The Ultimate Guide to Changing Transmission Fluid on Your Toyota Camry

Auto Retech
2 followers
Hey everyone, welcome back to the Autotech Garage.
My name is Keith.
Today I've got with me this Toyota Camry.
I want to teach you all the ins and outs of changing the transmission fluid on this vehicle.
It is a complicated procedure.
There's no dipstick.
There's no dipstick tube.
There's no way to fill this from the top, and it's a little bit tricky if you don't
know the steps.
So I'm going to bring all that information to you here in this video and give you some
confidence here to change your own fluid.
This is not completely unique to a Toyota only.
A lot of the manufacturers are going to this method where they have what they consider
a sealed unit or a lifetime fluid or all these things.
That's completely nonsense.
You still want to service the fluid on your transmission from time to time.
This is how you're going to get the longest life out of it and keep your car properly
maintained.
So let me show you all the steps on this particular car, and let's get right into it.
Before we get started, I just want to show you some of the tools and materials we need.
I've got here a couple of new drain plug and fill plug gaskets.
They're the same part here.
A couple of sockets.
These are some Allen drive or hex head sockets in a 6mm and 10mm, 21mm for the wheel to take
that off.
A little can of brake clean.
We're going to need that.
We're going to make a little mess while we do this.
I've got a flat head screwdriver.
We can use that to remove all the clips on the covers and swap out your drain plug gasket.
I've also got a 24mm socket here, and it's on a half inch breaker bar.
That should get us inside the wheel to take the fill plug out.
A couple of ratchets here, a 3-inch drive, and a torque wrench and 3-inch drive so we
can torque down the drain plug.
Also, I've got my little Makita tool here with a 10mm socket on it and an extension
so we can get all the bolts off the covers.
I've got a half inch drive gun here.
We can take the wheels off, and the socket will go with that.
I've got this tool here that's dripping on me, and we're going to use that to fill the
transmission up.
This is how we're going to get the fluid pumped up into the hole in the side of the fender
here.
I've got 6 quarts of Toyota WS fluid.
I don't think we'll need it all, but we've got enough there if we need some extra.
Alright, so here's what's unique about this car.
We pop the hood.
We want to check the transmission fluid.
We want to fill the transmission fluid.
None of that's happening from under here.
We can't access anything.
You can just forget about it.
Just close the hood.
We're going underneath.
I'm starting here at the left front wheel of the car.
This is the driver's side front wheel.
I've got the wheel turned out.
If you're doing this at home, this is probably how you'll do this.
It is easier if you take the wheel off, and certainly for this filming process here, I'm
going to take the wheel off so you guys have good access to see what's going on in here.
Let's go ahead and get the wheel off of this, and I'm going to show you where the cover
is.
We'll remove the cover, and I want to show you where the fill plug is.
That's what we're trying to access right now, is this is how you're going to fill the transmission
fluid on this particular car.
Alright, so if you come on in here, there's a cover here.
It's got a couple of bolts that hold it on, and there's a couple of clips that'll have
to be removed, and we need to take this out of the way, and I'll show you where that fill
plug is.
I just want to remove this little pop clip, and we'll take this out completely.
This is going to free up the corner of that, and I've also got a couple of screws here,
10mm, and then this access cover comes off, and then right here, if you come in low, you'll
see there is a large bolt here that is the fill plug, so we're going to pop that out
and give us access to fill this transmission.
Alright, I've got a 24mm socket here on a breaker bar.
It's not very tight.
You just want to pop it loose, and then it should spin out by hand.
I know it's a large head on here, but it's not extremely tight, and you probably need
a breaker bar instead of a ratchet.
There's not a lot of clearance in there, but this is what the fill plug looks like.
We're going to remove the four bolts along the front here.
There's an access hole in the forward cover for you to get to one of the bolts here.
This front cover also covers up a portion of this middle bolts on here, and what I usually
do is I'll just kind of pry them down, so if you pry it down, you can get access to
them without taking the front cover off.
These, you can remove through the holes.
This one here as well.
I'm just prying the corner of that front cover down, and then one more bolt over here, and
those will come out.
Then all we have to do is remove the clips from around the perimeter here.
Just using a screwdriver, pop the center out, and then pull them down.
With all the clips removed, this cover will come down in the back and then just slide
towards the back of the car.
If you look here, you'll notice on this cover, we didn't remove this portion here.
This covers the drain plug and the oil filter, and that doesn't have to come off in order
to get this entire cover off.
With that out of the way, we can use a 10 millimeter Allen socket right here in the
drain bolt.
We're going to go ahead and pop that loose, and then we'll take it out.
