Intro to Mixers - AudioTech

TheGospelGuitarist
1 follower
Mar 31, 2026
An introductin to audio mixers.
AI Generated·May contain errors
going in and out of it. But today we'll discuss this component of the sound system.
Whether you do live audio or whether you do home recording, you may need one of these.
And so what do all these knobs do? The first thing people do is get afraid because they see
so many knobs. And what I want to show you is that these are all organized and most of them just
are duplicates. The mixer has a channel section which can vary in number. This specific Yamaha
here that I use has 16 channels with the gray faders. And from here over are just your input
channels. This side is your master section. Now out of all these channels with all these
knobs it just looks mind-boggling. So what I want you to do is in your head just shut all this stuff
out and just picture one channel strip. Now at the top we have a line input for XLR. This is where
you would connect your snake going to the stage or in the studio would just plug in a microphone
or DI box. But basically it's a microphone cord that goes plugs in here. Here you have a line
input for a quarter inch for like guitars in your home studio. And underneath this you have what's
called an insert. And this is where you insert things that you're going to need on that channel
be compressors or some type of EQ or effect device. And it would only be used with this
channel not all of those. We can get into those later. Next section on the mixer we have a gain
control. And this controls how much gain your input has of whatever's plugged in up here on
your mic or line and line feeds. Now this particular mixer also has a built-in compressor
on six of the 16 channels. So this one here is just a single knob compressor. It's nothing fancy
but it just kind of kind of helps with what this board does. The other thing you have on just about
every board is an 80 hertz roll-off switch which engaged will kill the low rumble frequencies on
stage of the kick drums and things like that that are going on. And it'll just clean up your signal
if you get that low end rumble a lot. Okay next on the line moving down we have a high frequency
control with a peak indicator. It's a red led so if you're getting too hot of a signal coming into
your channel this will flash. It's okay if it flashes intermittently but don't let it stay lit
or really lit. So there's your high frequencies. Below that we on this board and any board that's
worth its money you're going to have a sweepable mid band eq. So on this board I have one
control it's referred to as a parametric mid which allows you to select a mid frequency
and then cut or boost it. And that comes in handy with feedback and just annoying room frequencies
if you have a frequency that's just really annoying you you can find it in here turn it
all the way up until you find that annoying sound and then just zip it right back out by lowering
this knob here you can cancel that annoying feedback or just something bad in the room
that you're hearing. Okay below my eq section on this board I have auxiliary section and this can
vary on some boards as well but the layout on all boards is basically the same. On this board
I have an aux 1 and I have an auxiliary 2 okay and also with this or your headphones in the studio
and then aux 2 you can use for outboard effects. Okay next on the chain we have a effect knob
and not all boards have this but most of the boards coming out today have some type of
effects built into them they don't all come that way but those that do have this knob located
somewhere on your channel usually at the bottom and this just controls how much of the signal
in this channel is going to go to the built-in effects unit whatever that effect might be reverb
on a vocal so if you put it way up here you're going to get a pretty wet reverb and if you turn
it down it's going to be a dryer but it's not as dry as if it's totally off. Right below this knob
you have your pan so you can have a stereo sound you're just going to pan left or pan right
and on these are also for assigning to buses and we'll get into buses later.
