes disconnected from the truck. That's the point of it. Okay. If it comes completely
disconnected on this, the trailer brakes are going to lock up. And it's not going to be like
lightly putting on the brakes. They're going to lock. This trailer will come to a screeching halt.
Keeps it from running away or whatever. So it's important to know where you hook this.
The ideal is that you're trying to safeguard this whole setup if something here fails.
The most likely failure would be it comes off the ball. You didn't lock this down or whatever. You
hit a bump. It's bounced up. Truck went forward. This came down. But any part of this could fail,
including the part attached to the truck. So you don't want to attach this to any of the hitch.
Some people will attach these. I've known people that take them and loop them around the ball
as an attachment point. A lot of people will attach them down here where we put the safety
chains. You don't want to do that. You want this to be simply separate. So you find a hole on the
frame of the truck. I'm going to do what I did. I got this from Rich Collins where he put a loop
on his license plate bolt and he attaches it to here. Now he does it a little bit different. He
uses a little quick connect here. But I look at this and I go, this is a lot of cable left over.
Which basically means all this cable has to be stretched out before the brakes go on.
And if it came off the ball, remember I said that was probably the most likely way it's going to
disconnect? Uh-huh. The safety chains are going to be there. Right. So what's going to happen is
this trailer is going to get loose. It's not going to have any brakes. I mean it's not going to be
connected to the truck. So when you step on the brakes of the truck, what's going to stop the
trailer is the truck. So this is going to go crashing into the truck. And the bumper is going
to stop it. So you'd like to avoid that. Also there's going to be that incident between this
actually coming off and you reacting to it. I mean yeah your brakes are still connected here,
but you're going to have that incident. By that time it's probably going to crash into your truck
or they're not going to be sequenced or whatever. So I loop it through here and I bring it back
and put it on this pin. That's why I didn't put the pin in earlier. Okay. So now you can see this
isn't that long. Right. If it comes loose, hopefully this pin will come out while it's
still on the safety chains. The trailer will stop. It will start stopping the truck and it will keep
the two apart and allow you to get off the road safely. You want to make sure there's nothing in
the way. This is a straight line so that this pin comes right out. You don't want to tangle it up
like around this or you know it's not going to work. Right. In fact, when we bought our trailer,
the technician at the dealership took this cable and wrapped it around the safety chain. Oh. It
would have never worked. Yeah. You know, unless the safety chain broke, this would have never
worked. Oh. Okay. So this is completely independent. And like I said, I like it here.
I think this is one thing that most people never do. Right. And now I know this will stop it.
The next thing I do is you want these things to make sure that they never get pinched and
they're out of the way. So I cook them right here. Now they're in the center of the trailer.
So when the trailer turns, they're not anywhere near this turning part. So it's not going to
get pinched. So I know that these are safe. These aren't going to get damaged. They're out
of the way of the cable here. All makes sense. Sure. You're all hitched. Yeah. Yeah. Except
for lifting the hitch itself, it seems pretty straightforward. Yeah. I mean, when you do this
all the time, there's not a lot of steps to it. Right. And you can have a checklist if you want.
But it's not a lot of steps to this. You can do this fairly quickly. And, you know, you do it the
same way every time. Try not to let anyone interrupt you while you're doing it, because
that's when you forget things. Right. And then when you're done, just give it a good visual check.
Make sure all your pins are on your weight distribution bars. This is on top of the ball
that this is locked in place. Your wires are in place. Your safety chains are in place. So
what'd you learn? How to hitch up the trailer. Right. All the steps involved. It didn't seem
other than me lifting the hitch itself, which I'm sure I could get somebody to assist me with.
If you had, you know, you. I probably could if I really. You're going to just get greasy. I
didn't want you to get greasy doing it today. Right. Make sure you have a pair of gloves. Yeah,
it's probably a good point. I don't always have gloves on when I do this. Yeah. Yeah. It helps,
you know, saves the nails on us women and prevents your hands from getting all greasy. Right. Well,
if you like this video and you learned something, please give it a big thumbs up and subscribe to
our channel Zephyr Travels. And if you haven't already, what did I already say? Oh, press that
hype button. It's still available. Yes. And if you haven't already subscribed to our channel,
although I may have said that already, but in any event, yeah, it really helps us out a lot. Right.
Hit that bell for notification. Yeah. Leave us a comment. Did you hit your trailer up differently?
Did we show you something that you haven't seen before? Let us know how we did. And if we, if
there's something we're missing that we should be doing, leave it in the comments and put a link in
the description to how to get your own set of chain socks from Love Selling. Yeah. Until the
next time everybody. See everybody down the road. Take care. Take care. Bye.