All right, so now inside this hole, there is a smaller hexagonal socket needed that
goes into the fluid check tube, and we're going to take that out.
This is the only way you can drain the fluid.
We've got to get this tube out.
It's not very tight.
It's a small little plastic tube, but we've got to get it out completely in order to get
the fluid out.
We're going to do this kind of like you do an oil change.
We're going to get as close as we can.
We're going to yank this thing out of here and see if we can get it all in the bucket.
If you guys are doing this at home, you've got to understand that it's a lot like changing
the oil on your car.
The transmission fluid is going to make a mess.
Just be prepared for that.
Make sure you've got plenty of rags and things.
I want to show you, I've got this wiped off a little bit, what this tube looks like.
When this tube is up in the transmission, it allows the fluid level to be this much
higher than the drain, right?
That's why when we take the first plug out, very little comes out.
Once we pull this tube out, it allows you to access the rest of the fluid that's in
there about this height across the bottom of the transmission.
You notice on here as well, there is no pan to take off.
Normally, we would have on a regular car, it might be a transmission pan with a drain
plug on it, maybe a fill plug.
This doesn't have that at all.
There is no filter to service in here.
There's nothing else that we need to touch inside.
I've let this drain a little bit here until it's got a slow drip on it.
That's going to get the majority of the fluid out that we're going to get out of it.
I've cleaned up my tube here, the fluid check tube.
This is where the socket goes.
I don't know.
Can we see that?
The socket goes right in here, this is your six millimeter.
When we put this in, we want to be extremely careful.
It tightens to something very light.
I think it's somewhere around 15 inch pounds, not foot pounds, but inch pounds.
I generally just run this in by hand, and then I'm just barely going to snug it up with
my ratchet, especially this long ratchet that I'm going to use because 15 inch pounds is
basically nothing.
It just needs to get in there snug enough where it doesn't back its way loose at all,
and it is a piece of plastic.
I definitely don't want to crack it by any means.
If you have an inch pound torque wrench, it would be something with a quarter inch drive
on it, and very light torque on it.
Put it in by hand, and I'm just going to snug this up very, very, very gently.
Don't use a whole lot of leverage.
That's about it.
It's not going anywhere.
We're going to reinstall our drain plug here with the old gasket on it because we've got
to take it out again when we check the fluid level.
For now, we're going to put this in.
We're not even going to torque it.
We're just going to snug it up with our 10 millimeter Allen style socket.
Just snug it up.
It's coming back out again, and then we're going to fill this over here.
I'm going to show you the fill procedure.
You're going to need some kind of a pump or something, or if you've got a funnel with
a long hose on it at home, this will help you get the transmission fluid in.
You don't necessarily need the tool that I have here.
I'm just going to show you how I do it here in the garage, and you can pick your method
when you get going.
Here's the tool that I've got that we're going to use to pump the fluid back up into that
hole.
Now, when we're working underneath the car, this makes it easy for us.
We can just pressurize this canister after we've added our fluid to it, and then we can
fill it until we want to stop, and then we can just turn it off.
It's nice to have this tool.
It's made by MightyVac.
I don't care what kind of tool you use.
Like I said, you can use a funnel with a long hose if you want.
That'll get you in there, and I want to make sure you guys are using the right fluid.
This vehicle calls for Toyota WS, their world-standard transmission fluid, and this is their particular
blend for it, so there's other options out there.
You can certainly go to a synthetic oil, and there's compatible products that you can probably
put in here.
I'm always a fan of just sticking with what the manufacturer recommends most of the time,
so you're certainly able to explore your options if you want, but Toyota WS is the correct
fluid for this transmission.
I'm going to put about four quarts of Toyota WS fluid in my tool here.
This way we have enough to finish the service on it.
It'll probably take somewhere between three and four quarts.
I think the spec on it is 3.4 quarts.
It's going to have to vary a little bit depending on your situation, so we'll start with about
three quarts probably, and probably have to put a little bit more in there, but either
way I like to have enough to get going.
Like I told you guys before, it's really nice to have a tool like this.
We do a lot of transmission servicing that requires this tool.
There's a lot of different adapters.
On here I've just got one that's basically a little elbow, like a 90 degree, and this
actually hooks in the hole when we fill.
There are some other cars where there's little adapters that thread into the pan, and you
need that in order to fill it.
The transmission fluid filling and servicing procedures have really gotten complicated
over the years compared to what they were a couple of decades ago.
I should also mention too, I talked a little bit about this Toyota WS fluid, and using
the correct fluids when you're servicing a transmission.
Please make sure you're following your manufacturer's recommendations, because there's a lot of
different fluids out there for transmission, especially if you're working with a CVT transmission.
That's not a conventional automatic transmission.
