Stopping REAL FIRES with LEGO

The Story of Lego
1 follower
37 Video Views·May 14, 2026
I used different Lego cars and machines to stop bigger and bigger fires…
AI Generated·May contain errors
This Lego fire truck is on its way to an actual Lego fire.
But no matter what I do with these pieces,
the fire is not getting put out.
So I'll fix that by building more and more
complicated machines to put out harder and harder fires.
Like first, this Lego fan car
that will hopefully blow out the fire.
So I can drive up to it and,
which easily puts out the fire.
So for level two, I'll add this big dumpster
that blocks the air flow.
But it still manages to blow it out.
So for level three,
what if the dumpster still has a roof on it?
Well, we finally found its weakness.
So next I'm gonna build a sort of car thing
that drives over the dumpster and can dump water on top.
I'll use these knob gears to motorize
all four axles of the wheels.
And this turntable can build our foundation for steering.
Then I can connect each wheel section with a chain
that allows me to drive all of them
through one output axle.
Each wheel section also has a differential
to allow for the wheels on each set
to rotate in different directions
when turning with the four wheel steering.
Then to make it actually a firefighting vehicle,
I added a scoop on the front to dump water.
It's a very hard vehicle to steer,
but once I got it in place...
Okay, but what if we have a forest fire over here
and a car fire on the road,
and we have to put out both?
I tilted the bucket the wrong way on the first run
and somehow had a tiny bit of water left over
that I could put out the next one.
But despite autofocus trying to ruin my shot,
you can clearly see there's not enough water left
to put out the second fire.
So I think next, the best option is to go back
and make a better version of the fan car.
We'll motorize the back axle here.
And using this axle, I made a steering setup
that will be controlled by a Lego Servo Power Function motor.
Okay, and with the basic chassis of the car done,
let's test it to make sure everything works like it should.
It steers and drives just fine,
so that should work great for everything we need it to do.
Then once again, I'll add the fan on top
with this super fast motor.
All right, let's try this again.
It easily blew out the first candle.
And unlike last time, we now have the ability to steer,
meaning I can change the angle
and blow out the next candle.
They don't stand a chance against that.
But these candles are way too boring and small of a fire.
So next I got these fire starter cues
that will pose a much larger challenge for the fan.
And no matter how hard I blew on it with the fan,
it just couldn't quite put the fire out.
So next I'm gonna use water in this spray bottle.
And I've cut the tube in the center
because it's gonna go upside down.
But pressing the handle is easy for me,
but for Lego, I think it's gonna struggle.
So I'm gonna add this rubber end here to hopefully help it.
And a second one at the top to lock everything in place.
This cam will be the mechanism
that pushes the actual trigger,
which should hopefully be strong enough
using these worm gears to actually spray water out.
But unfortunately, because of the angle
which the bottle is attached,
it's gonna spray upwards and not onto the fire downwards.
So let me fix that.
And now using these linear actuators,
I can change the angle which pitches it downwards
to hopefully point better at the fire
rather than just straight forwards.
But we're about to find out.
Well, at least it can actually press the trigger
and spray water.
It took a ton of sprays with the water over and over again,
but eventually it actually managed to put out the fires.
There's a few embers, but it's out.
So let's see if it can handle
two of these fire starter bricks.
It looks so cool when the water hits the flame.
But no matter how much I sprayed,
it clearly was not going to put the fire out.
So next I'm gonna make a smothering machine.
These arms will rotate in sync
and hold a wet paper towel
that will hopefully put the fire out.
And now that the paper towel is on,
I can spray it with this water.
And then when it comes down over the fire,
it potentially will smother it.
But I have my doubts.
The first attempt didn't work at all,
but I moved the car slightly forward and lowered it again.
And it seemed to do the trick just fine.
But what about three?
Well, once again,
it had absolutely no problem putting out the flame.
So for the next level,
I tried to make it harder by adding these sticks,
which would hopefully keep the paper towel off of the brick
and stop them from actually smothering the fire
by touching the bricks.
And even though flames were literally spewing out the sides,
it still put a stop to the fire.
I'm honestly very surprised by the success
of the smothering machine,
but I think it just means
that we haven't made the fire big enough.
So let's try 10 fire starters.
I also made them log-shaped and standing upright,
which will hopefully make it too tall for the smother
to actually cover the whole thing.
And besides melting the corners of my Technic beams
on the front of the machine,
I don't think anything actually was achieved
because the fire certainly stays strong.
Let's try using water for real this time.
It's gonna be pretty heavy.
So I made a super strong chassis
with two wheels at the back,
which will be driven by two motors,
hopefully strong enough.
And to top it,
I made this frame with a Lego pump using these splat gears.
The water sucked in from the inlet at the bottom
and then it's routed around the edge of the gears
and pushed out the tube at the top.
And I designed it to perfectly fit this plastic tub.
And surprisingly enough, considering it's Lego,
it actually pushes out water at a pretty good rate.
And when starting at full,
it runs for a decent length of time too.
But the real question,
can it put out this massive fire?
This sizzling might be one of the most satisfying sounds.
It may take a while,
but thanks to the large capacity of the tub on the car,
I have a decent amount of water to go through.
And finally, after about half of the capacity of the water,
it finally put the fire out.
But it's so satisfying,
I had to run the rest of the water through the pump
just because it looks cool.
