Raxess Guitar Rack Build

TheGospelGuitarist
1 follower
Mar 30, 2026
Follow my guitar rack build which is not as slow as it first appears to be. I assemble a new Raxess 6 space rack and load it with my rack guitar system.
AI Generated·May contain errors
Hey, Gospel Guitars here, and I have an unboxing coming at you.
And, right here, I know, you can't see it.
But anyway, it's just a big box.
And in it is the Raxus Six Space Studio Rack.
And I know they're really simple to put together and all that,
but you never know who would want to see one go together.
And I will discuss the quality of the build and the materials
as I put together my new guitar rack system.
So, follow along, okay?
Okay, after I got the box open, just to show you how it comes shipped,
you've got your bag of goodies here with your instructions.
Wrapping paper.
And it's all kind of seems to be well-protected inside.
There's not a lot to these, of course.
Your rack rails.
And then your top and bottom and the two sides.
Taking a look at it, it's pre-drilled holes, of course.
Both sides are laminated and it is finished on all the edges.
Just checking them off for any damage or anything.
Not that it would make me send it back.
But, and there you go.
Okay, the sides are going to be covered here with the top and bottom,
so you don't need to finish that.
And they should be sinking.
Let's see.
And then the other side.
Everything seems to be in order.
And that's it for the unboxing.
Okay, first thing you do is you take one of the sides,
and there are pilot holes for where your rack rails go.
There's four of them.
You'll use the big holes for your screws.
In this model, they give you a lot of screws, which you only use two.
I think I got ten screws.
Very simple build here.
And you'll want to screw these down.
And on the rails, on the front of the rail is numbers one through six.
And one has an L at the bottom, and the other one has an R for right.
So, this is going to be the left side of my rack.
Now, obviously, I'm not going to put the right rack rail in these other pilot holes,
because that's the back.
So, they did drill extra pilot holes, but maybe later, if you need to,
you can buy some more of these rack rails and mount them on the back
if you have some real short gears, like little short power units or something.
You want to get them really tight, but you don't want to keep turning once they get there,
because this is just a particle board, and it'll just start chewing it up.
So, just two screws here.
If I really wanted to, I could put two in here just for good measure.
And I think I will, because I got the extra screws,
and because I'm putting a very heavy Marshall power amp in this thing.
So, a little bit of, maybe it'll just make it a little stronger.
Who knows? Why waste the screws, right?
So, I don't have any pilot holes, but it should be just fine.
Went in just fine.
These are nice, sharp-pointed screws.
So, if you want to do this, don't hesitate.
You don't have to break a drill out first.
They go in quite easily.
Just a little effort to get it started.
Now, just repeat for the other side.
Okay, so when you're done with your two sides,
you should wind up with something like this.
One-sixth right, one-sixth left.
Four screws in each side.
Now I'm ready to attach the top and bottom.
Okay, once you get that done,
you're going to want to take one of the tops or bottoms,
get your long wood screws,
and you're going to line up the screw.
It'll go through the hole nice and loose.
And line it up with the starter hole in your bottom or your top,
whatever you want to call it.
And I'm giving it a good start,
but don't tack it down too tight
because these things are loose and moving around,
so you want to get it started first,
so that'll help get it stable.
Okay, now with this side attached,
time to attach...
Let's see, what did I attach to the top?
So I guess I'm attaching the bottom next.
Okay, here it is with the two sides attached.
So you didn't go to the bottom, you went to the side next.
So now the next thing to do is install the bottom on it,
and then it will be done.
Also, you notice you can't see the screws
because it's got little plastic caps that go over the screws
and make it look nice.
You just push those in, and you're done.
One word of warning, I broke out the drill
because the pilot holes are extremely tight
once you get past the halfway point,
and doing it by hand, well, not a good idea.
So I broke the drill out before I broke my hand.
So it's either that or drill the holes over.
So they're very, very tight and snug,
so I don't want to loosen them up.
So use your drill to screw them in.
Well, once you flip it over,
I just have it sitting on a stool here.