It's a continuously variable transmission.
It works completely different.
It's got a belt and some sheets on the interior of it, and they're problematic, and they definitely
need the correct fluid in there at the correct level.
Don't mix and match those with standard transmission fluid, but even if you see a transmission fluid
like this that's pink in color, it doesn't mean that it's a typical Dextron Mercon.
It's probably something special, and you definitely want to make sure you're using the right stuff.
Once we install this lid, it's going to seal this container up.
I've got a little shut-off valve on here, and I'm going to turn that off at 90 degrees,
and then we can just pump this and pressurize this container.
It's got a little bit of a gauge on here, a green and a red zone, so I usually pump
this up to the top of the green, and this should give us enough pressure to get three
quarts of fluid back into this transmission through that fill port that we have on the
side of the transmission.
I'm going to show you here into our drain bucket the amount of pressure that actually
comes out of here once I open this.
I'm going to crack this open.
You can control the pressure on it here, but you see it just kind of streams out, nothing
crazy, and we're going to start filling this a bit.
We're filling now, and this can make a little bit of a mess here with some of this fluid,
so I'm just going to try to hold it in place, see if we can get about three quarts of fluid
in here.
Now, in the manual, it'll give you an actual level, how much you're supposed to put in
there, maybe 3.4 quarts or something.
It really just depends on the type of service you've done according to the repair instructions.
I haven't found that to be all that critical.
I usually go about three quarts on these.
If you overfill it a little, it's okay, because we're going to drain that back out.
If you underfill it a little, that's okay too, because we've got three quarts in there
and it's going to take something close to three, three and a half, so I find three quarts
is a good starting place, and once we've got that in there, then we're going to show you
how to do the level check on it.
Now that we've got three quarts of fluid in this transmission, I've left the fill plug
out.
This way, if we need to add some, we can.
The drain plug is installed again, obviously, and we need to get this vehicle at the proper
operating temperature.
Not the vehicle so much, but specifically the transmission fluid.
It needs to be between 95 degrees Fahrenheit and 113 degrees Fahrenheit.
This is the operating range for the transmission fluid when you check the level.
Not only does it have to be within that range, but it also has to be in idle control mode,
so they don't want the engine idle coming up and down, surging or anything while you're
checking the fluid, because we've got the vehicle running and the pump inside the transmission
will obviously be circulating the fluid, so we want this to have a very precise level
draining out of that overflow tube while we check the fluid.
What we've done here to do this without a scan tool is to jump out the terminals inside
the car.
I'm going to put up a diagram for you guys so you can see which terminal specifically
to jump on the OBD port.
It's terminal 4 and terminal 13, and we're going to follow this procedure exactly.
Once we start the vehicle up, we're going to move this shifter from park down into drive,
slowly back to park, leaving a few seconds in each gear selection.
Once we've done that, then we're going to take this shifter, we're going to put it all
the way down to drive, and we're going to go back and forth between neutral and drive.
We're going to do this about a second in each, it needs to be less than 1.5 seconds in each
position.
So down to drive, less than 1.5 seconds, back to neutral, back to drive, back to neutral,
back to drive.
We're going to repeat that process for at least 6 seconds.
You may need a little bit more, I've seen this take a little bit up to 10 seconds on
some vehicles, so we're just going to rapidly move this shifter back and forth, and what
we're looking for on the instrument cluster is the gear range indicator is going to illuminate
for a couple of seconds.
The drive specifically, the D letter, is going to illuminate on the dashboard for 2 seconds.
After we get that drive light to illuminate, we're going to put it back in park, and that
drive light on the instrument cluster is going to do one of three things.
It's either going to go out, it's going to stay on steady, or it's going to start flashing.
If it goes out, the transmission fluid temperature is below 95 degrees.
If it comes on steady, the transmission fluid temperature is in the proper zone, 95 to 113
degrees Fahrenheit.
If it starts flashing, it's over 113 degrees Fahrenheit.
So we can't check the fluid if the light is flashing, we can't check the fluid if the
light is off.
We're waiting for that D light to stay on steady after the initial 2 second illumination.
I'm going to go ahead and get started, and hopefully we're successful in activating these
two modes we need in order to check the transmission fluid level.
I've already got the jumper installed between terminal 4 and terminal 13.
We'll start the vehicle up, and then we're going to go for a few seconds in each gear
selection, all the way down to drive.
Back to reverse.
We're going to finish in park, and then we're going to move this gear selector.
Okay, so now the drive light is illuminated, and it's on steady, and it's letting us know
we've got the vehicle in park right now, but it's in drive on the instrument cluster.
So that's letting us know that the fluid temperature is in the proper range.
