Guitar Setup 2 String Action

TheGospelGuitarist
1 follower
Mar 31, 2026
How to set your string action height for your guitar.
Hi, Gospel Guitars here with a second video of the series that came with True Cruise Tools
on setting up your guitar. In the last video I showed how you can set your neck relief. If you
haven't seen that video be sure to check that one out and I should have a link in the description
below. For measuring your action in this video all you need is an accurate 60 force capable
measuring ruler and it also has millimeters on the bottom. What we're shooting for basically is
to have at the 17th fret a clearance between the string and the fret of 560 force. So you're going
to measure by putting it behind the string, not in front, can't get it to work. Go behind the string
and set your ruler right on top of the fret and check your reading and that's going to be
how to set your action. You can adjust each saddle of each string. In my case I have a
pneumatic bridge so I don't have the individual string adjustment but I can raise and lower
the bass and treble side with the thumb screws and I'm going to want to try to get it to about
560 force without any fret buzz. So be sure to do the first step first. The first step first,
that's a good place to start right? Set your neck relief first so you have the proper amount of bow
in your neck before you try doing your action setup. Now on my guitar I've measured it at about
460 force on the low end and 360 force on my high E string and I have no fret buzz anywhere on this
guitar. I'm also using the D'Addario chromes which are flat wound on this guitar so that may help
with the buzzing issue. I don't know, they don't seem to move as much as a normal string.
They're a bit tighter, more focused in the way they vibrate. In other words, I don't think
they're going and making these mini circles as wide as your normal electric guitar string does.
And that's it for your action. If you have a Floyd Rose or some other bridge that has
individual string height adjustments, then go from string to string and set the height the same.
You can go a little bit lower on the non-wound strings because they're smaller in diameter so
obviously you should be able to get closer right? Like I've lost a complete 64th of an inch between
my low E and my high E and I'm really low on this guitar. So that's all there is for setting up your
the action on your guitar. You want to bear in mind again, just like setting up the relief on
the neck, your playing style. But this is really important when it comes to setting
this spacing with your strings. Because if you're playing pretty hard metal and you're
totally distorted, no one's going to hear the thing buzzing anyway. But if you play clean and
you play hard, then you're going to hear buzzing everywhere if you're a hard player. So if you've
a light touch, you can get away with going extremely low. And on this guitar, I bought it
for jazz style type playing. Mellow tones, mellow playing. So I have it set up really low.
My other guitars, I usually go a 16th of an inch or so, even on the high side. Because you start
rocking out, I don't want to hear all that buzzing noise. So depending on your playing style is going
to help determine where your setting should be. But 564 is a good starting place. It's pretty
close to how I set up just about anybody's guitar when I'm asked to set one up. I usually shoot for
just barely under 16th of an inch. And everybody I've done that with just loves
their guitar's playability. So it's a good place to start. I agree with the specs in most of the
say 564s. And then go from there. Play it and see if you want to lower it or get it higher.
So that's it. That's how you set your action. Get yourself a good ruler. 17th fret. Measure
each string and set them to the same height or just a little bit lower as you go from the low
E to the high E. And that's it. Thanks for watching. Be sure to like, subscribe and share
the video. And I hope you found it helpful. See you next time.
