This engine may be small, but the failures are often massive. In today's video, I am tearing down of a Smart Fortwo 0.8L 3-cylinder Diesel engine to find out exactly why it ended up on the scrap bin. These tiny powerplants are famous for their engineering—and notorious for their appetite for oil and burnt valves, turbos, and in this case, hydraulic lifters!
I'll strip this motor down to the bare block, inspecting the engine head, the timing set, and the reciprocating assembly to identify why at 300,000km this engine was condemned. Whether you are a DIY mechanic looking for repair tips or just here to see the internal mechanics of one of the smallest production car engines ever made, this deep dive covers it all.
In this video, I'll cover: Initial Inspection: External analysis, common issues and the common rail fuel delivery system The Cylinder Head: Pulling the cam and inspecting the smoking gun: a hydraulic lifter decided to leave the chat! Bottom End Analysis: Checking piston rings, cylinder wall scoring, and bearing wear in and between the diesel oily mess! The Verdict: Final analysis of what caused the failure and if these engines are worth rebuilding. While diesel engines in general are reliable, smart engines take a lot of labor as the car has to be disassembled from underneath to swap them out.
Time stamps:
0:00 - The Smallest Engine Teardown 1:03 - Removing the Injectors and EGR 4:36 - Removing the Valve Cover 6:10 - Front Accessories & Timing Chain 12:36 - Head Bolt Removal & Inspection 13:30 - Piston & Crankshaft Analysis 16:51 - Lubrication System 18:04 - The Final Verdict: Why it Failed
If you enjoy mechanical forensics and seeing how things work (and fail), make sure to subscribe and hit the bell icon for more engine teardowns! #machine#Equipment#Engine
AI Generated·May contain errors
Today I'm going to show you what's inside of this Mercedes smart diesel engine and how it works.
Now this engine produces a mere 41 horsepower and that's the exact opposite of this Mercedes
V8 that I just tore down which produces 460 horsepower. Nevertheless this is a three-cylinder
engine with a common rail diesel. Now the AC compressor is locked up, the alternator is locked
up, apparently the starter was locked up and burnt up, but the engine does still roll over so we're
Contrary to what you might think this is a normal engine, it just sits a little bit slanted.
We've got our accessories up at the front here, there's even a turbocharger at the back here.
Yeah and it still produces only 41 horsepower. Regardless the smart is a very light car anyways.
On this side here you can see we've got our intake with our large drive-by wire throttle
body motor that comes into the intake on this side even though you don't need throttle bodies
on diesels. Now this is from a 2005 model with 300,000 kilometers on it. The direct injection
rail is over here and it's got its little pipes that go over to the three injectors sitting on
top of here and this is the direct injection pump driven off the camshaft. I'm gonna go ahead and
start removing anything. Yeah all right so it's a 14. I might have to use my timing cover removal tool
here, give it a little encouragement. I've still got a couple of drops of fuel inside. All right
let's see if we can pull the injectors first. It's a decent sized injector, it's got some grease on
there. Next up we got the fuel rail. So on the back side here there is a sensor for the pressure
and on the front side here we have some hoses. Oh there's some fuel dripping out. So one of the lines
leads down to this clear line over here. Interestingly held together with zip tie. There is a sensor over
here. Let's get some stuff off the front here. You can pull this down. Here we have the glow plug.
This box is actually the intake, so cute and small. I'm gonna go ahead and remove all the
detents holding it to the box. Get this hose out of the way. Executive decision.
One vacuum hose is gonna hurt. Now I can get this intake off. Cute little intake. Check out all the
carbon material built up inside of there. Ports themselves inside are also pretty nasty. It's a
cute little intake that also doubles as an engine cover. Now diesels are compression ignition. When
the piston moves up it just ignites because of pressure. They don't need spark plugs. In fact
they just have these glow plugs here to warm up the cylinder on cold mornings only. Coming around
the back side of the engine here you can see the exhaust coming out here and that goes into I think
it's the EGR valve. There's also a coolant line leading here so I'm going to go ahead and see if
I can remove this E12. So this EGR fastener here is a little bit too rusty and harder to get out.
I'd rather get it off with the exhaust manifold which is actually part of the turbo as you can see.
These are 12 millimeter rusty bolts. Looks like I'm gonna have to break them for you one by one.