So we need to quickly get out here, under the car, and check this fluid level.
Let's do it.
We've got to pull this jumper wire out in order to get this in idle control mode.
All right.
All right, so we've removed that drain plug, and you notice there's not much coming out
of here.
We just had that initial splash on it, so we're going to fill this some more until we
get a small stream coming out, and then we're going to let it sit there until we've got
just a bit of a drip, no more stream, and we're going to put the plug back in.
I just want to mention, you see how this is kind of splattering out now?
That's about what you want it to look like, and as soon as this slows down to a slow drip,
we're ready to put this plug back in and wrap this level up.
It's right where it needs to be.
So like I told you before, I put about three quarts in here, and three quarts is usually
enough.
This is right about where we want to be.
Like I said, I think the maximum capacity on there is about 3.4 quarts, so this is the
proper level.
We're going to cap this up here in just a second, as soon as it stops dripping out,
and then we're ready to install our fill plug and put the rest of this back together.
Okay, you see how it's slowing down now, just to kind of like a steady drip?
This is about what we want it to look like here.
Maybe a hair slower, right about there.
I put my new drain plug gasket on.
We've got this little slow drip going on, and that's about where you want it, and then
we're going to put this plug in.
Now, I'm just going to snug this up for now.
We'll torque that on after we get the vehicle shut off, but I want to put that in, and I
want to put our fill plug back in.
Now, I want to lower the vehicle back down, shut it off, and we'll torque everything up
and put all our covers back on.
All right, we went inside, we turned the vehicle off, and we raised it back up in the air.
Now I just want to come back and check my torque on this drain bolt.
It's supposed to be at 37 foot-pounds.
We'll get this one torqued up right there, 37, and then this other one here is not quite
so important.
Just snug it up.
It's a fill plug.
It's not going to leak or anything.
The fluid level is way below where the fill plug is on this transmission, so you don't
even need to worry about that one.
I would just say snug it up, not too tight again, and definitely not loose, okay?
I like to use a little bit of brake cleaner, just kind of clean up some of the leftover
transmission fluid.
I went in here and just wiped up a couple of the big spots that I dripped everywhere,
and I'm just going to make sure that when we're done here, we're going to put a cover
on it.
We don't want stuff dripping in here for days.
If you want to spray around your drain plug, too, that's usually a good idea, and then
come back in here and wipe everything off.
Last thing you want to do is leave some stains in your driveway or garage because you let
transmission fluid leak into a cover or into the frame rail or something that you weren't
able to get cleaned up.
We'll just kind of tidy up all these work areas here, and then we are ready to start
installing all our covers again.
We'll be reinstalling this side cover.
This kind of goes in behind here, and then the two screws will line up to the holes back
here.
We'll get these started by hand, and then once they're in a couple of turns, we can
run them in.
We'll reinstall our clip.
Now we're ready to put this lower cover on.
Just going to reverse the removal procedure.
We've got four bolts and a bunch of clips.
Just make sure you're installing these bolts by hand.
We don't want to cross-thread these.
We're going to have to wiggle this cover around a little to get everything lined up.
Once you do, the bolt should fall right in the hole.
Go ahead and get it in a couple of turns, and you're ready to snug that up, too.
We've got the side cover on, the lower cover's installed, everything's torqued up nice, and
we've just got to put the wheel on last here, and we are ready to wrap this job up.
Now that we've wrapped up this transmission service on this vehicle and demonstrated how
to properly adjust the fluid level, I hope you guys learned a couple of things here.
The process is not terribly difficult, although doing this on your back is really cumbersome,
so if this is something you plan on tackling at home, just make sure you've got a nice
bundle of rags.
I'm sure you see in this video that we made a little bit of a mess here.
You definitely want to get that cleaned up when you're done.
If you're floor, you're using your garage, and it's going to absorb some of this oil,
make sure you've got it covered up because there's not really any easy way to do this
without making a mess, and I don't want you guys to stain your garage floor or your driveway
or something if you're trying this at home.
Hopefully you've understood the procedure to get this thing into its fluid temperature
detection mode and idle speed control mode.
It's a little weird that they make you do this on this car.
It's kind of a bit of a process, but that's what they want from the manufacturer.
If you want to do it correctly, that's the way to do it.
I hope you guys found this useful.
If you're not going to try it yourself, at least you understand the procedure when you
bring it into the garage, and somebody's going to do this job for you, you understand what
they've got to go through, and probably why it's going to cost you a little more than
the average job here when you're looking to do a basic transmission service.
I hope it was at least informative for you.
I hope you guys are enjoying this content.
We've got a lot more coming for you.
Go ahead and check out this next video we've got coming up for you over here.
We'll see you in the next one.
