STUNNING Restoration of Neglected Mid-century dresser!

Antique Art Deco
12 followers
I rescue a neglected mid-century walnut dresser and restore it to its former glory! Watch as I strip away layers of paint, repair veneer, sand, and refinish the wood to reveal a beautiful MCM piece. If you love mid-century modern furniture, vintage makeovers, or satisfying DIY restorations, this transformation is a must-see.
#furnitureflip #furnituremakeover #midcenturyfurniture
You might also enjoy: • MCM Redo - Mid Century Furniture Restorations
AI Generated·May contain errors
Found a beautiful mid-century bedroom set at an auction recently.
It was made by the manufacturer called Widdicombe Furniture.
I was not really familiar with them but did a bit of research and found out that
they were from Grand Rapids, Michigan and they made
lovely furniture during the mid-century. This particular one that I have, the
six-drawer dresser right here, is a walnut dresser, really really
solidly made. It was in surprisingly good condition
except obviously for the failing finish on the top. But structurally it
there was nothing loose, it was solid, no major repairs were needed. It was
mostly just finish issues.
The dovetail joinery was rock solid, didn't have to do any repairs.
On the bottom of the dresser in the middle there was an extra support sort
of leg that they had built which was really nice because it just gives more
extra stability to the piece. The veneer went all the way down to the
bottom. There was very very few chips out of it
so that was great. And you've got to love a piece of
furniture where the manufacturer actually finishes
off the back just as nice as the front. Nice solid piece of walnut veneer on the
back of the piece. I started by scraping the finish off
but it didn't take me very long to figure out I don't want to do this
because it was really hard to scrape it off.
I was using using a lot of pressure and it's a big piece.
So I opted for chemical stripper and I had to do several coats of this
but it did come off.
Stripping can be quite messy so I decided to add some
newspaper on the pieces of wood underneath the
top of the dresser just so that drips wouldn't get all over it.
Because I was creating a little bit of a mess here so that helped.
Now on to stripping the dresser drawers. I'm in Canada so I use circa 1850
to get off the finish. I know you can't get that everywhere but that's what I
use. It works pretty good you know I have no
complaints. Sometimes I with something like this the
the parts that weren't failing were on really well so
I had to do a couple coats of the stripper in order to get it all off
but with a little bit of patience it did come all off.
After the initial stripping of the furniture I often go back with
steel wool and just go over the whole thing. It just helps
get little pieces out of the nooks and crannies.
Mineral spirits is the last step before sanding.
The stripper has done its job and then I just go over the whole piece with
mineral spirits. Helps clean all the extra little pieces off and
makes it really clean. After the stripping was done
I used a 120 grit sandpaper to get the remaining bits and pieces
off the front of the drawers.
As you can see I follow the grain that way you're not going to get marks
or as many marks on the piece and I always wear gloves because for
some reason I just can't stand the feel of sawdust on my fingers.
I use a little dental pick to get the little pieces of paint and
grain filler and stuff out of the hard to access
areas and I go back to sanding. I just keep switching back and forth and
keep moving along and you know I might finish the whole drawer front and then
go over it one more time. Every time I look back on it I'll get a
few more pieces out. It depends on how picky you are.
I'm pretty picky so I'll do this several times.
I finished sanding the solid walnut poles with 120 and got most of the
finish off. They're looking good now so I'm moving on to 150 grit which I
am going to do the drawer fronts with. I don't like to use 120 because it can
be a little bit aggressive on veneer and I'm hand sanding anyways right now
so it's pretty gentle on the veneer and this veneer is thick so I'm not worried
about sanding through anything. I do have to fix that little missing
piece of veneer on the corner which I'll do
a little later in the video. Okay now I'm going to address this little
patch that I have to do. First of all there's
a bit of the finish or something left right on top of where the gouge is
and so I took my scraper and tried to get it off.
I was having a difficult time. Some of it was coming off but it wasn't all coming
off so I had to do a few other things to try to
get it all off. Okay the second attempt was to use 80
grit sandpaper on that area to try to get
some of that finish or whatever that was. It was
like a grain filler or something. I could tell that the veneer was
underneath it. I sprayed a bit of water on it just to
see the difference so I can see how much of
it was left and to my surprise there's still quite a bit of it left because
it's very close in color to the the actual wood veneer. So I had to try
something else because obviously the sandpaper wasn't working that great
so I opted to get some paint stripper and try to use that to take it off.