Okay turn. Look at this one I had to bang a 10 on a 12 just to get that out. Let's get the rest of
this turbo manifold out of here. Even way back 20 something years ago they're still using non-reusable
clamps. It's okay I'm not going to be reusing this hose anyway. That's the coolant line that goes in
to mix with your exhaust and it comes out here. Yeah we could take off the exhaust manifold and
one thing with EGR systems is that it really gums up your intake. As you can see look at all
of the soot and crust inside of this EGR intake valve here. That is absolutely crazy and with
diesel engines that burn really dirty like this it makes it even worse. Now this would be your
turbo housing with the wheel inside here. This is the wastegate that controls if that turbo wheel
is going to spin or we're going to dump all that exhaust out this way to the downpipe. While I'm
here I've got to remove this little engine mount so I'm going to use my cylinder head removal tool
here. That's fine. Oh damn. We'll get the two footer on there. There we go that turned it.
All right look at this you can't even see what this is. There's the upper engine mount. Now I'm
going to turn my attention back up right to this crusty direct injection pump. Sometimes my 3H
drive E10 socket doesn't fit onto those things properly but you can get away with using an 8
mm E10. I figure it just needs a little bit of encouragement here and pull off this direct
injector pump. Oh it's so stiff. This is a return fuel system. We've got a pump coming in here that's
going to bring it from the tank. This is going to spin up with this camshaft over here to pump it
to many thousands of psi and then send it to the injectors located on the block right in the middle
here. Now we finally get to pop the hood to see what's underneath. Remove all the E10s holding
this valve cover on. My timing chain cover removal tool here. Oh no look how black it is in there.
Looks like there's a plastic baffle in here. Can I take that off? Every time I got to use this tool.
So this baffle is actually metal and there's just baffles where the oil air is going to come in here
try to get trapped before going out this little vent tube over here. It's basically a positive
crankcase ventilation system. So I lost my toothbrush for a sec there but here's a look
inside of this Smart Cars engine. You can see you've got a very simple cam caps on top of these
cam lobes which is one for each valve. That also sits on top of roller arms down below. The condition
of the oil of course is going to be black which is expected because this is a diesel engine. This
one apparently ran 300,000 kilometers. Now that we've got the top half cleared up let's move over
to the front here where we can remove some of these accessories. This is the AC pump. It's
interesting that the pump itself is not frozen just the idler going around it. Usually it's the
other way around. I'm going to go ahead and remove it. I never realized how Canadian this car was until
I started taking it apart. Rusty piece of crap. AC pump definitely leaking a lot of this green
dye stuff which means there probably was a leak that someone was starting to diagnose.
Oh no look at all that stuff coming out. Yeah I'm not getting to sleep in the house tonight.
This stuff's gonna smell of stink bro. AC pump itself is a small yes but not that small as I
expected it to be. The smart car is a very small cabin compared to even a lot of other small cars.
I went and grabbed one of my wife's dress here and I expect by the end of this video
this thing is going to be completely black. So let's see. Mercedes really couldn't make up their
mind on the hardware for this one. This one's just using a regular 15 mil. Oh damn it's actually
turning. Well this is going to take a while isn't it? Never make such a long bolt because they often
get snapped because they're so long and twisted. Got my timing chain cover removal tool here. Let's
how much this alternator is going to fight me. All right it came apart in pieces. So this is the
joke of the water pump which is actually behind the alternator that sat here. So crusty. Now the
cooling system looks pretty simple. We've got our water inlet over here and that connects right to
the block. Then there's a piece that comes out here to our thermostat where our water connects
to the radiator. Remember the radiator on these cars are at the front of the car while the engine
here is at the back of the car. And then we've got an extra piece here that goes to our EGR cooler.
Let's see if I can remove this all as one piece. And then that can come out. Here's the water inlet
that goes into the cooling jacket. Now we got here two E10s holding this to the head.
Now I don't like that they're using a plastic inlet or a plastic connector over here. They're
also using these crimped connectors here which means that these are one-time use hoses. The
thermostat lives in there as well as the coolant temperature sensor. Let me just remove this crank.
Thankfully I was able to remove this crank bolt before mounting this to the stand. On the other
hand the idler pulley is made of plastic. I knew it was going to snap. Get this dipstick out of the way.
Okay I got a bunch of E10s to take off to get this timing cover off.
See they even bolted the oil pan to the timing cover. There's this upper timing cover piece that
comes out. See this here is a little vacuum pump. It's got this little piece on here that notches
into the camshaft and that's going to rotate to create vacuum through this little nozzle over here
to operate the brake booster or maybe the turbocharger's wastegate. Remember this was long
before the time of electronic wastegates. Inside of here there's two head bolts that I need to
remove because they go into the timing cover down below. I'm going to attempt to see if this timing
cover will come off. You never get that in modern... Oh there's oil! The old microfiber cloth here.
See the oil pan is full. I did not remove the oil. I'm going to take off this little vacuum switching
valve here. The bottom of the smart car's oil pan does not have any drain plug on either side.