Okay the last section on most of the boards not most all the boards you usually have some type of
on and off switch that will on this one it illuminates some of them have just a normal
push button and might have an led next to them but there's some kind of on and off or a mute
they're both the same thing if it's on obviously it's not muted if it's off then it's muted
the pfl stands for pre fader listen so the signal that's come all the way through this
chain that i've just showed you when you push this button you can hear what that sounds like
privately through the headphones plugged into the board so that way you can figure out which
channel might give be giving you feedback from the stage because you'll hear it right here
below this you have your bus assign switches and on this board i have one and two three and four
and stereo and each of these have their own faders in the main section which we'll see
in a few minutes and then you have your main channel volume now this controls how loud this
channel is going to your stereo bus okay your stereo bus is what you're listening to on stage
coming off the big speakers that's your stereo bus and this just controls how much of this
instrument or vocal is in that signal and that's what these do all these faders so that's basically
it for the whole channel strip okay so now we move over from the channel sections to the master
section and here we have a master send for your auxiliary one auxiliary two and your built-in
effects these knobs control how hot they're just your master control so they control the overall
level of each of these sections over here you have your return for aux one aux two and your stereo
bus and this again these are like they're just volume controls and this is panning
how much goes to your stereo bus because you don't have to send these things there
next to that over here we have our headphone and monitoring section with a volume control
and a couple switches we can select the stereo group
stereo is your main stereo bus and then your groups are your subgroups and then this switch
will designate which of the subgroups you want to mess with either one and two or three and four
they're always paired up in one two three four five six seven eight however many you have
usually you're not going to get more than eight below that we have our
yeah check that see if you can even see it and you can okay below that we have our
the two tr in so that's an input up in this other section i'll show you in a minute
where you can plug in your two track uh playback decks for background music and things like that
during music breaks you know a band takes a break you can throw something on
and this can control that volume and this is a switch that you can select to send it to stereo
or your monitors so that's what it means by master this controls where everything
plugged into the board is routed to and finally we come down to the master fader section
where we have your effects group this is just going to control how loud your effects are
and then you got subgroup one and group two with a stereo assigned switches because if you have
these in then whatever groups these are like this might be a group of singers um and this may be a
drum kit or whatever but you don't have to send them to the to the drums i mean to the uh to the
drums to the stereo out because they could be used for recording but these are your master faders
now at the top of the board on the other half you have the master input section and output section
here are your tip sleeves for your input for your playback mp3 player or cd player
or even the sound coming off of a dvd player you have a record out which you can take out and send
it to your recording device whatever that might be you have your auxiliary sends one two and then
you have an effect send on this board so you have your auxiliary send section right below that you
have your auxiliary return section you have your group outs i have four which are the outputs of
the faders that you've just seen and then over here we have a couple choices for outputs we
have headphones we have um tip ring sleeves a quarter inch for your monitor outputs and then
you got your left and right lxrs that would lead to the stage as well as quarter so you got your
choice of outputs here so you can send things all over the place but at least this way you get a
brief overview of what what's going in and where they plug in and last but not least we have our
monitor leds which tell us our power is on and what the level of the system is and you have a
switch also that turns on your phantom power to your microphones if they need that these also
show your bus on this one i have left is one and three for your subgroups and right is two and four
for your subgroups so you can use your your pan your panning knob on each channel
to send it to one or two which is left or right respectively okay so that's a real quick video
on what all the knobs do on these boards just take it one section at a time and learn one strip and
what it does according to the manual for your board now what i've told you on this board is
pretty much applicable to anything that's out there you're either going to have more channels
and more buses or less channels and less buses you may have effects built in you may not have
effects built in if you plan on doing anything live with your board or in the studio make sure
it does have 48 volt phantom power and if you are going live as you can see this is in a case
there is a big top that goes on this and i recommend that you own one of these cases
to protect the board it's your own investment so you may as well protect it plan on forking
out about 300 bucks though so i hope the video helps you on your way to learning about audio
whether you're wanting to do it in your home or whether you want to do it live and i do both so
i will have forthcoming videos on how to use at least the gear that i own i own just about every
type so i'm going to be doing one piece after another in the series and i hope that it helps
us all learn about the audio systems in our churches and in our bands so that we can actually
sound good with whatever it is that we're doing from the music side of the of the church service
to the sermon side so i hope this helps you leave comments questions um i don't know everything about
every single board okay so it's pretty generic uh in this in this lesson i hope that you found
it helpful and thanks for viewing and be sure to share it with your friends click the button
and subscribe for further updates on more videos coming thanks for watching
