SD JB Triple Shot Demo

TheGospelGuitarist
1 follower
1 Video View·Mar 31, 2026
Demonstration of the Seymour Duncan JB pickup installation using the Tripleshot pickup mounting ring.
AI Generated·May contain errors
Hi, I'm Mike Sullivan. Welcome to Guitar Tech. How to do it yourself.
Hi, Gospel Guitars here. Today I'll be demoing a Seymour Duncan JB pickup that is mounted
into a triple shot pickup ring with four conductor wiring and switching.
And the way I'm doing that is I'm playing my Schecter C1EA directly into channel one of my
Roland Jazz Chorus 120. This video is being made by recording it through a Sennheiser 421 microphone
and I'm wearing a mic for the vocal. And they're both plugged into my Tascam 2488 straight into it
using the preamps on on the unit. So there's no tube amps, there's no reverb, there's no effects,
there's nothing. Everything is flat out. The guitar is just straight up. All the EQ on the amp
is set at 12 o'clock. It's all flat. So there's nothing at all but the pickup to here.
Can't think of a better amp for doing this. So if you haven't checked out the video on my JB
or my Jazz in the Brit, in the, boy I just can't talk today. If you haven't checked out my video
with the Seymour Duncan Jazz demonstration, that's in another video that I made with the same setup.
So be looking for that and I'll try to remember to post links to that.
So let's get started with the demo here. Using only the JB in the bridge and channel one of the amp,
there's four modes. We have a standard mode which is standard humbucking and you have parallel mode
and then you have two single coil cut modes in which you can take your pick between the two
coils in the humbucker which one you want to use. So this is the tone you'll get just straight
as if you wired it without the ring at all. So nice bright clean sound and a lot of heat.
Now if we go into the parallel split, a parallel split, no split coil. Okay if you take both
switches that are on the mounting ring and you shove them towards the neck of the guitar,
you will be activating the pickup that has, if you wire it standard according to the instructions,
you will activate the coil with the adjustable pull pieces which is the one closest to your
bridge or the brighter of the two. Okay now the other single coil you would cut or activate by
pushing both switches towards the bridge, turning off the one that you were using just now and
turning on the one closer to the center of the two pickups. And it should be a little bit fuller
sounding. Okay now between those two maybe you know all you guys with real sharp studio ears can
hear big differences. I hear minor differences. Basically I wouldn't hear anything if it weren't
for the low end in the pickups as far as the difference in the two coils. And I know that
that's going to be affected by the string sway. So the area between two pickups is going to have
a lot of the spring, the string swaying. So you're going to get a lot more low end frequency response.
So whichever coil on your pickups is closer to that you're going to get more low end.
And that's the only way I can tell the difference. Next we have parallel. And parallel you get by
pushing each switch, the switch closest to the neck towards the neck and the switch closest to
the bridge towards the bridge. So they go this way. Now that's parallel and it'll be a thinner sound.
Okay now when you go to the parallel compared to the normal humbucking.
Now as you can hear there's a big big difference in volume output there. I have not touched
anything on volumes. I have no pedals on the floor to to cut my volume. That is strictly
what happens when you go to parallel mode. It has a single coil sound. I'm kind of wondering
if it's not more of a P90 sound. But I think P90 is a little bit more of a P90 sound.
I like the parallel mode on the bridge or on the neck pickup. But I don't really like it so much
in the treble position personally. But to each his own right. That's why we have triple shot. So we
can get all four tones out of one pickup. And used in combination with two of them like I have here.
That gives you what 16 different combinations I think I counted of different tonal qualities.
Plus I got a piezo down here. A piezo sorry for you specialist of language.
I'm just trying to break my habit there you know. This is a nice guitar for this. I can get all
kinds of sounds and I can really hear the differences because it's I guess because
it's a hollow body. I don't know if the differences will be as strong in a solid
body or not. I would think that they would. Might even make them more so. But I only have it
tried out on this guitar. I do have a Schecter C1. There goes my phone in my pocket. This
luncy list love that. So anyway I may install them on a Schecter 30th anniversary model that I have
as well which is a solid body. I'm not sure if I want to do that at this point. But if I do I
will demonstrate that one because it's got different Seymour Duncan pickups. So that's it
for the demonstration of the C1EA with actual Seymour Duncan Jazz in the neck and a
Seymour Duncan JB in the bridge. This is a run number two of a two video set on the demonstration
of these pickups in this guitar. I hope that helps you all because you've been watching me
make all the changes and I've had a few people asking what it sounds like outside of when I first
installed the pickups. And back then they didn't even have the chrome pickups on them. The pickup
covers. I put the chrome pickup covers to kill some of the high end. They are extremely bright
pickups to my ear. So I put the chrome covers on them and that softened them down just
enough for me. So maybe that's what you might want to do and it looks good too. So thank you for
watching. I hope this has helped you out. Subscribe and I'll keep the videos coming out
and lots of stuff coming. So be sure to subscribe and use the share button so your friends can find
me too. Especially those who own this guitar. So hope you enjoyed the video and thanks for watching.
Well thanks for watching and see you next time on Guitar Tech. How to do it yourself.