Instead they expect you to siphon it out using that dipstick that I pulled out earlier
with a special extraction machine and then dump more oil in it to do your oil changes. So all that
oil that I have in there is going to have to come out somehow. Taking a look at the very simple timing
system on the smart car engine you can see we've got a chain here for our oil pump off to the side
and then our main chain here with our tensioner that goes up to a single overhead camshaft.
Obviously there's no variable valve timing. It's a very simple steel gear. It kind of takes you back
to the older school engine. To be honest you could probably just pour fuel into this thing and it'll
run because it is compression ignition. You don't need anything with the ignition system because
there's no spark plugs and there's no electronics for the timing system. The gloves will start
getting black. I'm going to start removing the timing system. Timing chain tensioner has got a
oil galley right behind it and it's also spring-loaded but there's no ratcheting mechanism.
Here it's connected to the block and the head so I'm going to have to come up with another way
with a special tool to get this off. The least I can do is get this chain off here.
Supposedly these are threaded. I already tried it on this side and it snapped off so that made it
worse. I'm assuming you'd use a puller to pull this one out and since I can't pull that...
Oh it just falls off. Does the other one fall off? I gotta say this timing chain slide is
really chintzy. There is a little tiny bit of wear on there but if this has 300,000 kilometers on it
it actually held up pretty well. The tensioner side for this slide here is actually a little
bit more worn through than the other side. Now for the cam gear there's some tiny e8s on here.
I can pull the gear out. For the cam caps we're looking at e10s. I'm going to use the old dress
to just wipe this down so we can take a look at those cam surfaces. Those cam surfaces are
beautiful. This engine probably didn't have an oiling issue. Next we can pop out the camshaft
and I'll just wipe this down again. Now before you make fun that this is such a tiny camshaft
remember v6 engines have something very similar because they too also power three cylinders
on each bank. Moreover Subaru's h4 boxer engines have two cylinders on each bank so they'll be a
little bit shorter than this. Nevertheless this one's pretty hefty and I don't notice too much
scoring or anything on here. It seems to be in pretty good shape. Looking down inside of here
looks like we've got our little roller arms. Okay I don't know if this was me but this roller arm
here is a little offset and it looks like we got some damage in here. That little hydraulic
lifter is not happy. All right so this one looks kind of sad. You can see there's a sleeve on here
that's kind of broken. I'm wondering if that's from the cylinder head itself and this is what
a regular one looks like. I also noticed that that valve was clean while all the rest here are dirty.
I also noticed there's some damage inside the cylinder head. It almost poked a hole through
the cylinder head over here as that roller arm was kind of pushed up against the head over here
and this area inside the hydraulic cylinder is all eaten up which would probably leak oil
pressure. Before I can get these head bolts off I've got to use the old toothbrush here.
Brush off all the sand and crusty deposits so I don't strip the head bolt. These are a t55.
Pretty tight for a little engine. Zip these bolts off. Timing chain cover tool here.
Pop this off. Oh it's so cute. This engine is small. I can put my whole palm over it. It is a 0.8
liter engine but it is a diesel. It produces a bit more torque and it's got this characteristic
bowl over here for a direct injection to help propagate fuel and air to mix. The bottom of the
engine head here is characteristically flat especially compared to a modern engine which
has more of a bowl shape and four valves per cylinder. Here are the glow plugs. There's no
spark plugs on these and here's where the direct injectors we inject into. Now this flat two valve
design really reminds me of older school engines. All right I'm going to try to drain this engine
so let's see how much mess we're going to make. It was dead in there. My battery died. Didn't make
too much mess though. The engine sits slightly tilted because it's a small engine bay that's
why it's like triangular shaped. Looks really weird but the worst thing is that there's no
drain on it. I'm going to go ahead and remove all the EDH's that hold this on. Timing chain
cover removal tool here. Doesn't look too bad. I don't notice any sparkles in there. Now I'm
thankful that it is made of steel but it is quite a rusty steel. I'm just not thankful that they
could have easily made a drain bolt at the lowest point here to make oil changes so much easier.
Next up we have our oil pickup tube. This is going to splatter isn't it? I'm going to use my wife's
to protect my old shirt. So for a sec there I thought it was fully clogged up but if I poke
a pin through here it's just the oil that kind of made that build up look like that. Before I can
remove the upper oil pan I got to get this oil cooler and filter assembly off. Oh no! Take a look
at this filter. Looks pretty clean. I mean it's black because it's diesel but I don't see any
particles that stand out to me here. Looks like the oil cooler takes coolant from the cooling deck
here and then we've got a couple of e10s here. Oil cooler filter and pressure switch assembly.
