SD Jazz Triple Shot Demo

TheGospelGuitarist
1 follower
Mar 31, 2026
Demonstration of the Seymour Duncan Jazz pickup installation using the Tripleshot pickup mounting ring.
Here is the SD JB Tripleshot Demo: http://youtu.be/Qnkyp7ujmdc
Here is the Tripleshot Installation Video: http://youtu.be/shgsi52OLQY
AI Generated·May contain errors
Hi, I'm Mike Sullivan. Welcome to Guitar Tech, how to do it yourself.
Hi, Gospel Guitarist here, and today I'm going to show a little bit about what the Seymour Duncan
Jazz pickup installed with a Seymour Duncan Triple Shot pickup ring can do for you. I'm
using my trusty Schecter C1EA here, which many of you have seen a lot of videos I've done on.
And the way I'm recording this is I'm just plugged straight into channel one
on my Roland Jazz Chorus 120, and I'm recording it with a Sennheiser 421 dynamic microphone.
And as you can see, it's placed midway between the outside of the speaker and the speaker coil.
And that's pretty much the sweet area. I would have used a 57, but it went out on me,
so now I've got to take it apart and take a look at it. So I didn't expect that. So there's no
reverb on the amp. There's nothing on it at all. All the EQ is just straight flat.
The microphone and my mic are running into my Tascam 2488 directly. I'm not using any of my
tube pre-amping or anything. It's just mics straight into the Tascam hard disk recorder.
And so I guess that's about as few as it can get. Usually if I record things with this,
you know, people complain about having the Jazz Chorus turned on on the Jazz Chorus,
even though that's how people will use this amp mostly. But so anyway, I'm just going to
run it straight clean. And in this video, I'm going to talk about only the jazz pickup that's
in the neck and the way it's wired. I did make a video on the installation of these pickups
and the pickup rings, so you might want to check that out. And so because there's so many options
now on this guitar, I'm going to make two videos. This is the video covering the Seymour Duncan
Jazz. I'll make another video on covering the Seymour Duncan JB that's in the bridge.
So let's get started. First off, what we have is two switches are on the top of the triple shot,
and they allow you to make four different sonic combinations with the pickup wiring.
I have the ring standard wired. It's backwards to some. In my mind, it's still kind of backwards,
but they do give you an alternate wiring to where however your brain is wired, you can wire the
pickup when it comes to the coil splitting side of things, which we'll get to in a minute.
So what we have right now, I have the switch up, so I'm only using this pickup,
and I just want to demonstrate the tonal quality of the pickup, and that's it.
So there's a couple chords here. There's an open E chord,
a C,
and a D.
Okay, G.
Okay, it's got a nice sound, but it's really heavy on the low end.
But this is a hollow body, so I guess that's where that's coming from.
That's what this pickup would sound like if we just had it straight wired into your guitar
with no switching or anything. That's the sound. That's what you're going to get.
So now if we push both switches toward the neck, you're going to turn off the coil closest to the
neck or the coil with the screws if I remember this correctly. So the pickup that's going to
or the coil that's going to be active is the one away from the neck. You have to listen
really closely to these, so I'll let them ring out a little bit, a little longer,
just so you can hear the tonal quality for an E, a C, a D, and a G.
Okay, now to compare that back with the original wiring. E, C, D, and a G,
and a G. So it gets thinner when you go to single coil, of course.
It cleans things up pretty nice, but it doesn't drop volume a whole, whole lot.
Now if you pick, take both of the switches and you ride them both towards the bridge,
then you're going to cut off the coil that they're turned towards, which is this one,
and you're going to turn on the coil that has the adjustable pole pieces,
and this is the difference there.
C, D,
and a G. Flip them back to the other coil. G.
Cut the other coil.
It's really difficult to hear the difference between the two, but the one by the neck is
not quite as full as the one out here, because the more you get towards the middle of the two
pickups, you're going to have more string sway there, so it's going to give you a better bass
response. So if you have the inside coil running, it's going to be a little bit warmer than the
coil right next to the neck, but not much. So there's not a whole lot of difference there,
and I really don't know if you're even going to be able to hear a difference at all on the video.
So I chose to use my very clean amp, and I'm not running any distortion. I'm trying to get
the cleanest signal I can for you. I can hardly tell the difference in the room sometimes.
But if I'm working on a song, sometimes those little tiny nuances of the pickup is noticeable,
and I like it because I get four wirings, and the little switches are right there. They're
just really easy to get to, and I like to have that variation. My favorite on this guitar is
actually what I'm going to do next. If you take the two switches and you push this switch closest
to the neck towards the neck, and the switch closest to the bridge toward the bridge, you have
what's called parallel mode. Now parallel mode is going to cut the pickup output, I think it's by
50 percent. It drops quite a bit. It drops about twice as far as what a single coil gives you.
So not only do you get a single coil type tone,
but it's almost an acoustic sound, and I really, really like this sound on this guitar.
So as you can see, there's some bottom end there, but it keeps that nice,
it has a clarity of a single coil, but the warmth of a humbucker, and there's no noise.
Now personally, that's my favorite on this guitar. Whether I'm running it by itself,
or if I'm switching it and using it with the bridge pickup as well, I usually will leave this
one in in parallel. I just really, really like the sound of it, and it sounds nice and clear.
So let me pick a chord here, and I'll run through these one more time, but with one chord. I'll use
a C chord, or I'll use an E, that way you get the low end. So I'll run it through each position,
okay? So this is normal standard humbucker with an E. Lots of power, lots of high output,
lots of bottom end. Parallel right after that, so you can hear a contrast.
Yeah, a lot of that lows are gone, but it's nice and clear, and bright, and spanky.
Okay, single coil on. Let's go with the one with the closest to the neck.
Now that's going to be, it's got a little more output than the parallel mode,
and the single coil mode with the inside pickup, and there's our bass response again.
Okay, can't do it much faster than that, and there's my favorite. So I like the parallel
mode a lot. I've never played with it until I got these pickups, and I just really, really enjoy
parallel. A lot of people, you either love it, or you hate it. If you can get away with a little
less power to clean up the sound, parallel is definitely the way to go, and it almost has an
acoustic sound to it when you play. So it's got a nice clean, excellent clean highs on it. So
anyway, that'll close out this portion of the demo. Tune in for the next portion of the demo
for the JB pickup in the bridge. Well, thanks for watching, and see you next time on Guitar Tech,
How to Do It Yourself.
