Whittle a Simple 1x1 Eagle | Step-By-Step Beginner Tutorial

Eternal Sculptures
211 followers
The Maker Experience guides beginners through a step-by-step process of sculpting a stylized eagle from a simple block of wood. Using a sloyd knife, the project covers techniques like rounding edges, shaping the beak, and adding feather textures with V-cuts. #gjwart #art #sculpture #clay #statue #bronze #wood #sculpturing #woodworking #woodcarving #woodcraftsman #clayart #claymodeling
AI Generated·May contain errors
Video Summary
AI GeneratedThis tutorial provides a step-by-step guide to carving a simple eagle from a block of wood. It covers the entire process from initial proportions and rough shaping to detailed carving of the head, wings, and feet, emphasizing balance and the use of various cutting techniques to achieve a realistic bird silhouette.
Today we're making a simple one by one eagle. We're going to start this project by
rounding three of these long edges and that can be done with rough cuts.
Something like that is good enough for now. Next we're going to divide this length in four
and then this way we're going to divide this block in three. Now from this point over here on the top
we're going to draw a curve that goes pretty much all the way here and then it goes back
to this line on the bottom. The thickest part or the highest point of this curve should be about
here on this line. So that's where this curve reaches the furthest that way and then we can
remove all of this excess wood. So this line is the border over here and then this curve
marks where the back is going to be. So I can make just a few sweeping cuts over here
and then a little bit of finishing with smaller push cuts to get that curve nice and round.
Next we can mark the halfway point of this bottom quarter and draw a straight line from here to this
corner and we can do the same thing on the other side and now we're removing this bit of wood.
I think this is easiest to do starting off with a few sweeping cuts then I'm moving on to rough
cuts and push cuts. You can even use a saw for this and some sandpaper if you want a perfect
flat finish. This is going to be the bottom of the bird. Now this can barely stay upright like this
but the balance is going to get better once we work on this part and that's what we're going to
do next. So over here in this square I'm dividing this area in three and then I'm dividing this
one third in half. Now over here we have the corner between the body and the feet. So all of this
can be taken away but then we're leaving some wood over here and that can be done with stop cuts
like that and then the remaining piece is easy to take away with rough cuts and some push cuts.
Now this right here, the top quarter, is more than enough space we're going to need for the head.
So this way we're not going to touch it yet but this way it's obviously too thick. We're only
going to need about one third of this thickness. So I'm dividing this in three and then starting
from this line I can extend it to the other side to make this a little bit easier. We're making some
sweeping cuts. Something like that is good enough for now. Next we're going to work on this bottom
part a little bit. So we want the body shape of this eagle to be a little bit more like a water
droplet shape instead of this blocky shape that is right now and the thickest part is going to be
here on this middle line. So I'm just drawing these two curves on the sides to help with
perceiving the shape before making the cuts and then I'm just making some rough cuts to remove
some thickness from the sides. That's pretty good. Next I'm going to turn this face on this top
quarter into a single edge and from above it's going to look something like this. Just a triangular
shape and again I can make some sweeping cuts so that this edge will only appear on this top
quarter since we want this to have a lot more mass. Next we're going to make a basic shape for the head
and that I'm going to start wanting to be like a hook shape like that. This is the underside and
there's a straight line like that and then a curve where the neck is going to meet the chest and then
here on the top side of the neck we're making this corner round and then here on the back of
the head that corner is also going to be round. Something like that and over here I'm making a
stop cut but it's going to be in an angle and with this it's important not to press the blade
too deep into the wood because the deeper you press the harder you're going to have to press
which means that it's easier to chip off this entire thing. So just a little bit at a time
and then we can make some sweeping cut motions over here. Something like that is good enough for
now. Next we're creating a v-shape here on the back so just something like this and then with
a few sweeping cuts we can remove these lines that we just made. This I think is actually one of the
biggest benefits of a Sloyd knife because with this rounder edge I can reach inward creating
dents like this. Now don't worry if you have a straight edge on your blade you can just make
this as a like a two-sided stop cut so you cut here you cut here and then you just create a flat
surface. Before we go any further we can do some rounding so we can take away all of these
unnecessary sharp edges. We're not going to touch this yet or this but everything else can be made
a little bit rounder and the most important cut for this step is this very shallow push cut.