Now with the engine upright the rest of the oil draining down I'm next going to remove this T45
for the oil pump. Screwdriver in here. Next I'm going to remove these e12s holding this bottom
pan on. Get these e10s. My Mercedes approved oil pan removal tool here and this will check to see
if I missed any bolts. Pry. There's only two main cap bolts for these bearings. I don't see any damage
to these bearings. Amazing they held up pretty nicely for $300,000. I'm not suspecting any
oiling issues on this thing. Connecting rods are now going to be offset at 120 degrees apart
because that would be your firing order. I'm going to take off this oil pump chain over here on this
side. I'm going to get these e8 connecting rod bolts off. Now if you guys remember I was blaming Honda for
using eight mil headed bolts for their connecting rod caps and their turbocharged L15 engines. Those
are producing 150-200 horsepower. This is least acceptable because it's only 41 horsepower. Using
the cloth here to wipe this down so we can look at the connecting rod bearings and as you can see
connecting rod bearings are in decent shape. Now I'm going to go ahead and remove this crankshaft.
Crankshaft's got a bit of weight to it. I'm going to go ahead and use my piston popper tool
to push out these pistons from their bores. Taking a look at the piston design here first thing I
notice that the head is very thick and heavy. Part of that is because they had to machine out this
bowl here for the direct injection flame propagation. Also because diesels are compression ignition
engines. That means as this piston is moving upward you got a certain amount of air already
in there and you add fuel it's just going to self-ignite. You don't need any spark plugs to
ignite it and you don't need a throttle body to control the amount of air in there. The crankshaft
rpm is basically controlled by how much fuel you put into the engine and of course less parts always
make cars more reliable. Diesel engines in general are also very sturdily and well built as this one
I tested 300,000 kilometers. As I mentioned before this engine really has an old school design to it.
Check out how thick those compression rings are. They're really really sturdy on there and let's
check the oil control ring. This is so thick as well compared to the modern stuff. Look at that
it's got the plastic backing on there and then inside of there you have the corrugated spring.
This channel in here is so big compared to low tension rings from nowadays and that allows the
oil to be scraped off the cylinder walls and go back in here as opposed to getting clogged up
because this is too small. The engine's bore is actually quite tall and you can see that in the
connecting rod length so even though it's only 0.8 liters in displacement this engine does take
up a lot of space vertically. So just for giggles here's the Mercedes smart 0.8 liter divided by
three cylinder or 0.267 liters of displacement on this cylinder whereas on this guy who's got
a 4 liter v8 or 0.5 liters of displacement. The big thing you'll notice is the connecting rods
are a little bit longer but the diameters is really what makes the difference here and that's
how you can see the smart engine is so tall for what a small engine it is. So now that we're down
to the bare block in this Mercedes smart engine let's take a quick look at the oil lubrication
system. It's going to start at the bottom here where we have the oil pickup tube drawing in oil
from over here and that's then going to be sent to this oil pump on the front of the engine driven
off of the timing chain. Now that oil pump is then going to send oil down to the side here where it's
going to go to the cooler and the filter and then be sent down this hole over here into the block.
Now the engine block is going to take that oil and send it down to an oil galley that runs along
the length of the block over here and you can see these oil sprayers are going to tap off of it
in order to lubricate and cool the cylinder walls with oil. These main bearings here are also drilled
to tap down into that main oil galley and you can see the end of that oil galley over here. Now the
timing chain sensor also sits at the end of that oil gallery and the oil is then going to split
off and go down this way to the head. Also to know we have an oil drain back and an oil supply from
that oil gallery that's going to go to the turbocharger. Now the oil is going to come through this hole
on the deck here where it's going to go through the head. Also to note the cooling system which
is an open deck design. This is not a high stress high power engine and at the bottom of the head
the oil is going to head up through this hole here and that oil is going to meet a cross drill oil
gallery running along the length of the head to power these hydraulic lifters and at the end of
that oil gallery is where our hydraulic lifter had an issue. As you can see there is a little bit of
damage inside of that hydraulic lifter's pocket there and where the rocker bumped into the head
and that would definitely cause some ticking and of course some misfiring if that valve is no longer
opening. Now with that kind of racketing around and a misfire and only a three-cylinder engine
you can imagine the amount of vibration and racketing this thing would cause. Now while the
smart car I think was a bad idea for North American roads, I think this engine design is actually
pretty industrious and old school and held up pretty well. I'm just thankful that in the later
generations they added that missing cylinder to this engine and made a bigger one so that it can
accommodate our roads. Let's be honest you don't want to be that cyclist stuck behind one of these
cars. And that's a look inside of the OM606 Mercedes smart diesel engine and how it works.
Now I had good fun tearing down this engine and learning how it works. It's a bit different than
our typical automotive engines that we see and I look forward to tearing down more automotive
technology and sharing it so we can all learn how it works. Make sure you subscribe if you want to
see more videos and teardowns just like this one. Now I gotta clean up all this diesel oil mess.