Graphtech MidDark Switch Install

TheGospelGuitarist
1 follower
Mar 30, 2026
Installation of the Graphtech Ghost Mid/Dark Acoustic switch into a Schecter C1 E/A.
AI Generated·May contain errors
Hi, I'm Mike Sullivan. Welcome to Guitar Tech. How to do it yourself.
Well, I bet you're wondering why this guitar is sitting here and why I have blue tape right here.
Well, it's because, yes, it's another customizing video for my C1E-A.
And because it's got the Ghost piezo system installed in it,
they give you the option of buying this little switch, and it's called a mid-dark switch.
And so I'm going to install it right here.
So it'll be on there, and it will give me two different tones for the acoustic sound.
So basically it's a mid-boost that's in the circuitry on the motherboard inside.
So today I will be doing an install of this switch on the guitar.
This switch, if you're not familiar with this guitar, this switch just has a magnetics only in the middle.
It's the magnets and the piezo or the acoustic piezo all by itself.
And then this switch will give me two tones of acoustic.
So obviously I'm going to have to de-string it, pull all these things apart.
It's got a wiring harness, and so I have to go through and get all the wiring for the two volume controls.
The magnetics will be on the green and black wire,
and then the red, yellow, blue are going through the switch and into the acoustic volume control.
So that both of these volume controls will be done with the one harness.
So it'll be replacing the two harnesses that are already installed in the guitar.
Seems like a lot to do, doesn't it?
But that's the way they want it done, so that's the way I'm going to do it.
And as you can see, I've also moved the Roland GK3 has now been moved to this guitar as well.
So to make a long video short, I'm not going to be running the video for the entire time.
I'll be jumping around to make it go by quicker.
So the first thing I've got to do is drill a hole right here,
and then I've got to rip all this thing apart.
So we'll see how it goes.
Well, okay, that went very well.
I took the blue tape off, and it's nice to see that none of the finish cracked or split off of the wood there.
It's got a really nice, solid edge on it.
I was a little worried because I hear sometimes that the finishes can be a little bit brittle.
But it worked just fine, and it's just big enough to where that fits nice and snug in there.
It's a quarter-inch hole, in case anybody's wondering.
And that fit just perfect.
So on to disassembly now, so I can take everything else apart.
That was the heart attack episode there.
I hate drilling holes in nice guitars.
Well, looks like the strings and knobs are gone.
Okay, there's a shot of the preamp that's underneath the bridge pickup cavity,
which is where the work will be done on this end in this area.
Time to take off the nuts on the controls here.
And instead of using the open end and risking scratching your instrument,
I would always use the enclosed end because it fits right on there,
and it's not going to wiggle off and scratch your finish.
Another way to go is with a socket, but you need real deep sockets
because these usually get in the way of smaller sockets.
You just bottom out before it seats.
So I usually just grab an open end to take care of this job here.
Okay, I pulled the magnetic volume through the access port here.
And the other thing I will do is I will reattach the nut
so that these other parts will not fall off into the guitar while I'm working on it.
On this particular pot, I have the green and the black wire here will be removed
and replaced with the green and black off of the new installed switch.
And that's the work to be done on this part of the guitar.
Okay, continuing here, I have now removed the acoustic volume pot.
And once again, put the nut on there so I don't lose all those parts.
The way the wiring is laid out, the green and black wire will be attaching
to the electric magnetic pot here.
Nothing will go there.
Just these two wires, the black and green, will connect that to the circuit.
And this will be replacing the wire that's already down there on the board.
And then these other wires here, the red wire will be attaching to the acoustic volume
as will the black and the yellow.
As you can see, there's a violet, a yellow, and a black.
Well, on the switch, the violet goes to the switch.
And then the red will return it back to the volume pot.
See, we're just putting the switch right in the middle of the circuit there.
So it's all pre-wired for you. You don't have to worry about it.
You just got to keep all these color codes straight.
There's two different sections in the manual.
One that covers this and another section where it covers this.
So you can't just go with one part of the manual.
You got to search your way through the whole manual to figure this out.
Because this guitar purchased new is wired a little bit differently than what you would do with a ghost.
They didn't install all of the switches. It's kind of a custom piece.
So I'm just customizing a custom piece, right?
So now that I know where my wires are going, and you don't have to undo too much,
I'll just add a red wire there going to the switch.
Unsolder these.
Unsolder the green and black from this switch.
And then pull the bodies of those off of the motherboard in here.
I'll probably move the camera to show what I'm doing in a few minutes.
Right now I'm going to put this into the guitar and get it installed so I can pull the wires through.
Okay, having lots of fun so far.
As you can see, I've got the switch installed.
The washers were slightly different, so I had to hunt down two matching washers so it would look good.
And I have also routed through some of the wiring.
So the red wire coming off of the switch, which will attach to my acoustic volume pot here,
I will detach all three of these wires.
And I have twisted a pair here of the black and yellow wire,
which will go where these black and yellow wires are.
The red one will go where the violet one is.
And that will wire up the acoustic volume to the switch.
And over here I have twisted the black and green pair together,
because it's already a snake's nest in there, okay?