Because the rack rails are installed,
it sits right on the rack rail on the front,
which allows you to put a starter screw in the back
to hold up this side.
Then you just stick in the rest of your screws,
then I'll tack it with the drill.
Okay, gang, here it is, all complete.
It didn't take too long to do.
I had a couple issues.
When you do use a drill,
be sure you can get the kit that I have
with the normal tool kits you get.
It was marked number three, and it was extremely huge.
And it had the plus sign with the number three for the bit.
It didn't have the plus sign with the little circle or anything.
It was an exact cross, so just like a plus sign
because different kinds of bits, you know.
And it worked real well driving them in
where the other bits of similar size
just would want to strip them out.
So very large bit recommended.
But it's a nice case.
Everything went well.
So now to stuff it full of stuff.
So now to put in my guitar rack stuff.
When you do this, you want to set it down on the floor
is the easiest way.
And I'll show you here.
Watch this.
Okay, so the easiest way to load your racks
is not in a vertical position,
but sitting on the ground,
especially when you're dealing with really heavy gear.
And the first thing that you want to know when you load racks
is start at the bottom.
In this position, what's nice is you don't have to start at the bottom.
You can start at the top.
And then you can play with where you want stuff
if you change your mind.
Then when you finally figure out where you want everything,
you can bolt it down.
But if it's vertical in a normal position,
you want to build where you rack from the bottom to the top.
It's just easier, you know.
Now the first thing to go in here is this monster
Marshall power amp of mine.
Does that look classy or what?
Yeah.
So the second thing that I'm...
This is where I'm not sure which order I want to go in,
but I think I know the order I want to go in.
What do you guys think?
I'm thinking carbon quad X next.
Now I can go two ways.
I can have this at the top,
or I can have it down here.
Of course, it looks so cool like that, you know.
But if I put it up here, it looks kind of cool too.
And what I'm going to do for now is use my Yamaha.
I think I'll find a Yamaha SPX 90 on eBay or something.
They're pretty high quality stuff.
Even with this unit, I was getting really cool sounds.
So I could go with that look.
Then I can just put my screws in.
Screw these puppies in.
I need to go get some more screws here.
And I'll let you see it once I get it all screwed in
and put on top of my 412 cab.
I am going to make one more addition to the rack, though.
I have a couple of little plastic feet with a furry bottom on them.
And that way, this direct wood on top of my 412,
as I'm moving it around, will not tear up the vinyl or the cabinet.
And because these are furry, it will allow me to spin it around
easier than if they were rubber.
They'll slide around a little bit.
So I just need to measure out where to put these
so that they'll sit on the 412 properly.
Okay, in case you want to do this too,
I use my little fuzzies that I just told you about.
Actually, I have a bottom 412 cab, so it's a larger, wider top.
It's 14 inches across the top.
And the case is 16 inches,
so basically you need to be at least an inch in.
And if you line them up, actually, on these screws
that you just installed to build the case,
this one actually is measured an inch, so it's a little short,
but you can just use these end screws as a piece.
Go in two inches and you'll be fine.
So that's it for the build.
Now to get it up on the cabinet.
Oh, back don't fail me now.
Well, here she is, up on top of my 412 cab,
which is also carbon.
Carbon GX412.
British, carbon British speakers.
I believe they're made by Celestion.
So that's the rack complete.
Now I just need to wire it.
And I'm waiting on some tubes, which will be the next video
on completing the retubing on the carbon quad X.
And I will show and talk about the tubes installed,
and I will do audio demos of the full half stack here.
So stay tuned for that.
And thanks for watching.
Here's a higher angle view right there.
So that's what it looks like.
Basically, it's just going to be studio gear.
So it's not really going to go out maybe once.
And I'll need a tow truck to do it.
So thanks for watching.
Please subscribe and like and share this video
and all the other videos I'm turning out.
And thanks for helping me to break the 1000 mark this year
for subscribers.
And I'm approaching the half million mark in views.
So thanks to all of you for that.