After the first application of the paint stripper it still wasn't
all off so I gave it a second dab. The paint stripper waited a little bit
and went at it again with the steel wool. This time I added a dental pick and
that seemed to do the trick.
So here is the piece all finished and all
cleaned up and ready to fill. Unfortunately I didn't videotape the
filling part but what I did is took epoxy putty,
filled the little hole and then leveled it out with some sanding
and then stained and impainted it and you barely noticed it after that.
This is the top of the dresser after I had sanded it,
stripped it and sanded it. It looked pretty good
except for the big black stain that was on
one end of it. I knew from previous experience and application that I had to
put some oxalic acid onto it to bleach it
out. It took two applications and the stain
disappeared really. There was very very little left of it
and I was quite happy with the results. I sprayed it down with some water and
this is what it looked like after I had used the oxalic acid. Barely
visible. I knew that once I'd put the general
finishes stain on it you wouldn't even notice the
whatever was left over from the black area.
It would have been right there so not bad.
Another repair to the exterior of the dresser
is this piece of veneer that's missing in the corner.
So what I opted to do for this repair is I had quite a bit of walnut veneer
so I cut out pieces the size of the little cutout and I just stacked
glued them and stacked them and glued them in there and it seemed to
do the trick. I used my chisel just to even out the
wood a little bit before adding the pieces in.
I think I had four pieces in total and what I did
is I added each layer with some wood glue
and then would put the next layer on top of that add more wood glue and keep
doing that until they were all in place. After the repair was done
and I let it dry and the whole side was sanded
I stained the piece with nutmeg general finishes nutmeg and
it covered it quite well. With a little bit of painting
in painting at the end it fixed it up so you could barely see it.
The reality of refinishing furniture is you have to have patience. Stripping
whether you strip chemically whether you sand the finish
off or whether you scrape it off it takes a while and sometimes you have
to do it repeatedly. You can't go in into it thinking that
oh yeah I'll finish it in a day or two usually unless you've got like you know
12 hours in a day to work on it but most people don't so usually it's going
to take you a while to do it. You work for a few hours here and
there and get the job done. Now that the dresser is sanded
I'm going to tape off the inside of where the drawers go
so I don't get stain all over the inside. It just makes it look messy
if you don't and then you see little bits of stain all you know
inside the doors so that's what I'm doing right now.
I'm finally ready for the stain and I chose nutmeg
for its nice warm brown. The reason I added a stain to this because
normally you don't really have to stain walnut because it
has its own really nice natural color but I had to do quite a bit of
lightening on the top of the dresser with oxalic acid because of the
black stain that was on the top so I decided that
in order to even the color out everywhere I should probably stain it
and that's why I chose this. One of my favorite stains is
General Finishes Nutmeg. I love the color on walnut it gives it that nice
rich brown but I also like the way it just goes on the furniture
it doesn't dry really fast so you don't get that streaking that sometimes
happens it's just it goes on really smooth
it's just a pleasure to use.
I chose Odie's Oil for the top coat on this piece of furniture
for a couple of reasons. The first reason is I just genuinely really like the
finish that it gives the furniture it looks really good it's not
really high luster but there's a nice sheen on it
but the second reason is I and during the colder months I refinished furniture
in my basement and I just can't do anything that's really
stinky or smelly and Odie's Oil smells really good and it's not
overwhelming or anything so I tend to use
hard wax oils and finishes that don't have
high odors in the winter months.
Okay the Odie's Oil has sat for about an hour or so
and I am going to come and buff it off now.
Often I use just cotton old like cotton bath towels and stuff to
take the finish off but today I ran out of
old cotton towels so I was using my shop rag which seemed to do the job okay.
After I buffed off most of the Odie's Oil I used my scraper to get into the
line along the edge of the hull or the drawer handle
along the front to get all the stuff out of that area.
I oiled the underside of the dresser as well it was really dried out the wood and
it looked like it just needed some nourishing so I added oil there.
These little brackets were on the underside of the dresser
I think they just add a little bit of stability to the sides
but they're also very decorative. When I first got the piece they were nasty
looking as you can see by this picture here
but once I used a little bit of elbow grease barkeeper's friends they shone up
really nice and it's just a nice little extra feature.
The last step was to oil the entire outside
of the dresser. I did the sides, the tops, the front
I even did the back, the under undersides,
the drawers had been done and after it was oiled and completely buffed
and then buffed again just to make sure there was no going to be no streaks on
it then it was ready for the reveal.
