Carvin Quad X Front Panel Features

TheGospelGuitarist
1 follower
Mar 30, 2026
Detailed information about the front panel of the Carvin Quad X guitar preamp.
Hey Gospel Guitars here with another video on the Quad X
guitar preamp as you can see sitting here. Let's take a closer look and go over all the
features of the front panel. Okay starting at the left side on the upper row we have a channel
select switch which is a momentary switch so that you can click in and out on the channels
without the foot switch you have your input for your guitar you've got a boost switch you have a
bright switch and you have an input level indicator with a zero and a peak indicator
they go from yellow through green into red and the boost and brights are available on all the
channels sliding over now we have the channel 2 and channel 3 cloaking device
which comes in handy if you're on stage and your lows are interfering with say a keyboardist or
another guitarist you can start to turn this up and what it actually does by turning it up is it
takes out the low mids out of this signal the lows and the low mids and cleans up your guitar signal
so you're not stomping on say the low keyboard notes that's the cloaking device next to that
you've got your noise gate which is very good and very useful and effective with this knob you also
have a pass indicator which is a green led and a hold indicator with a red led and next to that we
have our reverb section which has also got a on and off switch with a red light indicator and this
will operate the onboard spring reverb unit which is an Accutronics spring reverb and they're very
good quality another feature that the front panel gives you is the cabinet voicing switch for
recording or just running the unit straight to a mixer so that it will emulate being connected to
a 412 cabinet so if you're in the recording studio it is connected to xlr outputs so that you can run
it straight into the mixing board and sound like you're playing through a full stack we have our
master effects loop switch with a red indicator also the other thing about the reverb and the
master effects loops are also memory switchable for the channels in other words when you change
channels your channels remember which effects are turned on and which ones are turned off
next to that you have your two outputs you've got your stereo output and then you've got a mono
output which is also an xlr jack on the back i will be doing a video on all the features on the
the last thing on here is the graphic eq switch switchable with all the channels
and it's a five band graphic eq now let's go take a look at the channels on the bottom row
channel one is your clean channel and it has a three bands eq low mids and highs all eqs
on this unit are active which means five is like zero you're not adding or taking away
from say your mids so if i go to three on my mids i'm actually subtracting the mid signal from the
from the unit if i go over five then the unit is boosting those frequencies these are not like
passive marshall fender guitar amps where their controls are totally passive and unless it's on
10 you're actually just subtracting the signal from the frequencies those are subtractive controls
these are active controls so five is the center point and you are actually adding
boosting these signals so these are extremely flexible eqs so that's channel one pretty
straightforward channel two now channel two and three are grouped in one group we have a volume
control for channel two which is labeled clean and then you have the channel three crunch volume so
the two volumes for channel two and three are grouped right together next over we've got our
overdrive control and then we got our low and our high control now the low and high control here is
shared with channels two and three the overdrive is only applicable to the crunch channel on channel
three up here as i mentioned we have the cloaking device for channel two and three so this this
device works with either one of these channels going over to channel four this is the sustained
channel we have our volume control our overdrive lows mids and highs so that's the layout on the
x100b's front panel spelling out all the controls for you let me get a closer look at the eq for you
in case you're wondering what frequencies are on board okay here's the frequencies we have 75 hertz
150 hertz 1k 3k and 6k and the faders are nice and smooth and one of the things that i would
recommend doing is when you go to clean these they can just fall right off and people lose them
take it off put a little spot of super glue in there and then stick them back on and you won't
have that problem so that's it power indicators right here so that is the quad x amp front panel
description of all the controls and buttons and look forward to the next video on all of the rear
features
