Roland GK-3 Installation

TheGospelGuitarist
1 follower
Mar 31, 2026
A How-To video on the installation of the Roland GK-3 MIDI pickup system.
Hi, I'm Mike Sullivan. Welcome to Guitar Tech. How to do it yourself.
Hi, Gospel Guitars here with another interesting video. I hope you find it interesting.
What I'm going to do today is install a Roland GK3 system for MIDI on a Schecter C-130th
anniversary model that I have here. I'm just going to go over this real quick because there's
a lot of things that are involved. The toughest part of this whole install will be
getting the pickup set up properly for your guitar. As you can see here, I already have a
bracket mounted to the pickup. I already done that and got that out of the way. You just install a
there's a couple pieces of rubber. I figure if one is good then two is better
because my bridge sits really close to the top of the body and these screws that come with it
are a little bit long for me. On a Gibson Les Paul where your bridge sits up a little higher
I wouldn't worry about the length of these screws but if you've got one of the Schecter models or
an Ibanez or something that uses the same type of of a bridge you might get a clearance problem
because these screws are just a little long in my opinion. Other than that
it's a nice system. It comes with a whole bunch of extras that you won't be seeing in the video
because I don't need them for this install. For Stratocasters and other guitars there's a whole
bunch of things that you can do to adjust the height of the pickup system. It comes with a
this little guy here just a little L-shaped it's one millimeter spacer that you can check the
string spacing so all six strings need to be that close to the pickup. Once you get it installed
you got to go through and make sure that the height is good and so if it's not you got to do
a lot of adjustments. I won't go through all of that process in this video that could be
lengthy and boring. It does come with a whole bunch of little things that you can double tape
to the guitar to get the spacing correct. There's three or four different sizes here
and those things will be used to get your guitar set up or get the pickup set up for your guitar.
Now on this guitar I'm using a mounting plate that comes with it.
This is the easiest way to install it on this guitar or a Les Paul style guitar.
So next once you get the pickup set up on here the instructions go into great detail on how
to set up the pickup itself. This is the most lengthy part of the install there's a little
adjustment screw right in the middle and this little guy comes with the pickup and you just
use it on this screw right here and what it'll do is it adjusts the pickup height
not this curved plastic piece right here this part just looks like it's a fixed it's a fixed
contour it looks like about a 12 inch radius there but the pickups there's six individual
pickups and they will kind of do one of these numbers so that you can set the radius of the
pickups to match the radius of your fretboard and that's something you want to do before you get it
on. Although I think you know you'd be fine to make those adjustments once you do get it set up
I think you're going to need to make final adjustments they don't go into that but in the
manual but setting it up off the guitar will work if you know the radius or you have a radius gauge
that you can get from Stumac they're just little plastic you know white pieces of plastic with
different gauges on them or you can get them at the guitar shops or you can just eyeball it too
so or if you if you know what your radius is that helps if not you need to research what the radius
of your guitar neck is so you can get the pickup set up to match it and that way you'll get the
best tone without a lot of tracking mistakes and tracking errors. So as you can see this is one
unit so you have the actual pickup mounted here on the mount for the tom bridge and the cable is
fixed to it and it is permanently attached to both ends so you're not going to be able to take the
cable off or unplug it or anything like that and so the next step here that we want to do is we want to
get these strings loose so I can get this bridge off and put this on. Okay now that I got the bridge
removed and the strings removed the next thing you do is when you're using this piece anyway
you need to lower your posts two millimeters to make up for the height that this will add
to the post so you want to take those down a little bit and it says about two millimeters
that's the thickness of the metal of this plate and then once you get that done you can just set
that guy right on there. There is some leeway here for the way it moves around
so it'll fit your bridge properly then all you do is take your bridge piece
and you put that back in place. Okay now as you've seen it just lined that right up
okay it did a really good job and the the arcs are matched pretty well. Now this is a Loctone
bridge here so it's got locking hex nuts but I'm going to leave those loose until I get everything
assembled and it's restrung and then all my adjustments are finished and finalized
then I will lock everything down but I would not suggest locking things down at this point
and that's all there is to installing the pickup on the bridge. You don't need to drill any holes
in your guitar so you don't have to worry about that unless of course you choose to.
