GK-3 Fixed

TheGospelGuitarist
1 follower
1 Video View·Mar 30, 2026
Follow along with me as I problem solve my GK-3 midi pickup. This may be a common problem which hides itself as a bad connection.
Hi, Gospel Guitarist here today. I'm going to try to repair
my GK3 wiring going in to the pickup and get this pickup right here under the second string.
See if I can't get it working again and I'll videotape the process and hopefully show you
what you got to do in case it happens to you too and it's happening to a lot of people. So
hopefully this will be a helpful video for anyone that owns this unit.
Okay, we got this unit off the guitar here and the mounting bracket is still on the guitar but
next we got to bend these little tongue whatever you call them tabs that are holding on the metal
casing right here to remove it from this plastic motherboard which these things are all attached to
so all you have to do is use your flathead screwdriver to just bend these up and then
the whole thing starts to pull loose. Okay, one of the things you're going to have to do
to get this apart is you're going to have to take this height adjustment screw in the middle
and unscrew it completely so that it releases from the pickup motherboard
and then you're left with this and you have access to these fine wires right in here.
Okay, as you can see we're talking pretty seriously small soldering joints here
and if you flip them around there are little silver dots on the back.
I'm trying not to bend this away from here like this because this plastic will break right here
if I keep bending it so you can see the little solder points here. Now on mine all of these
points are actually soldered but when I put pressure, I believe it was on this one, I'm
going to check here in a minute again to make sure I heat the right one. It might just be a
solder joint so I'm going to reheat these and make sure I get a good connection in there.
The wires are not loose, they are connected but it is intermittent and so as you can see
here's a good shot of the little soldering joints right here. Trying to get light on it,
it's very difficult to get the angle for you. Okay, to my surprise all the wires
were still soldered on the bottom and I had the idea looking at how tightly crimped this was on
this wire on the cable jacket there, see how tight that is. I wondered if that's crimping
one of the connections and so I grabbed this and I kind of twisted this around a little bit and now
I have my second pickup working again and I haven't done any soldering at all. I believe
it just was too tight on here. I may remove this thing completely and use electrical tape or shrink
wrap or something around this thing. I'm not sure yet, I'll get back to you in a minute on what I do
here but apparently it just got pinched inside there because like I say all of the little
solder joints on the bottom down here are all intact. All the wires are still intact and when
I move the wire a little bit I can get a connection with the second pickup and even right now just by
me holding this and moving I'm seeing a registration on all of the six pickups so
all the connections are working. But when they install this metal cover to protect the wires
they have to crimp it and have it grab onto the outer casing but it looks like they may be
crimping it a little too tight and it's pinching the wires. Now is it broken inside? I don't know
if it's broken inside. I'd have to obviously go up here and cut off this and then completely rewire
everything but I'm going to go with this being pinched right now since it still works
and try to remove this thing and go from there. Okay what I did was I wound up
loosening the metal plate's grip on the cable as it comes in so it just basically
goes through the cable feeds through the two tongs like this but they don't crimp on it.
I super glued the screw plate back on and then I took a little piece of tape here and
wrapped the tape around it just some electrical tape just to help reinforce this area a little
bit. There's not a lot you can do because there's the motherboards under here so you can't really
use a better screw without risking damaging something on the motherboard below it so
but I still have all six poles are still working so I'm going to reinstall it on a guitar now
and make sure it still works. Okay as you can see looking at the display on the
synthesizer that's the second string registering again first second. The second one was not
working now it is and it was all because of a pinched cable. They all work I'm back in business
and I didn't even touch a soldering iron so before you go messing with this stuff it just
really pays to check everything about your wire. All it was was a pinched cable coming into the
pickup there was nothing wrong with it at all it was just simply pinched and must have been
shorting it out somehow. So I have the repair done and the GK3 is back up and running.
Thanks for watching I hope this helps somebody debug what's going on in theirs. I have read where
people have had broken wires on those little tiny connections showed earlier in the video
and people have had issues with the midi cable coming you know from the GK3 to the
GR55 so really check over your cables before you break out the soldering iron and have it ready
like I've had it sitting here hot on standby and hoping I didn't have to use it and I didn't and
so I got lucky this time. So thanks for watching and please remember to subscribe and if you know
anybody that has this problem please forward them this video so thanks and take care.
