SLF Automatic Pressure Blast Unit for the Treatment of Planetary Gear Carriers , Commercial Vehicles
AI Generated·May contain errors
Video Summary
AI GeneratedThis video demonstrates an automatic pressure blasting unit featuring a robotic loading system designed for cleaning and hardening planetary gear carriers. The system integrates noise protection, precise SPS control, and an automated abrasive recycling process to remove weld spatter and induce compressive stress in gear components with high reliability and efficiency.
Comments are disabled for this video.
We have previously built different kinds of blast systems used to clean, deburr and harden gear wheels at the ZF company in Friedrichshafen.
Today we have the opportunity to view a test run of an automatic pressure blasting unit with a robotic loading system at our own plant.
This system was completely enclosed in a noise protection enclosure equipped with sealing elements.
The soundproof walls have two access doors and two inspection windows on the front and right side of the enclosure.
With a blasting pressure of 5 bar, the sound pressure level outside the housing can be reduced to less than 75 dBA.
The SPS control system of the unit is designed for 100 blasting programs.
The mobile operator panel is very helpful when setting up parameters for new workpieces.
The appropriate workpiece types are first manually selected using the inputs for the blasting process and the robot control system.
A roller table is used to separate and feed the workpieces to the robotic loading system.
The blasting process used here to treat so-called planetary gear carriers is as follows.
After the automated welding process is complete, loose weld spatter adhering to the interior surfaces of the parallel flanges must be removed.
In addition, a residual compressive stress must be induced into the splines of the planetary gear shaft.
Once the workpiece has been automatically placed on the cabin's indexing table and once the indexing table has advanced by one position, the entry and exit doors in the front of the cabin close.
The loading system can handle workpieces 220 mm in size with weights up to 30 kg.
The walls and doors of the blasting cabin have rubber anti-wearing linings with a thickness of 10 or 20 mm.
A rotating hold-down device is now lowered vertically from above and onto the satellite table, which is in the blasting position.
This seals off the upper surface of the workpieces.
The blasting process, which uses four pressure-blasting nozzles, can now begin.
A vertical nozzle manipulator, which is driven along a linear guide by a servo motor, is used to move the blast nozzles.
The four blast nozzles are first used to blast the area between the discs of the planetary gear carriers, which frees them of scale and loose weld spatter.
Once blasting is done, as a rule this takes about 120 seconds, the blasting nozzles shut down and the hold-down device retracts upward.
In the case of some workpieces, there is an area that must be additionally hardened.
To accomplish this, two nozzles pointed vertically at the shaft are used to blast these areas, including, for example, splines on the shaft.
And this creates a residual compressive stress of 0.2 Alman.
The indexing table advances to the next position.
There, the workpieces are blown off with compressed air.
In the third phase of the process, the satellite table advances yet again by one position and a gripper removes the workpiece.
The robot subsequently stops the workpieces in a separate blow-off cabin.
A sealing plate located on the gripper arm automatically closes off the cabin.
Once in this position, the workpieces are automatically rotated in both directions so that the blow-off nozzles can reliably empty all of the scoop-like spaces in which materials can collect.
The robot then places the workpiece on the customer's conveyor system so that it can be fed to a downstream labelling device.
A screw conveyor transports the abrasive collected in the cabin hopper to a bucket elevator.
The abrasive is fed to an abrasive processing station on the roof of the unit, where a cascaded air separator subsequently processes the abrasive.
A uniformly thin veil of abrasive is created with the help of a cone and the fine material is extracted from the veil of abrasive.
The cleaned abrasive falls into the silo below, where it's stored for the ongoing process.
The 200 litre pressure pot is mounted beneath this 500 litre storage silo.
A precision feed mechanism controls the transport of the abrasive medium to the blasting nozzles.
A control system with adjustable sensitivity monitors the flow of abrasive and guarantees reproducible results.
The dust-laden air from the air separator and the cabin is extracted using a cartridge filter system with a volume flow of 2,400 cubic metres an hour.
The filter unit removes the fine dust.
Using the associated control system, the cartridges themselves are cleaned using cleaning impulses,
whose predefined intervals determine the time and intensity with which the filter elements are cleaned,
so that the unit can be adjusted on a case-by-case basis to the blasting conditions and dust load.
This ensures a highly efficient cleaning process, as well as a high level of availability and a long service life for the filter elements.
A rotary valve discharges the dust into a waste collection sack.
By carefully coordinating the operation of all components,
we provide you with a system that delivers excellent results and a high level of reliability.
SLF – your partner for blasting, coating and conveying systems.