I wouldn't choose to and not on this one but a strat where it has the plastic plate
a lot of people choose to just drill little pilot holes there and it comes with the screws
that you can use with a spring and they're spring loaded so the pickup becomes adjustable
on the on the plastic pick guard similar to the other strat pickups so you have your choice
or you can use double-sided sticky tape comes with a bunch of sticky tapes of different sizes
so you can actually sticky tape all this stuff to your guitar but that wouldn't be too good for
your finish come to take it off later depending on what kind of finish you have it may not like
that glue too well so this method does not involve any any taping whatsoever on this guitar
everything that I've chosen to do will not require much of the stuff that that shipped with it
so the next thing we do now we have this setup is we need to find out how much cord we need
and there's a little spot on the back of this unit there's a little hole where you can coil up
the cord now I already I already figured out that I need to go around twice
inside and before I do that though because I'll just lose it if I don't there's three screws
that have arrow markings it probably won't show up on the video but when you get the unit you'll
see there's three arrows pointing to three screws so what you gotta do now is take those screws out
because we need those screws to attach the plate this is the mounting bracket that attaches to your
guitar but it goes on the back of the unit so we need to remove the screws first now once we get
the screws out then you can coil the wire and this way I don't have to deal with the coiled wire
inside of it while I'm working on it I can just not worry about the wire right now
remove these three screws I was a bit skeptical about doing this so I was happy to see because
this model guitar is also an arch top but unlike a Les Paul the Schecter models have a flat top
on them up here and if you mount it to the bridge piece using the bridge mounting bracket
you don't have to worry about it being curved or not anyway
so I was a little worried about how this is going to go on the guitar because
right in here there's a nice little slope and this is not curved for I uh it's just straight
so it'll slap itself right on a Stratocaster or flat top very nicely but I didn't know what to do
so I had to do research and then I found out about the rubber pads that come with it which
you'll see me and that you put underneath it so that helps so we can put the coil wire in there
and I already know it's two times so now this becomes a cover for this to hold your wire in
place and then you just put the screws back in and that's all that's required for this unit
as far as any kind of an assembly goes now this uh bracket is steel it's very sturdy steel
but there are rubber padding glued to it to protect your guitar's finish and that's it now
it's all set up and the the uh the wire looks good it's not quite going to go around another time so
I already figured that out um now the next thing you do once you get this step done
is you need to loosen your strap bolt on the end of your guitar there I've already loosened this
one I use the Marzio's uh quick clip straps quick locks now this end piece here has a big slot in it
and there's a protruding screw it's not actually it's well yeah it's a screw I guess
that's for the other bracket here so we're going to sandwich the guitar body right in here okay
so remember all this stuff does have cushion on it so you're not going to damage your guitar at all
so we just slide this over on a guitar now if we just did that this is going to be at an angle
you're not going to be able to tighten this up and it's going to look terrible so what you got
to do if you have an arch top is you got to take one or two of these I'm taking two because that's
what I need now two of these will insert right in here right underneath it and it's actually
the opposite angle now it's just a little too high but just a little bit not very much
so what I need to do is just push it down just a little bit and then tighten this
well tighten the screw up perfect okay now this will work just fine if you have locking
you know shawler system on your guitar for your guitar straps you're just not going to have any
issues here it's just simply loosening the screws slipping this thing in there and that's it
so as you can see now it's looking almost complete the next step you got to do is take
this bracket slip it underneath the back and over the screw on this side here
you can see how that goes just like that and it comes with a washer a lock nut
and a nice handy dandy actually decent looking end cap screw there
or I guess you could say an end cap nut
so the next thing you want to do is make sure you get this slightly snug together
and then lock it down and that's the assembly here now the the cable will be
semi neatly out of the way because it's not got all that extra line sticking out here and getting
in your way and the other thing you need to do is take this line I've wondered for a while it's
why is this little hook there that's so you can tuck the line underneath and it'll help to
keep that under the out of the way now I'm going to probably put it in there something like that
because that way the strings will go over the top and this part of my guitar will be nice and clean
and that's it now all I have to do is restring it and make sure that the pickup height is all
set perfect with this little gauge and if it's not then I would just remove this because it's
not bolted down it's right now it's just easy to remove and I could either take out or add
little plastic spacers that come with it these are just little black pieces of hard plastic
of different thicknesses until I get the right height okay and if it's too high it does come
with some metal washers that are meant to go underneath your bridge and just sit right on
top of here so it'll actually lift your bridge up if you can't get it to quite mesh the properly
properly so there's lots of options to get it right but the way it looks to me is this went
a lot better and a lot quicker than I thought it was going to go so that's just about it there's
no need to keep this going that's it so I hope you found it a little bit more informative when
I went to buy this I was looking all over YouTube and all I seen was quick animations of it slapping
on the guitar but nobody really doing it so now at least I've got a video out there that actually
you can actually see it done at least in this format so I hope you found it helpful if so
subscribe I'll be doing more I have the Roland GR55 which came with this GK3 that's why I'm
doing the install and so I'm looking forward to doing some videos on how to set that up
as I learn how to do it and hopefully help people out this is my first time messing
with a MIDI guitar I've been dying to do it and I'm so happy that I'm able to do that now
and I plan on doing this install on my Schecter C1 EA but I will be doing a video
on that guitar as well but it is going to be a ghost MIDI system install since that guitar already
has a ghost piezo pickup system in it I see no reason to add this pickup system to it when it's
already fully MIDI capable if I just add the daughterboard to it so I'll be doing a future
video on that in a couple months that'll be several hundred dollars investing in that but
it's gonna be worth it so that'll be another video on the C1 EA which is like half of my
videos I think are customizing that guitar so I hope you all find it helpful let me know what you
think post any questions you have about the install I've thoroughly read up on how the
install is done so if you have a question feel free to leave one so thank you for watching and
happy MIDIing well thanks for watching and see you next time on guitar tech how to do it yourself