If I can twist some of the wires together while I'm doing an install,
it just will keep things a little less tangled up inside.
I don't have a whole lot of leeway here with this other set of wires.
Also, a real quick tip is, I don't...
See, these wires are bare.
I stripped them already because I don't need to go through the body with them.
But with these two, you do need to route it underneath the top.
So having them just blunt-ended the way they come,
you're just going to mess up the bare wire anyway
if you try to get it through there. It gets caught on things.
So this way it just routes through a lot easier.
And then when you're ready to attach it, then strip it.
These two here are ready because the pot's right here,
where it's accessible, and then I'll just install it right there.
So these two wires will be connected,
and that part will be done for the magnetic.
And once I get the wires pulled off,
I can then pull them off the motherboard
with these connections here connecting everything.
So they will be replaced with this bus connector right here.
Something else I wanted to point out real quick.
I noticed on the instructions that it says to put the bridge,
the Tone Pro's bridge, with the screws facing the neck,
or facing your bridge pickup.
And virtually every guitar that I've owned like this or seen online
has the screws facing the tailpiece.
Well, Graphtec says that's going to cut down on your volume output,
so if you want to have fuller tone,
to have the screws facing the neck.
So I'm going to see if that's the case.
I don't think that Schecter had Graphtec reverse the seats.
I just would think that they just come off production,
and they're not specifically customized for Schecter
just to put the screws in the back.
So I'm thinking that this is a production model,
so I'm going to flip it around the way they say to install it.
And as you can see, there's still enough clearance
for the GK3 Roland pickup to be mounted underneath it.
It will clear the screws.
It does pull out far enough towards the bridge
so that the screws can fit between the two.
So we'll see how that sounds once I get it all wired up again.
Okay, I wanted to show now that this is the installed harness
that comes in the guitar with the Ghost system.
It has five wires on it.
The green and black one,
which originally, coming off the motherboard,
are attached to the magnetic volume control,
which is right here.
The other three are routed through the body
to this control for your acoustic piezo volume,
and it contains the purple, yellow, and black wire.
And so once you desolder them from the pots,
you can pull this out of the guitar and get it out of the way.
As I've mentioned, it's a snake pit in there.
You don't need these things in the way.
Now I'm going to save these because you never know.
It might come in handy at some point in the future.
So now it is ready for soldering of the pots,
and then I can reconnect this to the motherboard.
Okay, some of the wiring finished now.
As you can see, the green wire and the black wire
on the outside lug, green wire on the inside lug,
and the original pickups are connected where they were.
I didn't touch those.
So this is ready to be reinstalled after I check it.
Also, on this side of the guitar with the acoustic side,
the black, yellow, and red wires are now attached to the potentiometer.
It's kind of easy going once you get past the routing of everything.
Soldering is a piece of cake.
So now it's cooling off and getting ready to be tested.
Another little keynote was,
in case you're wondering how I got this switch in here,
it's kind of a stretch to get from the F hole way back here.
It's funny because I didn't really consider that until I drilled the hole,
but I figured, hey, the other switch is there, right?
They had to get it in there somehow.
Well, it took me five seconds or so to figure it out,
and then I thought, hey, there's a big access port right there.
So that's a way in where you can get your fingers inside the guitar
to help work any additional switches into the instrument.
So in case you're wondering how that went,
I didn't use any wires to pull wires through.
It's just all finger work.
And later, I will probably install maybe two more switches
because maybe in another year or so,
I will be doing the MIDI upgrade to the guitar.
Right now, I'm just saving a couple hundred bucks by using the Roland unit on it.
Now for the testing.
Okay, I've been through everything.
Everything is working.
And go through all the different switch settings.
You can do the normal tap testing on all your mics
and making sure all the outputs are working
and the bind controls are doing what they're supposed to do
and all of the switches.
So all the wiring works and is solid.
So at this point, I can shut the power amp down
and put it back together.
And then we'll test it again.
Well, okay, got her back together again and tested a second time.
So nothing came loose with installing everything back as it should be.
You always want to do that twice
because check the wiring before you put it together.
That way, it's already apart in case something's wrong.
But in putting electronics back together,
sometimes you can just make a bad connection
just by hand pressure on a wire somewhere
while you're putting it back together.
So once you get it back together, run through the same check
on all of the systems and make sure they all work.
So this will now get new strings on it
and I will play test it and should be good to go.
So I hope you found the video a little helpful.
Since the mid-tone switch, all it is is basically a mid-boost
to the acoustic piezo system
that's wired into the acoustics volume control.
So it comes, it's like $35 I believe it was
for the whole harness and so I thought I'd show the install on it
to add yet one more feature to my C1EA.
And if you're interested, it's not too bad of an install.
So just make sure that you research the instructions
and know where the wires go.
And I had absolutely no problem.
Didn't have to rewire anything.
It went right the first time.
So I'm happy with that.
So I hope you found the video helpful, insightful
and please subscribe and like and share with your friends.
Especially if they own this guitar.
So thanks for watching and have a good day now.
Well thanks for watching and see you next time on Guitar Tech.
How to do it yourself.