Next we're going to carve the wings and from the front here there are just going to be two lines
like this. Be sure to leave a lot of space here in the middle for the chest so the wings are here
on the sides they don't come here close to the center and then these lines curve all the way
very close to the bottom here because the wings of an eagle almost reach as far down as the tail.
This part right here can be a little bit more straight so below this corner it can be pretty
much like a straight line and then over here we have that curvature. Yep that's better and then
we're going to carve this with some stop cuts so you can press the blade into the wood along the
line like this and then we can cut towards the line. Now here on the tail I think it makes sense
to make a few sweeping cuts first because it's safer. Now we have this corner here that can be
cleaned with these stop cuts. Notice here that I'm not cutting from all the way down here because we
want to leave as much mass over here on the bottom as possible. That's going to be the stand for the
eagle and if it has too little mass the eagle is going to tip over. Then over here on the top I think
these kinds of v-cuts are easier like that. So from one side cutting with the tip of the blade
and from the other cutting with the long edge of the blade and then we can make these edges on the
side of the body a little bit rounder. Then up here with a few sweeping cuts we can connect
this v-cut smoothly into these already existing sweeping cuts. Then we're going to make the edges
of the tail so the line we're going to draw starts from about the middle of this part of the wing.
So measuring from this corner all the way over here about in the middle of this section of the
wing and then we go down with a slight angle same over here. That's good. Next we're going to make
the feet. I reserved a little more space over here so that we can adjust the proportions but now
we're going to need to take this slightly further down. Starting from the top of the wings I'm going
to divide this eagle in three parts and over here on the lowest third line is where I think the feet
should be. Looks about right. So I'm going to move this line a bit further down. I'm also bringing
this lower part of the stomach further in. That way we can keep this eagle a little bit more top
heavy the way it's supposed to be. So the stomach curves in like that and then the feet are going to
start pretty much from the edges of the wings. Now we can work on this edge. We don't want to
take away this corner because that's the furthest away point on the bottom over here and if I just
make this round the eagle is probably not going to stay in balance. So instead I'm going to do something
like this. I'm making this edge straight and the parts below it a little bit round. Something like
that. And then I'm making this edge rounder so that it's closer to the shape of curving toes
like that and then I can make a little distinction between the feet and the piece of wood that the
eagle is sitting on. Next I'm going to make a v-cut here in the middle. Just something like that
and then two more v-cuts per side to separate the toes from each other. Then over here I'll need to
take away some of this mass from the side of the last toe by creating this two-sided stop cut
like that. And then to make the shape of the toes a little bit nicer I'm making the toes pointy
and this just takes a few very small stop cuts. Now I'm also going to make a v-cut over here
to separate the wings from each other a little bit. Over here there's no need to do that but
somewhere here a small v-cut adds a little bit of nice detail. And a few of these longer push cuts
will add kind of like a feather pattern on the wings. I think it's a nice detail that makes a
surprisingly big difference. And then above those longer cuts we can make a few medium-sized cuts
before the texture fades in to the smoother parts of the back. Here I'm just adding a feather pattern
on the edge of the tail with a few very small v-cuts. Next we're going to work on the head
shape a little bit and we're going to start with this curve. So we want to create a distinction
between the beak and the head and we can do that with a few sweeping cuts like that.
Then we can make the beak a little bit smoother and we can turn those sweeping cuts into v-cuts
and a few more v-cuts over here to create this sharp corner over here. And then a couple
sweeping cuts can be used to create that hook shape on the underside of the beak. Then I'm making
two v-cuts. I'm extending this corner of the beak slightly further back for a little bit more of a
realistic beak shape. And now it's time for the final adjustments. If you feel like there's still
some proportional issues that need to be fixed, I'm taking away a little bit of this mass from
the back of the head making some areas slightly smoother. You can also add a little bit of texture
to the piece of wood that the eagle is sitting on if you want. And then that's it for the project.
One more detail actually and that's this small triangular shape that we're going to make.
